Product Description: Thru-beam sensor, 30 m detection range, red light, switch-on on bright, AC/DC type, relay output, fixed cable, cost-optimized series for standard tasks, small housing for large structures, high visibility LED, universal voltage version, relay output.
Product Description | | Through-beam photoelectric sensor, 30 m detection range, red light, dark on, DC type, 2 push-pull outputs, transmitter off, M12 plug |
System components | | Transmitters | LD31/73c/76a | | receiver | LV31/73c/136 | General specifications | | Effective detection distance | 0 ... 30 m | | Detection range limit values | 43 m | | light source | LED | | The type of light source | Modulated visible red light, 630 nm | | Alignment aids | Yellow LED:
1. LED on: Enough light signal is received, and the transmitter and receiver are properly aligned
2. LED flashing: Reach the switch point
3. LED off: The beam is interrupted or misaligned | | Spot diameter | Approximately 800 mm are 30 m apart | | Divergence angle | Transmitter: 1,5 ° , Receiver: 1,5 ° | | Ambient light limitations | 50000 Lux ; According to EN 60947-5-2 | Functional safety-related parameters | | MTTFd | 750 a | | Mission Time (TM) | 20 a | | Diagnostic Coverage (DC) | 90 % | Indicator/method of operation | | Work indicator | Green LED: Powered on | | Function indicator | Yellow LED:
1. LED is always on: signal > 2 x switching points (function reserved)
2. LED flashing: The signal is between 1 x switch and 2 x switch points
3. LED off: signal < switch point | Electrical Specifications | | Operating voltage | 10 ... 30 V DC | | Ripple | 10 % | | No-load current | Transmitter: ≤ 18 mA
Receiver: ≤ 18 mA | input | | Test inputs | Under +UB the emitter is deactivated | output | | Switch type | Turn on when dark | | Signal output | 2 push-pull (4-in-1) outputs, short-circuit protection, reverse polarity protection | | Switching voltage | 30 V DC max | | Switching current | 100 mA max | | Voltage drop | ≤ 1,5 V | | Switching frequency | ≤ 250 Hz | | Response time | ≤ 2 ms | compliance | | Product standards | EN 60947-5-2 | Certifications and certificates | | EAC Conformity | TR CU 020/2011 | | Ingress protection | II, When the pollution class is 1-2 (according to IEC 60664-1), the rated voltage is ≤ 250 V AC The output circuit of the input circuit is basically insulated according to EN 50178 and the rated insulation voltage is 240 V AC | | UL recognized | cULus recognized, Class 2 power supply, Class 1 enclosure | | CCC certified | At a rated voltage of ≤ 36 V, the product does not require CCC certification/marking | Environmental conditions | | Ambient temperature | -30 ... 55 °C (-22 ... 131 °F) | | Storage temperature | -40 ... 70 °C (-40 ... 158 °F) | Mechanical Specifications: | | Enclosure width | 18 mm | | Enclosure height | 62 mm | | Enclosure depth | 35 mm | | Ingress protection | IP67 | | connect | 4-pin M12 x 1 connector | | material | | | enclosure | polycarbonate | | Optical end faces | PUMA | | quality | Transmitter: 24 g
Receiver: 24 g |
Our customer-centric service concept: the pursuit of a full range of services is a high-quality, high-standard service, the pursuit of every detail of the service process. It is impossible for interests to blossom into brilliant flowers from lies. Only when every process, every action and every detail of the service is professional and careful, can we meet or even exceed the expectations of customers, so that customers can be satisfied and recognize us. Honest, professional, affordable, and fast, so you can rest assured. "Honest and professional service, affordable price, continuous improvement" is our service philosophy.
This article introduces P+F/Bulb Photoelectric Sensor LA31/LK31/25/31/115 products, if you are interested in P+F/P+F/Bulb Photoelectric Sensor, please also contact our staff, we are looking forward to your call, hope our technology and service can bring you a better experience.
|
More on that
|
P+F/Pixel Sensor GL30-RT / 32 / 40A / 98A Light/Dark
Product Introduction: Photocell Sensor, Zinc Die-Cast Housing, 30mm Slot Width, Red Light, Light/Dark, Sensitivity Regulator, DC Version, PNP Output, 3-Pin M8 Plug, Optimized for Detecting Small Parts, High Switching Frequency, Multi-Device Installation Possible, No Mutual Interference (No Crosstalk), Sensitivity ...
|
|
P+F/Bejiafu capacitive sensor CJ15+U1+A2 wire cross-sectional area of 2.5mm2
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Optical Data Coupler DAD15-8P-R-2388 interface BASE-TX
Product Introduction: The optical communication system supports two-way communication between storage and retrieval systems, transmission vehicles, automatic guided vehicles and monorail conveyors. This is an alternative to complex and problematic cables, slip rings and other transmission solutions. The transmission between the two sites is replaced by infrared light, which is made up of several ...
|
|
P+F/Capacitive sensor CBN5-F46-E2-10M 5mm
Introduction:P+F Capacitive Sensor CBN5-F46-E2-10M Flat Housing; reverse polarity protection; Fixing slot for cable tie, through-hole for screw mounting, cULus listed, general use.
