What are the characteristics of Sick Sensors – Contrast Sensors?

1. First of all, the front face of the photoelectric sensor must be parallel to the surface of the workpiece or object to be detected, so that the conversion efficiency of the photoelectric sensor will become high. 2. When installing and welding, the small distance between the root of the pin of the photoelectric sensor and the pad shall not be less than 5 mm, otherwise ...

1. The signal cable of the sensor should not be arranged in parallel with the strong current power line or control line (for example, do not place the sensor signal line in the same pipe as the strong power line and the control line). IF THEY MUST BE PLACED IN PARALLEL, THEN THE DISTANCE BETWEEN THEM SHOULD BE KEPT AT LEAST 50CM, AND THE SIGNAL ...

Thermal resistance is used to measure the temperature of a substance when its temperature changes, and its resistance also changes with the characteristics of the change. When the resistance value changes, the working instrument will display the temperature value corresponding to the resistance value. RTD sensors use the resistivity of conductors or semiconductors to change with temperature.

1. First, connect the external hardware and install the external COM port of the scanner to the serial port of the industrial computer. 2. The power supply of the SICK scanner control box is 24V positive and negative induction eyes, and the feedback signals of 10, 11 and 12 corresponding to the electric eyes, 24V+, 24V-. ...

1) Long-distance measurement, in the case of no reflector and low reflectivity, it can measure a long distance; 2) There is a synchronous input terminal, which can be measured synchronously by multiple sensors; 3) Wide measurement range and short response time; 4) Compact design, easy to install, easy to operate ...

Visible red LED light source The sensor application of this light source is very common, the light spot is visible, the light spot is large, easy to align, easy to install and adjust, and the price is close to the people, which can meet most applications. The disadvantage is that the detection accuracy is not high. Red laser light source The light of the laser ...

1) The target to be measured: the infrared system is set according to its infrared radiation characteristics; 2) Atmospheric attenuation: When the infrared radiation of the object to be measured passes through the atmosphere, it will be affected by a variety of substances and the attenuation phenomenon occurs; 3) Optical receiver: used to receive part of the infrared radiation and ...

Do you have the following problems in the application of photoelectric sensors? When detecting dark objects (such as black and blue), as long as the detection distance is slightly farther away, even if it is only more than 1 meter, diffuse reflection photoelectric is easy to miss; In the application of the logistics industry, feedback trusses, set ...

Recently, Sick's 3D vision product Ruler series has been newly upgraded! The new products Ruler3002, Ruler3004 and Ruler3010 are officially available today! 　　01. Product characteristics • Contour point upgrade: up to 3200 Data points/Profile • Ultra-high scanning speed ...

1. Measurement Sensors and sensor systems from SICK measure dimensions, oversights, volumes, distances, speeds, and filling levels and then ensure that the process runs smoothly. 2. Detection SICK sensors are able to detect the presence or absence of various objects as well as the quality of consumer products to the satisfaction of ...

Proximity sensors are divided according to their working principle: High-frequency oscillation type, capacitive type, induction bridge type, permanent magnet type, Hall effect type, etc. According to the principle of operation, it can be divided into three categories: High-frequency oscillation type using electromagnetic induction, magnetic force type using magnets, and ...

Overview Identification codes are easy and secure IDM's mobile handheld barcode scanner reliably recognizes 1D and 2D codes, including stacked codes such as PDF417. Depending on the field of application and environmental conditions, a standardized or rugged IP65 degree of protection can be provided.

A photosensor is a sensitive device that responds to or converts external light signals or light radiation. A photosensor is a sensor that uses a photosensitive element (photodiode) to convert an optical signal into an electrical signal. Their sensitive wavelengths are close to those of visible light, including infrared and ultraviolet wavelengths ...

1. In order to have sufficient heat exchange between the measuring end of the RTD and the medium to be measured, the location of the measuring point should be reasonably selected, and the installation of RTD near the valve, elbow, pipe and equipment should be avoided as much as possible. 2. The thermal resistance with a protective sleeve has heat transfer and heat dissipation loss, in order to reduce the ...

(1) Automatic calibration: When the workpiece enters the sensitive area of the probe, hold down the "SET" button for 3 seconds, and the sensitivity value will be set and displayed in green. (2) Two-point calibration: When the workpiece does not enter the sensitive area, press and hold the "SET" button for three seconds.

Since its launch, the SICK ZS36x8 DPM has been well recognized by customers, hitting the pain points of customers for DPM code recognition, and has excellent results in demanding applications in electronics, lithium batteries, automobiles and other industries. 　　In order to better meet the needs of the domestic conventional market and meet the needs of logistics and factory automation.

Photoelectric sensors A photoelectric sensor is a device that converts an optical signal into an electrical signal. Its working principle is based on the photoelectric effect. The photoelectric effect refers to the phenomenon that when light hits some substance, the electrons of the substance absorb the energy of the photons, and the corresponding electrical effect occurs. According to the photoelectric effect ...

1. When the load exceeds the action current, the circuit will be automatically cut off. 2. After the circuit is automatically cut off, the panel indicator light is on, which is convenient for judging the fault part. 3. After troubleshooting, press the red button at the bottom of the panel to restore the normal power supply. 4. For other reasons, the shell ...

1. Parking lot or conveyor and other places Its function is to detect the parking position, and the detection distance is relatively long, which is more applicable in parking lots and other occasions. 2. The position of the processed parts In the factory production process, in order to realize the automatic processing state of the parts, the position of the parts must be inspected.

1. Find the screw at the end of the switch, twist it clockwise to adjust it far, and twist it counterclockwise to adjust it closer. 2. It can increase the intensity of the light source. 3. Improve the sensitivity of the switch sensor. 4. It can also be adjusted according to the instructions for use. ...