Fujifilm ultrasonic flowmeter is a non-contact flowmeter that has only been applied with the rapid development of integrated circuit technology in the past ten years, which is suitable for measuring fluids that are not easy to contact and observe, as well as large pipe diameter flows. Together with the water level gauge, it forms an open channel flow meter for flow measurement of open water flow. The use of ultrasonic flowmeter does not need to install a measuring element in the fluid, so it will not change the flow state of the fluid, no additional resistance, and the installation and maintenance of the flowmeter can not affect the operation of the production pipeline, so it is an ideal energy-saving flowmeter.
As we all know, the current industrial flow measurement generally has the problem of large pipe diameter and large flow measurement difficulty, this is because the general flowmeter with the increase of the measurement pipe diameter will bring difficulties in manufacturing and transportation, the cost increases, the energy loss increases, and the installation not only these shortcomings, but also the ultrasonic flowmeter can be avoided. Because all kinds of ultrasonic flowmeters can be installed outside the pipe and non-contact current measurement, the cost of the flowmeter is basically irrelevant to the diameter of the pipeline to be measured, and the cost of other types of flowmeters increases greatly with the increase of caliber, so the larger the aperture, the more superior the function price ratio of other types of flowmeters with the same function. Considered to be a good large-diameter flow measurement instrument, the Doppler ultrasonic flowmeter can measure the flow rate of duplex medium, so it can be used for the measurement of dirty flow such as sewer and sewage discharge. In power plants, it is much more convenient to use a portable ultrasonic flowmeter to measure the flow rate of large pipe diameters, such as the water inlet of the water turbine and the circulating water of the steam turbine, than the flow rate of the pito-tube in the past. Ultrasonic flow juice can also be used for gas measurement. The pipe diameter can be applied from 2 cm to 5 m, from open channels and culverts several meters wide to rivers 500 m wide.
In addition, the measurement accuracy of Fujifilm ultrasonic flowmeter is almost not affected by the temperature, pressure, viscosity, density and other parameters of the measured fluid, and can be made into non-contact and portable measuring instruments, so it can solve the flow measurement problems of highly corrosive, non-conductive, radioactive and flammable and explosive media that are difficult to measure by other types of instruments. In addition, in view of the non-contact measurement characteristics, coupled with reasonable electronic circuits, one flowmeter can be adapted to a variety of pipe diameter measurement and a variety of flow range measurement. The adaptability of ultrasonic flowmeters has advantages that are incomparable with other instruments. Ultrasonic flowmeter has some of the above advantages, so it has received more and more attention and developed to product serialization and generalization, and has been made into standard, high-temperature, explosion-proof and wet instruments with different channels to adapt to flow measurement of different media, different occasions and different pipeline conditions.
|
More on that
|
Did you really choose the right circuit breaker?
How to choose a circuit breaker?
In fact, there are not a few people who do not know the steps of circuit breaker selection, Fuji Electric's suggestion is that you can roughly choose the model of circuit breaker by following the following 7 steps.
When the load is a motor, why must it be protected with a circuit breaker + solenoid switch?
That...
|
|
The 7th generation X-series IGBT module product line has been expanded
Fuji Electric Corporation (headquartered in Tokyo, Japan, President Mitsuhiro Kitazawa) is pleased to announce that the company has expanded its 7th generation X-Series IGBT module product line*¹ to target the massive wind power market and has begun sample shipments in the 1,700 volt voltage class.
*1: Insulated Gate Dual ...
|
|
The solution to the problem of inverter interference – Fuji Electric
A common phenomenon of frequency converter interference
1. As soon as the inverter of the heat exchange station is opened, the pressure transmitter jumps randomly;
2. In the water supply controlled by the inverter, the pressure transformer is used as the signal to collect the pressure, and the pressure transformer is interfered by the inverter;
3. When the inverter starts the motor, the voltage transformer signal is unstable and beats badly;
4. ...
|
|
Fuji inverter - what is the role of frequency conversion speed regulation technology in the field of energy conservation and environmental protection?
The frequency conversion speed regulation function of the inverter (hereinafter referred to as -VFD) is to convert the three-phase power frequency (50Hz) AC power supply (or any power supply) into a three-phase AC power supply with adjustable voltage and frequency. Frequency conversion speed control device can also be sometimes called VVVF, which is mainly used to adjust AC motors (asynchronous or synchronous machines).
|
|
Accumulation of experience in testing skills in inverter maintenance
1. Detection of fixed resistors.
A. Connect the two pen pens (regardless of positive and negative) with the pins at both ends of the resistor to measure the actual resistance value. In order to improve the measurement accuracy, the range should be selected according to the magnitude of the nominal value of the resistance to be measured. Due to the nonlinear relationship of the ohmic scale, its ...
|
|
Application case of automatic welding of pipe flange in flange connection ultrasonic flowmeter industry
Manual pipe-flange welding needs professional welders to weld, not only high cost, but also has problems such as low welding efficiency, unstable welding quality and high labor intensity, Jinan Jinluding Welding Technology Co., Ltd. developed H1440T series pipe-flange automatic welding can effectively solve the flange connection ...
|
|
Inverter control motor leakage causes and measures
The cause of the leakage problem
We all know that the three-phase stator winding of the motor flows through the current to produce a rotating magnetic field, according to the principle of magnetoelectric induction, the shell of the motor will produce an induced electromotive force, the size of this electromotive force depends on the size of the switching frequency of the inverter IGBT, due to the high ...
|
|
How to set the motor characteristic parameters of the inverter - Fuji Motor
Do you know how to set the motor characteristics of the inverter-controlled mechanical equipment? Next, Sanke Inverter will introduce this aspect for you through the following content.
