A few things to note about the installation of the RKC thermostat

Create Date: 2024-8-30 12:03:23|Source: RKC

1) For RTD input, 3 wires with low resistance and no difference should be used.

2) The input signal line should be far away from the power line of the instrument, the power supply line and the load line to avoid noise and annoyance.

3) The power cord of the instrument is generally annoyed by the power supply.

4) When the instrument makes up for the external noise annoyance, it is necessary to use a clutter filter.

5) Equip the noise filter on the surface board and connect it to the ground, and reduce the wiring distance between the noise filter output and the power terminal of the instrument.

6) Do not use the fuse and switch at the output of the filter to reduce the effect of the filter.

7) After the power is turned on, it takes 5-6 seconds to prepare the surface output by the relay, such as when it is used for external connection loops and other signals, please use the delay relay at the same time.

8) This instrument has no power switch and fuse, assuming that the demand can be installed Recommended fuse specification: rated voltage 250V rated current 1A Fuse type: delay fuse.

9) Do not overtighten the terminal screws. In addition, suitable terminal screw lugs are used.

A few things to note about the installation of the RKC thermostat

More on that

	RKC thermostat - common faults and solutions of temperature control instruments 1. Heating for a period of time, the temperature does not change. The ambient temperature of the site (e.g. room temperature 25°C) is displayed at all times. In case of such failures, first check whether the SV value setting value is set, whether the 0UT indicator light of the meter is lit, and whether the No. 3 and No. 4 terminals of the meter with the "multimeter" are 12VD ...
	What are the precautions for the installation of the RKG thermostat? 1) For RTD input, 3 wires with low resistance and no difference should be used. 　　2) The input signal line should be far away from the power line of the instrument. Power supply and load lines to prevent noise disturbances. 　　3) The power cord of the instrument is generally disturbed by the power supply. 　　4) Instrument complement ...
	Introduction and wiring method of Japan physical and chemical RKC thermostat 　　The core control algorithm of the temperature regulator is PID control, P (Proportional) ratio + I (Integral) point + D (Differential) differential control. In addition to the traditional PID control algorithm, RKC also has ON-OFF control, custom parameter control, adaptive parameter control and other algorithms, ...
	RKC Thermostats – How to Choose a Thermocouple? The selection of thermocouples should be based on comprehensive considerations such as the operating temperature range, the required accuracy, the operating atmosphere, the performance of the measured object, the response time and the economic benefits. 1. Selection of measurement accuracy and temperature measurement range 1) The operating temperature is 1300-1800°C, and the accuracy is required to be more accurate than ...
	Where you need to pay attention to the wiring of the RRKC thermostat 1. For thermocouple input, the corresponding compensation wire should be used. 2. RTD input, 3 wires with low resistance and no difference should be used. 3. The input signal line should be far away from the power line of the instrument. Power supply and load lines to avoid noise interference. 4. Instrument power cord ...
	Introduction to the types of alarms for RKC thermostats * Alarm table {ALM1} (standard built-in) A: Upper limit deviation alarm G: Standby upper and lower limit deviation alarm attached B: Lower limit deviation alarm H: Upper limit input value alarm C: Upper and lower limit deviation alarm J: Lower limit input value alarm D: Alarm in the range K: Attached standby ...
	What are the technical parameters of the rkc thermostat - the jump thermostat? 1. Electrical parameters: (1) VDE, CQC, UL, TüVAC250V 50-60Hz 10A (resistive load) (2) ULAC125V 50Hz 15A (resistive load) 2. Operating temperature range: -50-270°C (optional), temperature accuracy: ≥ ±2°C 3. Reset and action ...
	Common faults and analysis of thermostats Common faults of thermostats 1. There is no display when the power is on. This type of problem first determines whether the power supply is available and whether the power supply matches the power supply required by the thermostat, and then checks whether the wiring is secure. The problem is still there, then it is the problem of the thermostat itself. 2. There is a display, and the control is wrong. This...
