Fuji Electric inverter inverter fault code fault code fault after the corresponding treatment method is given.
OC alarm.
Keyboard board LCD display: add, subtract, constant speed overcurrent.
For OC alarms with large currents in a short period of time, under normal circumstances, there is a problem with the current detection circuit of the driver board, and the module may also be shocked (damaged), and the fault may continue to occur after reset. The reasons are basically as follows: the arc effect caused by the increase in load current caused by the long motor cable, the critical cable selection or the output cable joint is loose, and the load current rises due to cable damage.
When the 24V fan power supply of the inverter is short-circuited, the small capacity (below 7.5G11) will also cause OC3 alarm, at this time, the 24V fan power supply on the motherboard will be damaged, and other functions of the motherboard will be normal. If there is an alarm of 1 or OC2 and it cannot be reset, or the alarm of OC3 is displayed as soon as it is powered on, it may be that there is a problem with the motherboard; If the OC3 alarm is displayed when you press the RUN button, the driver board is broken.
OLU alarm.
Keyboard Pad LCD Display: Inverter Overloaded.
When this alarm occurs in the G/P9 series inverter, it can be solved by three methods: firstly, modify the parameter settings of torque lifting, acceleration and deceleration time and energy-saving operation; Secondly, use a card meter to measure whether the output of the inverter is really too large; Finally, use an oscilloscope to observe the output of the detection point in the upper left corner of the motherboard to determine whether the motherboard is damaged.
OU1 alarms.
Keyboard Pad LCD Display: Overvoltage during acceleration.
When the OU alarm occurs in the general inverter, the first thing to consider is whether the cable is too long, whether the insulation is aging, and whether the electrolytic capacitor in the intermediate link of DC is damaged. At the same time, in-line self-tuning of motors with large inertia loads can be considered. In addition, a multimeter is used to measure the voltage in the intermediate link of the DC at start-up. If the display voltage of the measuring instrument is different from the LCD display voltage of the operation panel, the detection circuit of the motherboard is faulty and the motherboard needs to be replaced. When the DC bus voltage is higher than 780VDC, the inverter will give an OU alarm; When it is lower than 350VDC, the inverter will give an undervoltage LU alarm.
LU alarm.
Keyboard pad LCD display: undervoltage.
If the device frequently under-voltage alarm, you can consider initializing the parameters of the inverter (confirmed after H03 is set to 1), and then increasing the carrier frequency of the inverter (parameter F26). If the E9 device LU undervoltage alarms and cannot be reset, there is a problem with the (power) driver board.
|
More on that
|
How is data protection carried out? - Fuji Electric inverter
Set F00 to 1 for data protection, which requires the STOP button + RISE button to operate.
|
|
9 nuclear energy innovation and excellence industry projects have been implemented in a centralized manner, and Fujifilm ultrasonic flowmeters with large-diameter applications have been selected
On October 15, the "China Shandong Nuclear Energy (Equipment) Industry Development Promotion Conference" hosted by the Weihai Municipal Government, Shandong Provincial Power Bureau and the State Power Investment Group was held in Rongcheng City, Weihai, Shandong.
|
|
There are always answers to common questions about the use of inverters and transmissions, there are always things you don't know
1. Why is the leakage circuit breaker easy to trip when using the inverter?
This is because the output waveform of the inverter contains higher harmonics, and the motor and the cable between the inverter and the motor will generate a leakage current, which is much larger than that when the motor is driven by the power frequency.
...
|
|
Fuji Electric's Power Semiconductor Symposium officially kicked off
On March 16, 19, Fuji Electric Power Semiconductor Symposium was held in Guangzhou. More than 90 customers and agents from all over the country were invited. Fuji Electric looks forward to carrying out in-depth communication with you according to the publicity and education content of this seminar, so that everyone can have a good understanding of Fuji Electric.
|
|
Development status of imported ultrasonic flowmeter
Fujifilm ultrasonic flowmeter is a non-contact flowmeter that has only been applied with the rapid development of integrated circuit technology in the past ten years, which is suitable for measuring fluids that are not easy to contact and observe, as well as large pipe diameter flows. Together with the water level gauge, it forms an open channel flow meter for flow measurement of open water ...
|
|
Current status and outlook of Fuji Electric's power generation plant business
Fuji Electric has set forth its management philosophy of "Contributing to a Rich Society, Challenging the Limits of Creativity, and Developing in Harmony with the Natural Environment," and one of the pillars of its management policy is to contribute to the sustainable development of society through energy and environmental businesses.
