Classification and introduction of Banner sensors

1. It is necessary to prevent the sensor from engaging with corrosive gases, preventing it from corroding and affecting the effectiveness of measurement. 2. Assuming that the measurement is a high-temperature medium, it is necessary to see whether the temperature is within the appropriate temperature scale of the sensor.

1. Discrete photodiode with color filter The traditional practice of sensing color is to combine three to four photodiodes on a single chip, with red, green, and blue color filters placed on the surface of the photodiode (usually two blue color filters are combined together to compensate for the ...

Pressure sensors are mainly used in: booster cylinders, boosters, gas-liquid booster cylinders, gas-liquid boosters, presses, compressors, air conditioning and refrigeration equipment and other fields. 1. It is applied to hydraulic system The pressure sensor is mainly used to complete the closed-loop control of the force in the hydraulic system. When the control ...

1. Fully automatic calibration When the workpiece enters the sensitive area of the probe, hold down the "SET" button for 3 seconds, and the sensitivity value will be set and displayed in green 2. Two-point calibration When the workpiece is not in the sensitive area, hold down the "SET" key for three seconds, there is a ...

PEOPLE CAN HEAR THE SOUND DUE TO THE OSCILLATION OF THE OBJECT, ITS FREQUENCY IS IN THE RANGE OF 20HZ-20KHZ, BEYOND 20KHZ IS CALLED ULTRASOUND, BELOW 20HZ IS CALLED INFRASOUND. THE COMMONLY USED ULTRASONIC FREQUENCY IS TENS OF KHZ-TENS OF MHZ. Ultrasonic is a type of mechanical vibration in an elastic medium ...

High sensitivity Lightweight and flexible, easy to install and buried Electrical insulation and chemical stability. Optical fiber itself is a highly insulating and chemically stable substance, which is suitable for harsh environments such as high-voltage isolation and flammable and explosive in power systems and chemical systems Good security ...

1. The use of ultrasonic spacer sensor skills An ultrasonic sensor consists of three parts: an ultrasonic transducer, a processing unit, and an output stage. First, the processing unit excites the ultrasonic transducer with voltage, and after it is excited, it announces the ultrasonic wave in the form of pulses, and then the ultrasonic transducer is transferred to withstand ...

The first is that the pressure rises and the transmitter cannot convey. In this case, the first thing to do is to check the pressure connection for air leaks or blockages. If not, check the wiring method and power supply. If the power supply is normal, simply pressurize and see if the output changes, or if the sensor part outputs. As...

1. Non-contact detection, the sensor has a long service life and no damage to the inspected object. 2. It is used for long-distance detection and has a wide range of uses. 3. There are many types of objects to be inspected, including objects that have an impact on light propagation. 4. High response frequency, suitable for high-speed assembly line ...

A proximity sensor is a device with the ability to perceive the proximity of an object, which uses the sensitivity of the displacement sensor to the approaching object to identify the proximity of the object and output the corresponding switching signal. For this reason, proximity sensors are often referred to as proximity switches. It is an alternative to contact detection ...

1. Realize the simultaneous measurement of multiple physical parameters (temperature and strain) or chemical parameters on a single optical fiber; 2. Improve the measurement range of the measurement system and reduce the measurement time; 3. Improve the detection ability of the signal receiving and processing system, improve the spatial resolution and measurement of the system.

· punch · vibrating feeder · Transporter · Pill counting · Small object detection · oven · Semiconductor processing equipment · Robotic arms and mobile machinery ...

Pressure is one of the important parameters in industrial production, and in order to ensure the normal operation of production, it must be monitored and controlled. The following are common terms used when selecting pressure sensors: Standard press The magnitude of the pressure expressed by atmospheric pressure is greater than the atmospheric pressure ...

(1) The sensing element in the distributed optical fiber sensing system is only optical fiber; (2) The one-dimensional distribution map to be measured in the whole optical fiber area can be obtained in one measurement, and the two-dimensional and three-dimensional distribution of the measured can be determined by erecting the optical fiber into a grating shape; (3) The empty ...

(1) The sensing element in the distributed optical fiber sensing system is only optical fiber; (2) The one-dimensional distribution map of the measured optical fiber area can be obtained in one measurement, and the two-dimensional and three-dimensional distribution of the measured can be measured by erecting the optical fiber into a grating-like shape; (3) The space of the OTDR system ...

1. It is directly used for the determination of various pressures: air pressure, water pressure, hydraulic pressure (including water pressure), various blood pressure measurements of people in life, etc.; 2. Pressure sensors are used in automobiles, some high-end motorcycles and almost all internal combustion engines; 3. Level gauge: all kinds of liquid level ...

Infrared sensor is a kind of sensor that uses infrared rays to process data, which has the advantages of high sensitivity, and the infrared sensor can control the operation of the driving device. Infrared sensors are commonly used for non-contact temperature measurement, gas composition analysis and non-destructive testing.

1. Photoelectric head dust masking When the photoelectric sensor is operating, it is easy to accumulate dust or oil dirt on the receiving head, resulting in problems such as insensitive sensor response, false triggering or non-triggering, and even failure to operate normally. At this time, we need to clean the photoelectric head. Cleaning method: ...

(1) Fork photoelectric sensor Placing an optical transmitter and a receiver facing each other on either side of a slot is a fork photoelectric. The luminaire emits infrared or visible light, and the light receiver receives the light in an unobstructed condition. But when the detected object passes through the slot, the light is blocked ...

1) Large adjustable range, up to 10,000ppm, a wide range of sensors can be used; 2) Programming through simple circuits and easy-to-use software; 3) Pressure sensors are manufactured in a unique way and are specifically designed to meet industrial needs; 4) Sensors ...