Precautions for busway installation

Create Date: 2024-8-30 12:03:23|Source: Woehner/Wiehner

1. Requirements for civil engineering before installation

1. The foundation, frame, reserved holes and embedded parts meet the planning requirements of electrical equipment.

2. After the construction of the roof and floor slab, there shall be no leakage.

3. After the indoor above-ground construction is completed, mark the leveling elevation line on the wall.

4. The strength of the base and frame to reach the permissible device.

5. The renovation project of the mother lane that may damage the device is completed.

6. There should be anti-theft measures in the relevant directions of the device bus duct.

Precautions for busway installation

2. Personnel selection and training before the device

1. Preparations for the bus duct device: the installation, operation and maintenance of the trunking should be carried out by professional employees.

2. Professional workers should understand the installation, construction, operation and hazards of the equipment: they should also be trained in how to power the power supply and test the equipment system.

3. Operation of bus picking device

1. According to the information recognized by the manufacturer and the customer. Such as the original drawings, direction maps, remove obstacles, reserve directions.

2. Generally, the size of the reserved hole should be 50mm -100mm larger than the size of the dense aluminum bus duct. Special data refer to the drawing requirements.

3. The distance between Siemens busway and the wall and the flowering board must ensure that the busway is closed with high strength during installation and maintenance, and there is a satisfying horizontal and straight space.

4. Take preventive measures to avoid corrosion of leakage, dust and heat sources on the dense aluminum bus duct. From: House of Electrotechnical Technologies

5. Manufacture of bus duct device hanger: first confirm the orientation, use a thin wire to pull the simulated direction, fix the device bracket, and pay attention to whether the fixation of the device bracket is strong, high-voltage collinear bus duct, and the structure of the building will not be damaged.

6. Conduct insulation tests on the densely covered aluminum bus duct unit of the general device, and the detection value can only be installed within the qualified range.

7. When hoisting, the waterproof bus duct must pay attention to personal safety and equipment safety precautions. Avoid injuries and damage to dense aluminum busway.

8. When the straight device is straight, there is no special situation, and the device is generally from bottom to top section by section; Effective protection measures must be taken for the densely packed aluminum busway that has been installed to avoid the intrusion of foreign bodies.

