1. What are the factory parameters of inverter rehabilitation?
N600 = 100 (often press the WR button for 3-5 seconds), it is necessary to be in the shutdown state to be effective.
2. In the parameters of the N308 motor of the inverter, is the specified sub-leakage inductance reactance or rotor leakage inductance?
Stator leakage reactance = rotor leakage reactance = motor leakage reactance
3. Can the inverter check the previous fault information?
Yes, for example RNB6000 it is possible to check the last 8 faulty code information through parameter N603.
4. RNB6000 the N701-N712 parameter specification, but I can't see it in the inverter?
N701-N712 is the default hiding group parameter, set N700=7
5. RNB6000 the parameters of the motor should be entered correctly before starting?
Because the RNB6000 inverter completes the better control of the motor inside the motor, and a special algorithm is added to achieve better control effect, so it is necessary to correctly input the parameters on the motor sign. Otherwise, there will be a phenomenon such as starting over the current or the frequency cannot be increased.
6. How to set the external analog input of RNB6000 inverter 0-20MA and 4-20MA?
RNB6000 type can input 0-20MA and 4-20MA externally, after the internal parameter N222=0% is 0-20MA input, N222=25% is 4-20MA input.
7. Can the RNB6000 inverter complete the given switching between the main frequency and the auxiliary frequency source?
The RNB6000 type inverter is perhaps connected to the external terminal X1 (12). X2 (13) terminals. The X3(14) terminal completes the frequency switching by binary combination (e.g., parameter N203=15.N204=16.N205=17). The default frequency is given by N002 and can be switched when the multi-function terminal is connected to the COM(20) terminal (the priority of the terminal is higher than that of N002).
8. What is the difference between the RNB6000's motor tuning N311=1 (static self-learning) and N311=2 (dynamic self-learning)?
RNB6000's N311=1 static self-learning learns the resistance and resistance leakage inductance of the motor, and rewrites the internal parameters N306.N308.N309. values, and N311=2 dynamic learning is self-learning of the no-load current and motor mutual inductance of the motor, and rewrites N307.N310.N403, and the parameters of dynamic learning are more comprehensive (it is recommended to use the method of dynamic learning).
9. How to set the analog output of RNB6000 inverter to 0-10VDC, 0-20MA and 4-20MA?
THE RNB6000 CAN OUTPUT 0-10VDC AND 0-20MA/4-20MA OUTPUT SIGNALS EXTERNALLY, AND THE HARDWARE PART IS SELECTED BY TWO DIP SWITCHES ON AM1 AND AM2 ON THE MOTHERBOARD (CURRENT/VOLTAGE IS SELECTED), AND THEN THE 0-20MA OUTPUT IS SET TO 0% WHEN THE PARAMETERS N226 (AM1 CHANNEL) N228 (AM2 CHANNEL) ARE SELECTED. 4-20MA OUTPUT: 25%.
10. How to complete heavy-duty control (vector control) of RNB6000-type inverter.
To complete the vector control, you need to correctly input the parameters on the motor name plate (motor current, speed, pole pair), and then put N311=2 (dynamic self-learning), and then take the empty motor, start (inverter start learning) to identify the motor parameters, after learning, and then N008=4 can be.
11. How many relay dry contact outputs are supplied to the RNB6000 inverter?
The RNB6000 type is supplied with two relay dry contact outputs, which are 11.21 (NO point), 01.02.03 (normally open, normally closed) outputs, and one transistor output.
|
More on that
|
DCS and PLC and other control cabinets are inspected before leaving the factory
1. Test preparation:
1. It is necessary to remove all power switches before powering on the PLC control cabinet or IO cabinet.
2. It is necessary to completely cut off the connection between the PLC or DCS card and the outside. All front adapters are to be loosened and raised.
3. Check the power terminal wires and connectors.
|
|
"RNB6000 frequency conversion governor" was included in the National Torch Program
Recently, in the "2012 National Torch Program Project" issued by the Ministry of Science and Technology of the People's Republic of China, the "RNB6000 Frequency Conversion Governor" independently developed by Reynolds was included in the "2012 National Torch Program Project" with its domestic leading skills and efficient energy-saving conversion power.
|
|
Indicator of Reynolds inverter cabinet wiring
Voltage level: The voltage level should match the voltage level of the power supply and motor to ensure electrical safety and normal operation of the equipment.
Current level: The current level should match the rated current of the motor to ensure electrical safety and normal operation of the equipment.