	RKC Level Gauge - the principle of the selection of float level gauges The float level gauge is widely used, mainly used in petroleum processing, food processing, chemical industry, water treatment, manufacturing, electric power, papermaking, metallurgy, ships and boilers and other industrial automation processes to measure and control the level. 1. Pay attention to the specific working conditions. As introduced ...
	RHK thermostat – a rapid detection method for common air conditioner thermostats 1 Bellows or diaphragm air conditioner thermostat Fault Symptom: Poor contact or burning, resulting in the circuit cannot be connected; The frequent action of the contact arc and sticking causes the circuit to be unbreakable; Leakage of thermostat in the temperature sensing chamber, causing the contacts to fail to operate and lose control ...
	RKC thermostat Digital display controller parameter setting method A digital display controller is a simple controller with indication, control, remote transmission and alarm functions. As a secondary instrument commonly used in sensors, it is very important to operate and use it correctly. Applications such as level control, temperature control, pressure control and parameter value display of measured variables. ...
	RKG thermostat – how the temperature controller sets the parameters 1. Lower limit deviation alarm setting: press the SET key to select and display "SLP", the green display screen displays the value of the parameter, and select the shift, increment, and decrement keys to set or modify the parameter. This parameter indicates the difference between the alarm point and the master setpoint. 2. The upper limit deviation alarm is set ...
	The main technical specifications of the RKG thermostat Input: all kinds of thermocouple (TC), RTD standard current and voltage signals (see input type table); Basic error: 0.5% of the input full-scale ±±1 word; Resolution: 1°C, 0.1°C; Sampling period: 3 times/sec Alarm function: ...
	RKG thermostat - an introduction to the relevant knowledge of temperature controllers The temperature controller is an electrical switchgear that controls the temperature of an air-conditioned room. The temperature range in the air-conditioned room controlled by the temperature controller is generally 18°C--28°C. The temperature controller commonly used in window air conditioners uses the principle of pressure to push the contacts on and off. Its structure consists of bellows ...
	Specifications and models of RKC thermostats CH102 (48×48×100mm) CH402 (48×96×100mm) CH902 (96×96×100mm) 1. RH400 size: 48*96, depth 60, about 250g 1. Thermocouples: K, J, R, S, B, E, N, T, W5RE/W6RE, PL‖, U, L ...
	What are the rich functions of RRKC thermostats – wall mounted thermostats? The wall-mounted thermostat is an ultra-thin intelligent thermostat that integrates measurement, display, control, alarm, recording and other functions, which can realize accurate measurement and control of temperature, pressure, flow and other parameters. Available in three sizes of 5 inches, 7 inches and 9 inches, a total of 12 models are available ...
	RRC thermostat - how to adjust the smart thermostat 1. Set temperature: Press the SET button to set or view the temperature set point. Press the SET button digital tube characters to start flashing, indicating that the instrument has entered the setting state, press the △ key to increase the set value, press the ▽ key to decrease the set value, long press the △ key or ▽ key The data will change rapidly, press the SET key again ...
	Key features of the RLC thermostat: Thermocouples, RTDs, analog and other signals are freely inputted, and the range can be set freely; The software zeros the full degree, the cold end measures the temperature separately, the amplifier is self-stabilizing, and the display accuracy is better than 0.5%FS; Fuzzy theory combined with traditional PD method, fast and stable control, advanced tuning ...
	RKC Thermostat Common faults of thermostats 　　The power indicator is normal, but the temperature control meter has no on-screen display. This kind of fault is mostly caused by the heating of the voltage regulator element (7805 or 7812) of the temperature controller during long-term use, resulting in a break point in the solder joint, and sometimes a virtual soldering occurs at the factory, resulting in re-soldering. ...
	What are the characteristics of RLC thermostats – mechanical thermostats? 1. Used to control fan coil unit, electric valve, damper and other equipment; 2. The switch adopts toggle type, which feels comfortable and has a long life; 3. Set the temperature by twisting (the temperature range can be limited); 4. The thermostat can be installed directly on the wall or on the standard junction box; ...