More on that

	Advantages of busbar mounted electrical equipment - Wiener The novelty, flexibility and originality of the busbar device appliance. It indicates the vitality of this skill and its broad market prospects. This is the real reason why we pay attention to it. First of all, this small electrical appliance set ...
	NH-Fuse Type Disconnector Instructions for Use When switching on and off components, you should pay attention to the following: –In accordance with VDE-0105-100, only operation by electrical professionals or persons with electrical knowledge is allowed (operation without electricity, closing, disconnecting, and replacing fuses ...).
	What are the modules of the Wiener bus system? The modulus of the bus system is 40mm, 60ram, 100/185mm; The bus cross-section is rectangular, double "T" (i.e., "H" shape) and three "T" (i.e., 'state') shapes; The bus system can be three-wire, four-wire or five-wire, or even seven-wire, of course, it should be determined according to the needs ...
	Use and characteristics of AC busbar systems – Wiener The communication and connection skills of the independent power supply system create better prospects for the power supply of the future. Hundreds of systems around the world have installed SMA's Sunny Island battery inverters to supply power to customers for a long time. The stackability of Sunny Island, i.e. multiple Sunny Islands ...
	Introduction to Laminated Busbar System – Wiener In the power system, the bus connects the various current-carrying branch circuits in the power distribution device together, and plays the role of collecting, distributing and transmitting electric energy; According to the appearance and structure, the bus bar is roughly divided into three categories: hard busbar, soft busbar and closed busbar. ...
	What are the hazards of 220V DC in the bus system - Wiener The grounding of the DC system should include two situations: the one-point grounding of the DC system and the two-point grounding of the DC system. In the DC system, the positive and negative poles of DC are insulated from the ground, and there is no grounding current when generating a ground current when one pole is grounded.
	Difference Between Busbar and Cable – Vernal When the busway has not been developed and introduced, the cable is still an indispensable figure in the low-voltage distribution system, when the busway system is introduced and widely used. Whether to choose the cable or the bus duct has become a topic of endless debate. So it's hard to say which of the two is better ...
	Low-voltage cabinets need temperature and humidity controllers for the reason - Vernal Why is the temperature and humidity controller of the low-voltage cabinet? The application field of low-voltage cabinet is very wide, high-voltage switchgear should be one of the key electrical equipment and equipment for electromagnetic energy production scheduling and transportation, there will be some simple reasons to form high-voltage switchgear hot in specific work, low-voltage cabinet I remind you that at this time ...
	Closed busway essentials – Wiener Before the closed busway device, it should be ensured that the electrical shaft, the transformer and distribution room, the decoration project of the place through which the busway passes, and the heating and ventilation project are all completed to ensure that the closed busway is not polluted. The reserved holes and embedded parts of the floor and wall should be embedded and reserved according to the position required by the design. ...
	The advantage of intelligent energy-saving dense busway - Wiener Intelligent, energy-saving, dense busway, it is capable of generating outward electromagnetic wave radiation. It can be said that the line loss in the process of power transmission is greatly reduced, which can save energy and reduce electromagnetic radiation pollution. In addition, the product is also specially equipped with a radiator, which increases the heat dissipation area of the conductive bar and accelerates the ...
	Wiener looks at the busway drawing method First, in the CAD system drawing, it is a plan of the bus duct, and two parallel polylines can indicate the bus duct. 2. The busway includes the following parts: 1. Feeder busbar, which is used to transmit electricity 2. Plug-in busbar with plug-in interface above, ...
	How is the Wiener bus system generally debugged in sections? Bus refers to the connection of voltage distribution devices at all levels in the substation, as well as the connection of electrical equipment such as transformers and corresponding distribution devices, most of which use bare wires or stranded wires with rectangular or circular sections. The role of the bus bar is to collect, distribute and transmit electrical energy. According to the structure, the bus bar is divided into hard busbar, soft ...
	Introduction to the classification of busway - Wiener According to the different uses of the bus duct, the bus groove is generally composed of the start bus slot, the straight bus slot (no partition jack and jack), the L-shaped straight (horizontal) curve bus, the Z-type straight (horizontal) offset bus, the T-shaped straight (horizontal) tee bus, the X-type straight (horizontal) cross-way bus, the variable ...
	Wiener Electric's busbar system escorts the operation of textile machinery equipment According to Wiener electrical engineer, the bus system is a process-assisted component, the main effect is to hook the switch on the adapter, and the adapter is then hooked on the copper bar, so that the full protection of the copper bar can be completed, and the safety factor is improved; The upper port of the switch can be connected without ...
	The difference between metal busbar and closed busbar - EVOC The nature is different Busbar: It is a common path on which multiple devices are connected in the form of side-by-side branches. Busway: It is a closed metal equipment composed of copper and aluminum busbars. Different uses Mother...
	The role of the busbar in the excitation system – Wiener The bus PT is used to measure the bus voltage on the high-voltage side of the main transformer, and is used to assist in grid connection. Before starting the synchronous grid connection, the excitation system actively adjusts the terminal voltage according to the bus voltage measured by the bus PT, so that the voltage on both sides of the grid-connected switch is basically equal, which is convenient for the same period of grid connection. ...
	Difference Between Fuse and Circuit Breaker – Vernal The principle of the fuse is to use the current to flow through the conductor to heat the conductor, and the conductor is ablated after reaching the melting point of the conductor, so the electrical appliances and circuits used for circuit maintenance are not burned out. It is an accumulation of heat, so it is also able to complete overload maintenance. Once...
	Connector box features of the busbar system – Wiener 1. Rapid device Today, busway adapters cannot be flipped at the time of installation, and the two busway sections are not out of phase when flipped when connected. 2. High protection level The coupling box has a protective function, ...
	Introduction to the advantages of busway - Wiener The advantage of the busway is that its structural design is simple, it is composed of metal plates, which can connect the circuits together, so as to achieve the safe and reliable transmission of electric energy. In addition, its structural design can effectively assist in reducing the occurrence of short circuits, reducing heat loss, and can effectively ensure the power ...
	A new product has been added to the world of CrossBoard® systems A new addition to the world of CrossBoard® systems: the MOTUS® hybrid motor starter with IO-Link interface is a new networking feature in the MOTUS® IO-Link family that enables continuous communication between the control and device levels. Control the delivery of instructions, control the parameters ...