Rorobot BMC-3A18[HAS]/S The recommended load is 30g

Introduction: Soft Touch/Rorobot Module B-20006/S, B-20006/S is a flexible claw with a small structure, especially suitable for strip and rod workpiece grabbing, which can realize wrapping grabbing, non-trace and non-destructive handling and sorting, to ensure that the product will not be scratched, and reduce the defect rate. When multiple soft jaws are connected in series, ...

Introduction: Rorobot FM-C5V5/LS1 Features: Cooperate with the robotic arm to cope with the flexible production line of small and medium-sized batches and multiple batches in the factory, which can effectively save the production line switching time The maximum opening and closing speed of the soft tentacle claw is 300 times/min, and the highest repeatability is 0.05 ...

Introduction: Soft Touch/Rorobot Quick Change Module QCM-01R, Quick Change Module is used for automatic quick replacement of spare grippers. The quick-change module [QCM] is installed between the flange connection module [FCM] and the end of the robotic arm, and is divided into the robotic arm side (R-side, installed at the end of the robotic arm) and the gripper side (G-side, installed...

Introduction: Rorobot Finger Module FM-B7V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Finger Spacing and Angle Adjustable, Fixing Method: Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot Finger Module B4V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Using Screw Accessory Kit PK) and Simplifies Tracheal Arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: ...

Introduction: Rorobot Finger Module B4V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot Finger Module C5V5, Features and Applicable Scenarios: The module is thinner, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot Finger Module FM-A6V1, Features and Applicable Scenarios: Combination of Two-Finger Module, Compact Structure, Small Footprint. The spacing and installation angle are not adjustable, suitable for clamping tiny, thin and light workpieces, and the fixing method: can be fixed from three directions. Features ...

Introduction: Rorobot Robot Soft Jaw FM-A6V3/LS1, Soft Finger LS1 has good versatility and wear-resistant. It is suitable for rough workpiece surfaces such as food, metal, and plastic parts. When gripping the workpiece, the damage caused to the workpiece by the soft finger itself can be minimized. We...

Introduction: Rorobot BML-4H18[HAS]/S Features: The fingertips are open in the positive pressure state, clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by using the external support fingertip distance D. The soft claw material is divided into conventional type [H and no ...

Introduction: Rorobot BMC-2G1624 [HBAS]/S Features: Clamped in the vacuum state, the fingertip is opened in the positive pressure state, and can be directly driven by the vacuum In combination with a soft-touch air drive (positive and negative pressure switching drive), the clamping workpiece size can be increased Soft...

Introduction:Rorobot Soft Jaw BML-20606, Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G The soft claw material is divided into conventional type and non-marking type, when ...

Introduction: Rorobot Finger Module C8V5, Features and Applicable Scenarios: The module is thinner, and the minimum finger spacing of the installation module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: SoftTouch/Rorobot Quick Change Module QCM-02, Quick Change Module [QCM] is used for automatic quick change of spare grippers. The quick-change module [QCM] is installed between the flange connection module [FCM] and the end of the robotic arm, and is divided into the robotic arm side (R-side, installed at the end of the robotic arm) and the gripper side (G-side, ...

Introduction: Rorobot Soft Jaw BML-1G071010/S Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type and non-marking type ...

Introduction: Rorobot Robot Soft Jaw FM-A6V3/LS1[H], Soft Finger LS1 has good versatility and wear-resistant. It is suitable for rough workpiece surfaces such as food, metal, and plastic parts. When gripping the workpiece, the damage caused to the workpiece by the soft finger itself can be minimized. I...

Introduction: Soft-Touch/Rorobot Skid Mounting Plate SMP-3S Features: It is divided into different styles according to the shape and length of the groove It can be used for assembly between the finger module [FM] and the flange connection module [FCM]. The mounting angle and position of the finger module [FM] can be adjusted freely ...

Introduction: Soft Touch/Rorobot Finger F-B3 Features: The finger material can be selected as regular type, reinforced type [H] and anti-static type [AS]. The reinforced grade [H] has a higher operating pressure range and a gripping force of up to 300% of the fingers of conventional grades. Defend...

Introduction: Rorobot Robot BML-1G071010[LPAS]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted for the distance G between the fingertip and the workpiece. Soft claw material ...

Introduction: Rorobot BML-2G1624[HB]/S Features: Clamped in the vacuum state, the fingertip is opened in the positive pressure state, and can be directly driven by the vacuum In combination with a soft-touch air drive (positive and negative pressure switching drive), the clamping workpiece size can be increased Soft claws ...