When the differential pressure flowmeter (V-cone flowmeter) is used in the field, it often encounters such and such problems, but to investigate the reason, as long as it is installed correctly, the primary problem is to appear on the secondary surface differential pressure transmitter.
1. The output of the differential pressure transmitter is too low
The primary reasons are: leakage or blockage of the positive pressure pipe, excessive range of the differential pressure transmitter, and too small flow in the pipeline. For the general measurement of fluids, it is impossible for the impulse pipe to leak or block, and the normal thing to produce this phenomenon is to measure the gas or impurities on the spot, as long as we check the impulse pipe, sweep away the blockage, adjust the differential pressure transmitter range and adjust the process flow. Taobao Special Sale Mall Red Blood Tape Taobao Breast Enhancement Product Ranking Hydrating and Fine Lines Eye Cream Ranking Slimming Face Hydration Moisturizing Which Brand Is GoodVery Good To Remove Dark Circles What Brand Of Eye Cream Is Good Recommended Sharing Community
2. The output differential voltage is too high
This primary reason is the opposite of the above, and we can refer to the above solutions to sweep them one by one.
3. The output differential pressure is unstable and fluctuates greatly
The installation direction is incorrect, the upper and lower valve disturbances and the impact of the elbow on other chokeholders are the most influential to save components, which requires us to adjust the process or change the installation location.
|
More on that
|
The difference between inverter motor and ordinary motor – Reynolds
Inverter motor - used for special occasions with inverter, it is different from the general motor in that a strong cooling fan is added. And the power of the fan comes from the independent power supply, can not be from the main motor out of the line, the effect of the strong cooling fan is to ensure that the motor at low speed...
|
|
There will be problems with the inverter left for a long time - Reynolds
Most inverter brand products can rely on the heat generation of internal electrical components to remove moisture during normal use. If you don't have to do it for a long time, it's easy to get wet. The chip pins, penetrating resistors, capacitors, and inductor pins of the DIP package will be severely rusted or desoldered, resulting in on-resistance ...
|
|
Use the right power for the inverter – Reynolds
Low pressure issues
The VFD reports a low voltage glitch when the drive's DC link voltage drops below 62% of the nominal level at the high setting (480 Vac) and 50% of the nominal value at the low setting (400 Vac).
The +10% and -15% voltage tolerances in most manuals are the ones that claim to be ...
|
|
Protection feature of overcurrent trip - Renol
1. Maintenance objectives of overcurrent
In the frequency conversion speed regulation system, there are two devices: the frequency converter and the motor. The degree of tolerance to overcurrent is not the same. The planners of the production machinery decide on the capacity of the motor based on the principle of heat. That is, as long as the electricity ...
|
|
Reynolds inverter FAQ - parameter class
1. What are the factory parameters of inverter rehabilitation?
N600 = 100 (often press the WR button for 3-5 seconds), it is necessary to be in the shutdown state to be effective.
2. In the parameters of the N308 motor of the inverter, [motor leakage inductance reactance] is the specified sub...
|
|
Features of the unit tandem inverter - Reynolds
(1) The multi-pronged PWM control method is selected, and the output voltage waveform is close to the sine wave.
(2) The rectifier circuit is multiplied, the number of pulses is as high as 36, the power factor is high, and the input harmonic is small.
(3) Modular design, compact structure ...
|
|
Difference Between Soft Starter and Inverter – Reynolds
Soft starters and frequency converters are two completely different products. The inverter is used in the local area where speed regulation is required, and its output not only changes the voltage but also changes the frequency at the same time; A soft starter is actually a voltage regulator, which is used when starting a motor, and the output only changes the voltage and does not change the frequency. Change...
|
|
Precautions for installation of Reynolds low-voltage inverters
One. Safety Precautions
1. First of all, it is necessary to have certain electrical professional knowledge, and understand the job site, understand the equipment status, and have certain electrical operation technology.
