Advantages of OTC welding robots:

The whole process of arc welding is much more complicated than the whole process of butt welding, and the special tool positioning point (TCP), that is to say, the track of the edge of the welding rod, the attitude of the welding machine, and the main parameters of electric welding are all operated regularly; Therefore, in addition to the general effect mentioned above, the welding robot for arc welding must also have ...

The robot vision system is generally composed of optical systems (light sources, lenses, industrial cameras), picture acquisition units, picture processing units, actuators and human-machine interfaces and other modules.

1. Improve the authority of the robot to handle: Turn on the power supply of the robot control box and enter the main interface of the teach pendant: As shown in the figure above, press to enter the R function code interface, enter 314, and then, enter the authority password 12345, and then. You can carry out the robot handling operation. ...

Industrial robot is an organic combination of machinery and computer program products, not only can save labor, but also has the advantages of sensitive and accurate, fast and efficient, and stable system. There are always some aspects to pay attention to when developing high-performance industrial robots.

The maintenance content of the robot is mainly to replace the smooth oil of the six shaft reducers and the smooth oil of the J4 shaft gear shaft, the replacement of wearing parts, the operation status of each module in the control cabinet, and the wear and tear of each cable in the control cabinet. Not changing the oil for a long time ...

1. Number of joints. The number of joints can also be referred to as degrees of freedom, which is an important indicator of the robot's flexibility. Generally speaking, the robot workspace can reach three degrees of freedom, but welding not only needs to reach a certain orientation in the space, but also needs to ensure the spatial posture of the welding gun. ...

The servo motor is the driving device of the robot joint The joint drive of the robot is inseparable from the servo system, and the more joints, the higher the flexibility and accuracy of the robot, and the more servo motors need to be used. The servo motor affects the robot's arm control, such as orientation, angle, etc.

The difference between robotic palletizing and depalletizing is that they perform different tasks. Palletizing is the safe stacking of objects together, while destacking is the unpacking of previously stacked objects. Both of these features can improve the output power and reduce the manpower input, and together they also reduce the operational risk and ...

Work space refers to the orientation mobilization of a specific part of the robot arm under certain conditions. The nature and size of the workspace reflect the size of the robot's working capacity. When understanding the robot's working space, pay attention to the following: ...

1. Stable center of gravity Welding is like practicing martial arts, the first thing to do is that the chassis should be stable, that is, the "horse step" should be stable, and the center of gravity cannot be unstable, and it is difficult to weld a good weld when the welding is shaking. 2. The welding torch should be stable Trembling words ...

Fault phenomenon: the manual operation is normal, after the automatic form is converted, the red light in the stop state does not go out, but press strat (start) once, and the program takes a step. Solution: Ask the manufacturer for the treatment method, and the reason is that the operation mode of the machine has been changed to stop in one step (1STEP). ...

OTC Odichi robot has a very good advantage in welding use, and in the welding robot under OTC, there are two different types of welding robots: 6-axis and 7-axis. So what is the difference between a 7-axis welding robot and a 6-axis welding robot in use? Let us go through this ...

The general welding equipment is completely controlled by manual experience, so that the solder joints of the nut are high and low, and the output and power stability of the equipment are not ambitious, and the false welding phenomenon simply occurs. When welding nuts with general welding equipment, it is very simple to ...

OTC seven-axis industrial robot Japan's DAIHEN Group Odihi has launched the latest seven-axis robots (FD-B4S, FD-B4LS, FD-V6S, FD-V6LS, FD-V20S). Thanks to the rotation of the seventh axis, they are able to complete tasks like ...

Six-axis industrial robot is a commonly used 6-joint industrial robot in practice, six-axis robotic arm, six-joint manipulator, six-axis robotic arm, robotic arm, etc. are its name, industrial robots generally refer to four-axis, five-axis, six-axis manipulator. The joint structure of each robot ...

The robot welding uses argon-rich mixed gas maintenance welding, and the welding defects presented in the welding process generally include welding deviation, undercut, porosity, etc., the specific analysis is as follows: (1) The welding deviation may be due to the incorrect orientation of the welding or the problem of finding the welding gun. At this time, consider T...

1. The wire feeder is divided into two types: integrated and separated. The wire feeder is installed on the rear of the upper arm of the robot and is integrated with the robot; The wire feeder and the robot are separated from each other. Because the distance from the integrated wire feeder to the welding gun is more than ...

Fault phenomenon: Manual operation is normal. After switching to automatic mode, the intermittent red light does not stop, but pressing strat once will make the program trek one step. Solution: Because the working mode of the machine is changed to one step intermittent, please ...

From the perspective of movement mode, parallel robots can be divided into plane organization and space organization; Subdivisions can be divided into planar moving organizations, planar moving rolling organizations, spatial pure moving organizations, spatial pure rolling organizations and spatial mixed motion organizations, and can also be classified according to the number of degrees of freedom of parallel organizations: ...

1. Pressurization adjustment The pressure of the wire feeding roller should be adjusted appropriately according to the diameter of the wire used. If the pressure is insufficient, the wire will slip; If the pressure is too high, the welding wire will be cut and deformed. If the cored wire is used, the wire feed wheel is pressurized ...