This article will focus on the energy sector ...
|
|
The solution to the problem of inverter interference – Fuji Electric
A common phenomenon of frequency converter interference
1. As soon as the inverter of the heat exchange station is opened, the pressure transmitter jumps randomly;
2. In the water supply controlled by the inverter, the pressure transformer is used as the signal to collect the pressure, and the pressure transformer is interfered by the inverter;
3. When the inverter starts the motor, the voltage transformer signal is unstable and beats badly;
4. ...
|
|
The semiconductor market is booming, and Fuji Electric's industrial pattern is rapidly improving
The Semiconductor Industry Association (SIA) recently announced that global semiconductor sales in June 2017 reached $32.6 billion, up 2.0% compared with the previous month; This is a 23.7% surge compared to the same period last year. Semiconductor sales in the second quarter of this year were US$97.9 billion, up 5.8% quarter-on-quarter and 23.7% year-on-year; This year...
|
|
Application of Fujifilm ultrasonic flowmeter in the semiconductor industry
Shanghai Jita Semiconductor, located in the Lingang New Area of the Shanghai Free Trade Zone, has a total investment of 35.9 billion yuan to build an 8-inch production line with a monthly production capacity of 60,000 pieces and a 50,000-piece 12-inch special process production line project and a production base of 300mm semiconductor silicon wafers of Shanghai Xinsheng Semiconductor. Lingang 2 iconic semiconductors ...
|
|
Fuji Electric ships ship exhaust gas cleaning system in the first shipment
2018-10-22
Fuji Electric Pillar Co., Ltd., headquartered in Tokyo, Japan, President Michihiro Kitazawa announced today that it is shipping its first ship exhaust gas cleaning system (EGCS) through its Chiba plant.
1. Background
In order to reduce the air pollutant sulfur oxides (SOx) ...
|
|
Typical Cases | Leakage problem and treatment of lined magnetic flap level gauge in liquid chlorine tank level monitoring
1. Application and development of magnetic flap level gauge in liquid chlorine tank level detection
Liquid chlorine is a high-risk and highly toxic substance, which is highly corrosive, and once it causes leakage, it will cause great harm to the environment and the human body, so it is particularly important to ensure the safe operation of the liquid chlorine tank. And accurate and reliable control ...
|
|
Fuji Electric's multi-axis amplifier won the "Innovative Product" award
Since its inception, the New Automation Summit Forum has been an exchange platform to promote industrial exchanges and promote the level of automation applications. Fuji Electric is honored to be invited to participate in the 14th MM · New Automation Forum 2018 with the theme of "Data as a Starting Point · Manufacturing Excellence". At the forum, the industry ...
|
|
Fujifilm Portable Ultrasonic Flow Meter - Water Supply Company Site Check Pump Room Flow Application
Fujifilm portable ultrasonic flowmeter is used to check the flow rate at the outlet of a water pump in the field
Error analysis in the flow measurement process
Check for abnormal readings from the in-line flow meter
Avoid process interruptions and the background of more expensive tube opening costs
Waterworks are mainly used to treat water, and generally have the following processes.
|
|
What are the self-protection functions of Fuji Electric - inverter?
After years of development, the inverter (VFD) has begun to transition from a purely industrial product to a civilian field. The use of VFD can be said to have gone to the countryside, (constant pressure water supply) penetrated into thousands of households (inverter air conditioning). But after using it for a while, you will find that the failure rate of VFD is much higher than that of the average household ...
|
|
Fuji Electric will expand its production of power semiconductors by an additional 40 billion yen, and may increase the production of power semiconductors by another 50 billion yen in the future
Japan's Fuji Electric plans to invest an additional 40 billion yen (USD 365 million) to expand production of power semiconductors. It is reported that the power semiconductors produced by the company are mainly used in the power system of air conditioners, electric vehicles and other products.
According to Nikkei Asian Review, Fuji Electric ...
|
|
Fuji inverter - what is the role of frequency conversion speed regulation technology in the field of energy conservation and environmental protection?
The frequency conversion speed regulation function of the inverter (hereinafter referred to as -VFD) is to convert the three-phase power frequency (50Hz) AC power supply (or any power supply) into a three-phase AC power supply with adjustable voltage and frequency. Frequency conversion speed control device can also be sometimes called VVVF, which is mainly used to adjust AC motors (asynchronous or synchronous machines).
|
|
Turbine flow meter
DN20 Turbine Flowmeter Description—It has the characteristics of simple structure, high measurement accuracy, long service life, simple operation and easy maintenance. It is widely used in metallurgy, chemical industry, petroleum, urban construction, environmental protection, food and other fields.
1. Technical parameters:
Executive standard: Turbine flow sensor (JB...
|
|
Analysis of common causes and preventive measures of inverter failures - Fuji Electric
1. Analysis of common faults in the main circuit
The main circuit is mainly composed of three-phase or single-phase rectifier bridges, smoothing capacitors, filter capacitors, IPM inverter bridges, current limiting resistors, contactors and other components. Many of these common faults* are caused by electrolytic capacitors. The life of an electrolytic capacitor is mainly determined by the ...
|
|
The Water Resources Bureau uses Fuji imported portable ultrasonic flowmeter for measurement
At present, the measurement of production water of enterprises is mostly the on-site installation of electromagnetic flowmeters or fixed ultrasonic flowmeters by local water conservancy bureaus as the measurement eyes, and they always keep an eye on the water used by enterprises to protect the use of public resources and eliminate waste.
In stationary electromagnetic flowmeters or stationary ultrasonic flowmeters ...
|
|
Fuji Electric has launched a high-speed control system for factories to increase production capacity
Fuji Electric Corporation (headquartered in Tokyo, Japan; President: Michihiro Kitazawa announced the launch of a high-speed control system for factories using the company's newly developed controller.
1. Summary
Due to the increasing variety of products and production volumes, manufacturing plants need to ...
|
|