Cable Specification: Cable ...
|
|
Reynolds inverter power selection
The system power is equal to the product of the power of a general-purpose inverter and the power of the motor. As long as both work efficiently, the system power will be higher. From the perspective of power, when choosing VFD power, you should pay attention to the following points:
VFD ...
|
|
Frequency converter overcurrent problem treatment - Reynolds
General treatment methods for inverter overcurrent problems:
The output side of the inverter is a PWM voltage waveform, and after passing through the motor winding, the output current is approximately a sine wave, and lags behind the voltage by a phase viewpoint, which is determined by the power factor of the motor. The output current of the inverter passes through ...
|
|
Introduction to the key components of the inverter - Reynolds
There are many kinds of components of the inverter, different components have different functions, and different components have different specializations! In addition to the composition and application of Aideley inverter, there are also key components of inverter to provide for the operation of inverter.
|
|
Advantages of frequency converters over soft start – Reynolds
(1) The starting torque is large and the power factor is high. Because the power factor of the motor is related to the working frequency, the power factor under the power frequency power supply is much lower than that under the low-frequency power supply when the motor is running at low speed. The inverter can control the motor from low frequencies and ...
|
|
Frequency converter soft troubleshooting – Reynolds
Undervoltage is also a problem that we often encounter in application. Mainly because the voltage of the main circuit is too low (220V series is lower than 200V, 380V series is lower than 400V), the main reason: a certain way of the rectifier bridge is damaged or there is abnormal operation in the three ways of the thyristor, which may lead to the appearance of undervoltage problems, ...
|
|
Operating procedures for Reynolds frequency converters
Bypass cabinet: The cabinet is equipped with high-voltage inlet and outlet isolation switches QS1 and QS2. Among them, QS1 is a single-pole single-throw variable frequency incoming knife switch, and QS2 is a single-pole double-throw power frequency and variable frequency outgoing knife switch. The bypass cabinet is a high-voltage environment, please investigate the status of the live display and electromagnetic lock to ensure safety before ...
|
|
PLC and inverter communication mode
1. The switching signal of PLC controls the inverter
The PLC can control the start, stop and reset of the inverter through the program; It can also control different combinations of high-speed, medium-speed and low-speed terminals of the inverter to achieve multi-stage speed operation. However, because it is controlled by switching ...
|
|
Reynolds inverter parameter problem
1. What are the factory recovery parameters of Reynolds inverter?
N600 = 100 (often press the WR button for 3-5 seconds), it is necessary to be in the shutdown state to be effective.
2. In the parameters of the N308 motor of the inverter, is the [motor leakage inductance reactance] specified sub-leakage inductance or rotor leakage inductance react?
Decide...
|
|
Inverter control loop wiring taboo - Reynolds
1. The wires laid out in the inverter control circuit should be separated from the main circuit cable (power line), so as to avoid the harmonic disturbance components on the side of the main circuit of the inverter from polluting the inverter control circuit;
2. Due to the faulty signal of the inverter and ...
|
|
The main failure mode of mechanical parts – Reynolds
The top failure modes of mechanical parts:
Failure: The mechanical part cannot complete its normal function within the planning and booking period and under the regular conditions.
Ways in which mechanical parts fail: overall cracking, plastic deformation, corrosion, abrasion, gluing, and touch exhaustion
General ...
|
|
Precautions for installation of Reynolds low-voltage inverters
1. Safety precautions
1. The primary requirement is to have certain electrical professional knowledge, and understand the job site, understand the equipment status, and have certain electrical operation technology.
2. Determine the electrical ...
|
|
Wiring of Reynolds frequency converters
1 Main circuit wiring
(1) Reynolds inverter three-phase AC input terminal (R, S, T)
The power input terminal is connected to the three-phase AC power supply through the circuit breaker of the circuit breaker for line protection, regardless of the connection phase sequence. It should be noted here that the three-phase AC power supply is not ...
|
|
The abnormal installation of the inverter in the power frequency motor leads to hazards
Installing a variable-frequency drive (VFD) on the power frequency motor can complete the precise control and speed regulation of the motor, and improve the power and accuracy of the progressive motor. However, if it is not properly used and used, the following damages may occur:
...
|
|
Reynolds soft starter troubleshooting methods
Common troubleshooting methods for Reynolds soft starters.
During the debugging process of the soft starter, the fault light is on, the motor is unresponsive, and the cause of the fault is analyzed:
When the starting mode adopts the live mode, the operation sequence is wrong (the correct operation sequence must first deliver the main power supply, and then the control ...
|
|
The factor that causes the breakdown of the inverter – Reynolds
1. Overpressure leads to brake pipe breakdown.
The so-called overvoltage of the inverter refers to the fact that the inverter voltage formed due to various reasons exceeds the additional voltage, which is concentrated in the DC voltage of the inverter DC bus.
The overvoltage alarm generally appears at the time of shutdown, and its main ...
|
|
Characteristics and Discrimination of Resistance Damage - Reynolds
I often see many beginners tossing on the resistor when overhauling the circuit, and it is dismantling and welding, in fact, it is repaired a lot, as long as you understand the damage characteristics of the resistor, you don't have to bother.
Resistors are the most numerous in electrical equipment ...
|
|
Calculation of the braking resistance of the inverter – Reynolds
After selecting the resistance value of the braking resistor, the power value of the braking resistor should be confirmed, and the selection of the braking resistor power is relatively cumbersome, and it is related to many factors.
The instantaneous power consumed by the braking resistor is calculated according to the following formula: P instantaneous = ...
|
|
Contact
working hours