2. Determine the voltage level of the equipment (such as low-voltage AC380V) and whether it is low-voltage ...
|
|
Reynolds drives use the most energy-efficient method
As an electronic electric, the inverter itself also consumes electricity (about 3-5% of the additional power). A 1.5 hp air conditioner consumes 20-30W of electricity, which is equivalent to the length of a lamp. The inverter works under the power frequency and has the function of saving electricity, which is practical.
But the conditions are:
At the top of the list, great success ...
|
|
Reynolds product range models
JJR1000系列：
JJR1011；JJR1017；JJR1022；JJR1030；JJR1037；JJR1045；JJR1055；JJR1075；JJR1090；JJR1115；JJR1132；JJR1160；JJR1200；JJR1250；JJR1 ...
|
|
Common faults and solutions of vector inverter - Reynolds
The following faults may be encountered during the use of the inverter, please refer to the following methods for simple fault analysis:
1. No manifestation at power-on:
1) Use a multimeter to check whether the input power supply of the inverter is consistent with the rated voltage of the inverter, and check the cleaning problem.
2） ...
|
|
Introduction to the function of the inverter - Reynolds inverter
In power distribution equipment such as voltage distribution cabinets and switchgear at all levels of power plants and substations, the conductors connected between large electrical equipment such as generators and transformers and various electrical equipment are called busbars. Busbars, also known as busbars, are used to collect, distribute, and transmit electrical energy. The connection methods of the bus bar are ...
|
|
Fault analysis of short circuit of inverter motor – Reynolds
According to the different degrees of short circuit, the inverter can display the short circuit of the SCF1 motor; SCF2 has an impedance short circuit; SCF3 is short-circuited to ground.
Causes of the problem: insulation problems with the cable from the motor or inverter to the motor; current transformer fault; ...
|
|
Frequency characteristics of Reynolds frequency converters
a. Output frequency scale. The output frequency scale that can be controlled by the general inverter, the lowest starting frequency is generally 0.1Hz, and the highest frequency is different according to the functional indicators of the inverter, generally 400Hz, and some models are 650Hz. No matter how high the output frequency is, it depends on the scale of the high-frequency inverter.
...
|
|
Operating instructions for the Reynolds control panel
1. FUN button; Press the FUN button to enter the settings menu F00;
2. Press and hold the up button or down button to scroll to the code that needs to be set;
3. Press the FUN button to confirm at this moment, and adjust the entry parameters to the required value;
4. After the adjustment is completed, press the WR storage button, and then the panel will display the ...
|
|
PLC and inverter communication mode
1. The switching signal of PLC controls the inverter
The PLC can control the start, stop and reset of the inverter through the program; It can also control different combinations of high-speed, medium-speed and low-speed terminals of the inverter to achieve multi-stage speed operation. However, because it is controlled by switching ...
|
|
Introduction and features of Reynolds soft starters
Reynolds soft starters include soft starters for high, medium and low voltage motors, including JJR1000 series, JJR2000 series, JJR5000 series, and RNB3000 series frequency converters. Reducing the starting power supply avoids voltage drops and voltage dips in the power supply. Smooth start-up avoids product damage. ...
|
|
Applications of Reynolds frequency converters
A frequency converter is a power electronic device that can change the frequency of an AC power source to control the speed and output power of a motor. Inverters are widely used in industry, aviation, metallurgy, petroleum, chemical industry, electric power and other fields.
|
|
Small fan inverter choice - Reynolds
Now many electrical appliances are advocating the use of small parts, because small parts will not occupy space, and small parts can be moved and overhauled at any time, and the inverter also has a small inverter, how to buy a small fan inverter?
Power picking
...
|
|
Wiring method and principle of PLC and inverter shielded wire - Reynolds
In order to avoid the interference of the control signal line between the PLC and the inverter by the space electromagnetic field, the shielding wire can be connected to the outer layer of these control signal lines to improve the anti-interference ability of the system. This kind of wiring must be noted, and only one point can be selected for the grounding point of the shield. Whether it's on the PLC side, or ...
|
|
Contact
working hours
