Soft Touch/Rorobot Soft Jaw BMC-3B18[P]/S

Introduction:Rorobot BML-3A18[HAS]/S,B-4BG64/S is an external gripper soft jaw, recommended clamping workpiece size (28-50)mm, opening and closing size in (50.4-80)mm, suitable for grabbing steamed cakes, buns, siu mai and jujube cakes and other soft foods, B-4BG64/S ...

Introduction: Rorobot Finger Module B7V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot Finger Module B7V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and ...

Introduction:Rorobot soft claw BMC-4BG64/S, B-4BG64/S is an external gripper type soft claw, the recommended clamping workpiece size is (28-50) mm, the opening and closing size is (50.4-80) mm, suitable for grabbing steamed cakes, buns, siu mai and jujube cakes and other soft foods, B-4BG64/S is ...

Introduction: Rorobot BMC-2015D5/S Features: It can be installed in the Straight Inlet Connection Module [CM] series or the Test-Through Inlet Flange Connection Touch Group [FCM] series Straight-through or side-intake options are available The fingertips are open in the positive pressure state, and the negative pressure ...

Introduction: Rorobot Finger Module B3V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing between the mounting modules is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction:Rorobot Robot Soft Jaw BML-1G364030[HAS]/M, is an enhanced version of the single finger soft jaw, the recommended fingertip and workpiece distance (19-28) mm, the recommended load of one finger soft jaw (0-500) G, the external gripping force (0-11) N. Features: Positive pressure ...

Introduction: Rorobot Flange Connection Module FCM-R08 Features: It conforms to ISO 9409-1:2004 standard (i.e. GB/T 14468.1-2006/) and is suitable for most robot flanges on the market. The maximum load is recommended 20 kg Suitable for non-standard clamps ...

Introduction: Rorobot Finger Module A7V4, Features and Applicable Scenarios: Large clamping force, can be used in series (using screw accessory kit PK) and simplifies the arrangement of the trachea. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the workpiece width is generally greater than 50mm. Product Features ...

Introduction: Rorobot BMC-1G071010/S Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type and non-marking type ...

Introduction: Rorobot soft jaw BMC-3A18 [HAS]/S, soft jaw material is divided into conventional type [H] and non-marking type [HAS] Features: The fingertips are open in the positive pressure state, and clamped in the negative pressure state, it is recommended to use it with a soft-touch air driver, and the fingertip distance of the clamping fingertip G and the external support fingertip distance is D...

Introduction: Rorobot Finger Module C4V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Using Screw Accessory Kit PK) and Simplifies Tracheal Arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: ...

Introduction:Rorobot BML-2G1211[H] Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G The soft claw material is divided into conventional type [H] and ...

Introduction: Soft Touch/Rorobot Finger Module FM-A3V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Finger Spacing and Angle Adjustable, Fixing Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) . ...

Introduction: SoftTouch/Rorobot Connectivity Module CM Series Features: A full range of soft beak modules can be installed at the end Can be mounted on the soft beak series sliding mounting plate [SMP]. Elastic cushioning structure design, especially suitable for multi-layer elastic soft fabric products layered grabbing ...

Introduction: Rorobot BML-3C12[HAS]/S Features: The fingertips are opened in the positive pressure state and clamped in the vacuum state, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by supporting the fingertip distance D. Soft-touch materials are divided into regular [H] and non-...

Introduction: Rorobot Finger Module FM-B4V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixing Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot BMC-2076D5/S Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type and non-marking type, ...

Introduction: Rorobot Soft Jaw BMC-20802 Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G The soft claw material is divided into conventional type and non-marking type.

Introduction: Rorobot Air Driver iPCU 2, with two options: standard iPCU 2-SMN and high-speed iPCU 2-HMN, the high-speed type has a larger flow rate and faster response speed, and is suitable for high-speed handling conditions. Features: With 3 adjustable ...