The arc of the switchgear cable spacing causes the pressure and temperature in the switchgear to increase rapidly, and if not removed in time, it will cause serious harm in the following aspects:
(1) The arc temperature is twice the appropriate solar temperature, about 10000 °C, because overheating will lead to the melting and gasification of the copper and aluminum bars;
(2) Cable melting, ignition of cable cladding;
(3) Overheating causes the pressure to rise, causing the switchgear to explode;
(4) The switchgear oscillates strongly to loosen the fixed elements;
(5) High temperature cauterizes the skin, and strong light stabs the eyes;
(6) A large amount of harmful gases are generated, damaging the respiratory system;
(7) Plastosis damage to eardrums and lungs;
(8) Debris flying, causing injury or even death.
The degree of damage of arc fault depends on the arc current and the moment of excision, and the energy generated by the arc increases exponentially and rapidly with I2t. Only when the total excision time is less than 85ms, can the equipment not suffer from harm, and if the total excision time is greater than 100ms, it will cause different degrees of harm to the equipment.
|
More on that
|
Precautions for busway installation
1. Requirements for civil engineering before installation
1. The foundation, frame, reserved holes and embedded parts meet the planning requirements of electrical equipment.
2. After the construction of the roof and floor slab, there shall be no leakage.
3. After the indoor above-ground construction is completed, mark the leveling elevation on the wall on the ground.
|
|
Wiener enclosed busbar installation
Closed busway is a busbar system composed of metal plates (steel plates or aluminum plates) as protective shells, conductive strips, insulating materials and related accessories. It can be made into a piercing closing bus with spaced piercing junction boxes, or a feed-in closing bus without a junction box in the middle. ...
|
|
Phase of the busway in the low-voltage incoming line – Wiener
According to the requirements of the relevant specifications, the placement of the three-phase busbar can be roughly divided into two kinds according to the model of the low-voltage distribution cabinet and the different manufacturers: horizontal placement and placement of the down wire, according to the order of placement.
|
|
Standard parameters of busway specification - Wiener
1. The standard scale of the bus duct
This specification regulates the terminology, skill requirements and test methods of the insulated bus trunk system (bus duct) and its plug-in feed box (hereinafter referred to as the feed box).
This specification specification applies to additional voltage AC to 660V...
|
|
The application of Wiener bus system wiring technology in box transformer
The bus system is to directly connect the components to the bus, the bus does not need to be perforated, at this time, the bus is not only the conductor of the component, but also the support of the component, the current can reach 2500A, so that the box transformer function has the following progress:
1 ...
|
|
Advantages of cable tray installed in busway
At the time of the cable tray installation, the wiring is not very convenient. This phenomenon can be avoided by using busway. The 5 advantages of using busway in the cable tray device are as follows:
1. Convenient connection of bus duct: the so-called plugging ...
|
|
The connection method of the tubular busbar
In the industry, tubular bus bar can be described as one of the more common equipment, with high mechanical strength, good insulation, wide range of application and other characteristics of many enterprises. So do you know what are the ways to link tubular busbars?
...
|
|
Application of busway – Wiener
The busway system is an efficient power distribution device, especially suitable for the needs of high-rise buildings and large-scale factories for reasonable wiring. With the presentation of modern engineering equipment and equipment, the electricity consumption of all walks of life has increased rapidly, especially many high-rise buildings and large factories. Traditional cables serve as ...
|
|
The technology of the main bus bar in the low-voltage open light cabinet - Winer
One of the characteristics of the Wiener low-voltage switchgear is the multi-functional busbar system. The bus bar is a conductor that connects large electrical equipment such as generators and transformers with various electrical devices. The role of the bus bar is to transmit electric energy with the, and the bus bar is the main equipment constituting the electrical wiring. ...
|
|
Mesh tray reduces the cost of replacing cables – Wiener
(1) Simple maintenance and repair operations
Equipment is often added or removed or changed in the computer room, and cables are removed or added at the same time, and the grid bridge with open structure can observe the cables to the maximum extent, so it is easy to distinguish the cables that need to be replaced, so that maintenance and repair ...
|
|
Introduction to Laminated Busbar System – Wiener
In the power system, the bus connects the various current-carrying branch circuits in the power distribution device together, and plays the role of collecting, distributing and transmitting electric energy; According to the appearance and structure, the bus bar is roughly divided into three categories: hard busbar, soft busbar and closed busbar.
...
|
|
Low-voltage dense busway uses and applications
Densely insulated bus duct (hereinafter referred to as bus duct) can be communication three-phase three-wire, three-phase four-wire, three-phase five-wire system, frequency 50-60Hz, voltage to 400V, rated operating current of 250-5000A, mainly as a new type of power supply and distribution equipment in industrial and mining, enterprises and high-rise buildings. Mother with insertion day ...
|
|
The common DC bus of the inverter system - Wiener
1. Three-phase AC power supply inlet
The power input of each inverter is connected in parallel on the same AC bus, and the power supply phase of the input of each inverter is consistent. In Figure 3, the circuit breaker QF is the incoming protection device for each inverter. LR is an incoming reactor, when multiple inverters are in the same ...
|
|
Conductor and bus welding requirements - Wiener
1. Before welding, it is necessary to check whether the welding equipment is defective, whether the grounding of the electrical equipment is reliable, and strictly abide by the "welder safety operation procedures" when welding.
2. Correct wires and busbars, and prohibit the use of handleless files.
...
|
|
Corrosion type of tubular busbar - Wiener
1. Crevice corrosion
When there is a gap between the surface of the tubular bus itself and other things, the corrosion in the gap will be accelerated due to the difference in the effect of the inflatable battery, but there is no effect on the outside of the gap. However, crevice corrosion has little to do with the type of alloy, because even very corrosion-resistant ...
|
|
Classification of the use of busway in different places - Vernal
(1) General bus duct
Non-flame retardant and non-fire-resistant bus duct selected for general load power distribution. In the event of a short circuit, it will be incinerated until it is connected to other busbars, which can easily cause fire accidents.
(2) Flame retardant bus duct
...
|
|
Wiener is a common way to wiring busbars
Single bus wiring method: all outgoing wires are connected to the same busbar, which is also the most cost-effective and simplest wiring method
Single bus segmentation: The outgoing line is arranged in two parts on different sections of the single busbar, so that a power failure in the meantime does not affect the power supply of the other bus
...
|
|
Busway installation method - Wiener
1. Busway horizontal device, the interval between the two brackets is ≯2500mm, and the interval between straight devices is ≯3600mm;
2. When the device bracket is straight, it should be drilled with the channel side plate and fastened with M6-M8 bolts.
3. In the process of installation construction, priority should be given to the power supply system, ...
|
|
Distribution cabinet bus connection method - Wiener
When users use the distribution cabinet, they must understand the circuit device of the busbar, and many users are not very well understood, so let's talk about the bus connection mode of the distribution cabinet.
The bus bar is used for the internal and external electrical appliances of the distribution cabinet.
|
|
A brief introduction to the classification of busway - Wiener
Busway (referred to as busway) is a busbar system composed of metal plates (steel plates or aluminum plates) to protect the shell, conductive bars, insulating materials and related accessories. It can be made into a plug-in closed bus with plug-in junction boxes at intervals, or as a feed-in type without a junction box in the center ...
|
|
Contact
working hours