1. Parameters to be set for the motor
When the inverter (hereinafter referred to as the -VFD) is in the "vector control" (F0-03=1) mode ...
|
|
Fuji Electric has launched a high-speed control system for factories to increase production capacity
Fuji Electric Corporation (headquartered in Tokyo, Japan; President: Michihiro Kitazawa announced the launch of a high-speed control system for factories using the company's newly developed controller.
1. Summary
Due to the increasing variety of products and production volumes, manufacturing plants need to ...
|
|
Introduction to the application case of Fujifilm ultrasonic flowmeter in power plant flow measurement
Due to the outstanding technical application advantages of Fujifilm ultrasonic flowmeter, Fujifilm ultrasonic flowmeter has been widely concerned in various fields such as power plant flow measurement, which can be reflected from the following application cases.
Circulating water flow is measured in hydropower plants ...
|
|
Fuji Electric's multi-axis amplifier won the "Innovative Product" award
Since its inception, the New Automation Summit Forum has been an exchange platform to promote industrial exchanges and promote the level of automation applications. Fuji Electric is honored to be invited to participate in the 14th MM · New Automation Forum 2018 with the theme of "Data as a Starting Point · Manufacturing Excellence". At the forum, the industry ...
|
|
Fuji Electric Systems Co., Ltd. will release the EX100 series mini uninterruptible power supply system
Fuji Electric Systems Co., Ltd. will release the Fuji Mini UPS EX100 Series on October 5, 2010. This is a new series of high-efficiency uninterruptible power supply systems (UPS) with capacities ranging from 1kVA to 3kVA.
Fuji Electric ...
|
|
Application of Fujifilm ultrasonic flowmeter in the semiconductor industry
Shanghai Jita Semiconductor, located in the Lingang New Area of the Shanghai Free Trade Zone, has a total investment of 35.9 billion yuan to build an 8-inch production line with a monthly production capacity of 60,000 pieces and a 50,000-piece 12-inch special process production line project and a production base of 300mm semiconductor silicon wafers of Shanghai Xinsheng Semiconductor. Lingang 2 iconic semiconductors ...
|
|
Fujifilm Portable Ultrasonic Flow Meter - Water Supply Company Site Check Pump Room Flow Application
Fujifilm portable ultrasonic flowmeter is used to check the flow rate at the outlet of a water pump in the field
Error analysis in the flow measurement process
Check for abnormal readings from the in-line flow meter
Avoid process interruptions and the background of more expensive tube opening costs
Waterworks are mainly used to treat water, and generally have the following processes.
|
|
Fuji Electric – How do you determine the breaking capacity of a circuit breaker?
(1) Is there a difference between ICU and ICS in the sample?
(2) What is breaking capacity? How do I choose a breaking capacity?
(3) Why must the circuit breaker use 0.8-0.9 times the rated current value?
(4) How to determine the sensitivity current value?
(5) The insulation space of the circuit breaker must exist ...
|
|
Adopt the "ancient tree" Fuji Electric of East China Normal University to practice the concept of "green development".
With the conclusion of the 19th National Congress of the Communist Party of China, the spirit of the major conferences has been newly conveyed. Among them, General Secretary Xi Jinping said that in order to practice the concept of green development, we must establish and practice the concept that lucid waters and lush mountains are invaluable assets, and to protect the ecological environment is to protect productivity, and to improve the ecological environment is to develop the ecological environment.
|
|
23 projects signed at the China-Japan Energy Conservation and Environmental Protection Forum, Fuji Electric contributes "green energy"
From December 23 to 24, 2017, the 11th China-Japan Energy Conservation and Environmental Protection Comprehensive Forum, jointly organized by the National Development and Reform Commission and the Ministry of Commerce, the Ministry of Economy, Trade and Industry of Japan and the Japan-China Economic Association, was held in Tokyo. More than 800 government officials, experts, scholars, and entrepreneurs from China and Japan attended the event.
|
|
Application of frequency converter technology in injection molding machines
Injection molding is one of the main molding methods to make thermoplastics into various products, compared with other plastic molding methods, injection molding method has the advantages of molding products with complex structure and size, strong adaptability to plastics, short molding cycle, high production efficiency and easy to realize automation.
|
|
Can ultrasonic flowmeters be used in the production and processing of edible oil?
Can a small flow ultrasonic flow meter be used for flow measurement of soybean oil?
There are several steps in the processing of edible oil that require the use of flow meters to measure the volume and weight of how much oil flows out of the pipeline. Enterprises that produce and process edible oil need to be aware of the crude oil and ...
|
|
Fuji Electric - How to choose a high-power inverter model
In order to achieve a more efficient and controllable operation of the motor, and avoid the waste of power of the motor drive system, the inverter came into being. However, due to the variety of motor load types, the functional requirements for the equipped inverter are also different, so how to choose the right transformer for the motor...
|
|
Contact
working hours