Product parameters
...
|
|
P+F/Print Marker Luminescence Scanner DK50-UV-190 / 115B / 147
Product Introduction: Color is usually the distinctive feature of a product, so color recognition and reliable detection play an increasingly important role in industrial automation. The color sensors of P+F are very good and cover most applications, e.g. for fixed detection distances.
|
|
P+F Capacitive Sensor CJ40-FP-A2-P4 4-wire
Introduction:P+F capacitive sensor CJ40-FP-A2-P4 series rectangular, housing material is POM / metal, output type 4 wires, non-flush mounting, DC voltage type, screw terminal connection type, protection class IP65.
...
|
|
P+F/Inductive sensor NBB20-L2-E2-V1 20mm
Introduction: Smooth or threaded stainless steel housing for inductive sensors; reverse polarity protection and short circuit protection; LED status indication; M8, M12 connector connection or terminal wiring; PVC, PUR or silicone cable outlet; 2-wire, 3-wire, 4-wire DC, AC, NAMUR and AS ...
|
|
P+F/Sensor NBN4-12GM40-E2-V1 4 mm
Introduction: The inductive sensor is to use electromagnetic induction to convert the measured physical quantities such as displacement, pressure, flow, vibration, etc. into the change of self-inductance coefficient and mutual inductance coefficient of the coil, and then convert the output of voltage or current change by the circuit to realize the conversion of non-electricity to electricity.
...
|
|
P+F/Beijiafu NBB2-6,5M25-E2-V3 inductive sensor
Product introduction: P+F Inductive sensor NBB2-6,5M25-E2-V3 2 mm flush Longer working distance Extended temperature range -40 ... +85 °C
Specifications:
Switch function
Normally open (NO)
Output type
PNP
Rated working distance
2 mm
Installation...
|
|
P+F/Double Sheet Sensor UDC-18GM-400-3E1-Y194142
Product Introduction: Ultrasonic double sheet detector is used to automatically and at high speed to distinguish substrate materials, labels, sheet-fed and double-fed, so as to protect the machine from waste in the production process. The whole system consists of an ultrasonic transmitter, an ultrasonic receiver and an external or built-in ...
|
|
P+F/Reflective Plate Photoelectric Switch ML100-55/95/103 360 degree view
Product Description: Retroreflective sensor with polarization filter, plastic housing, 5 m detection range, red light, adjustable sensitivity, on/off when light/dark, DC type, PNP output, M8 plug, compact design, easy to use, extremely bright and clear light spot, all-metal threaded mounting, ...
|
|
P+F Signal Conditioner S1SD-1AI-1C.H Resistance 50Ω
Introduction: The P+F signal conditioner SC series provides isolation in an extremely compact package and is optimized for the application requirements of the safe area. Connected via screw terminals, according to EN 60715:2001, mounted on a 35 mm DIN mounting rail.
...
|
|
P+F inductive sensor NBB0,6-3M22-E2 pulse
Description: P+F Inductive sensor NBB0,6-3M22-E2 pulse, nominal working distance: 0,6 mm, operating voltage: 10 ... 30 V, switching frequency: 0 ... 1400 Hz
peculiarity
0.6 mm, flush
Miniature design
Product parameters
...
|
|
P+F/Optical Fiber Optic Sensors SU18/16/35/40a/110/115/126a
Product Introduction: Fiber Optic Sensors for Glass and Plastic Fibers, Basic Production Line for DIN Rail Mounting, High Power Version, Sleek Design, Selectable 3 Response Times, Mutual Interference Prevention (No Crosstalk)
Detailed parameters:
...
|
|
P+F/Inductive sensor NBB2-12GM50-E2-V1 2 mm
Summary: Inductive proximity sensors are the preferred product for most applications that require the precise and non-contact detection of metal objects in mechanical or automated equipment. As a pioneer and market leader in the field of sensors, we offer our customers innovative, high-quality electrical products.
|
|
P+F/Logic Control Device 14bit Resolution
Introduction: Logic control units are widely used in the automation industry. In practice, they are capable of detecting digital or analog signals, displaying them and monitoring them. In order to solve the conversion and application between signals, we provide digital display meters, counters ...
|
|
P+F/Capacitive sensor CBB8-18GK75-E2-V1 with a diameter of 18 mm
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Capacitive sensor CBN5-F46-E0-Y286690 distance 5mm
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Double Blessing Timer KC-LCDC-48-2R-230VAC 142g
Introduction: P+F Timer KC-LCDC-48-2R-230VAC easy-to-read, backlit 2-line LCD display with icons for pre-selection and the status of both outputs; Add/subtract via 2 independent inputs, degree of protection IP65 (front).
...
|
|
P+F Multiturn Absolute Encoder AVM58-H
Introduction: In this construction, the gear structure is added on the basis of the singleturn code disc, through these interconnected gears, we can measure up to 16,384 turns (14 bits), so that the total accuracy of the encoder is 16 bits (single turn) plus 14 bits (number of turns), or the total precision ...
|
|
Contact
working hours
