Venal Information SHOW

	Performance characteristics of low-voltage busbar system - Wienal Introduction to the performance of low-voltage bus system: 1. The bus bar is not perforated, and is connected with the cable and copper bar through the connection clip or terminal 2. Switches, contactors and other electrical components can be directly hung on the bus through adapters 3. Save ...
	Features of Wiener busway The Wiener busway mainly acts on the aluminum conductor, which has a large current capacity and good electrical and mechanical properties. In addition, it uses a metal trough as the shell, so it is non-flammable, safe and reliable, and has a long service life. Compared with traditional power distribution, the equipment occupies a significantly smaller area and has a beautiful appearance. ...
	The essence of Wiener busbar technology 1. Closed busbar hooking technology Circuit breakers and contactors can be hooked on the bus through the bus adapter, and fuse switches and other products are directly attached to the bus, so the bus bar plays a two-layer effect of conductive and fixed rotation.
	220V DC Hazard of Bus System – Wiener The grounding of the DC system should include two situations: the one-point grounding of the DC system and the two-point grounding of the DC system. In the DC system, the positive and negative poles of the DC are insulated from the ground, and when the ground of one pole is generated, there is no grounding current due to the fact that there is no grounding current.
	Scope of application of busbar - Wiener busbar system Busbars are divided into hard busbars and soft busbars. According to its different shapes, hard buses can be divided into: rectangular busbars, tubular busbars, trough busbars, diamond busbars and so on. Rectangular busbars are the most commonly used busbars and are also busbars. ...
	The role of the busbar in the excitation system – Wiener The bus PT is used to measure the bus voltage on the high-voltage side of the main transformer, and is used to assist in grid connection. Before starting the synchronous grid connection, the excitation system actively adjusts the terminal voltage according to the bus voltage measured by the bus PT, so that the voltage on both sides of the grid-connected switch is basically equal, which is convenient for the same period of grid connection. ...
	Characteristics of single bus wiring in the switchgear - Wiener In power distribution equipment such as voltage distribution cabinets and switchgear at all levels of power plants and substations, the conductors connected between large electrical equipment such as generators and transformers and various electrical equipment are called busbars. Busbars, also known as busbars, are used to gather, distribute, and transmit electrical energy. The connection methods of the bus bar are ...
	Wiener Electric's busbar system escorts the operation of textile machinery equipment According to Wiener electrical engineer, the bus system is a process-assisted component, the main effect is to hook the switch on the adapter, and the adapter is then hooked on the copper bar, so that the full protection of the copper bar can be completed, and the safety factor is improved; The upper port of the switch can be connected without ...
	Phase of the busway in the low-voltage incoming line – Wiener According to the requirements of the relevant specifications, the placement of the three-phase busbar can be roughly divided into two kinds according to the model of the low-voltage distribution cabinet and the different manufacturers: horizontal placement and placement of the down wire, according to the order of placement.
	Wiener Data Center Bus System Although the service life cost of the busbar system is usually lower than that of the traditional wiring method, the busbar system still bears a considerable cost compared to other structural elements of the water supply and drainage or HVAC system. In addition, customized busbars ...
	The importance of busbar systems in low-voltage switchgear One of the characteristics of low-voltage switchgear is the multi-functional busbar system. The bus bar is a conductor that connects large electrical equipment such as generators and transformers with various electrical equipment. The role of the bus is to, sub-...
	Some of the Wiener series models 　　05802 Insulator with female thread, bolt, M8, height 35mm 08824 Platen connector for PE- and N-busbar 01 932 　　08825 Snap-on fastener, for PE- and N-busbars 01126-01129 and 019 ...
	Wiener busbar system PT disconnection treatment The judgment of PT three-phase voltage loss (symmetrical disconnection) is fundamentally the same for each manufacturer, and it is judged according to the three-phase no voltage and the current of the line. The same is true for PT asymmetrical wire breakage. After analyzing the characteristics of PT wire breaking, the specific judgment of PT asymmetric wire breaking of different manufacturers ...
	Busbar system in detail – Vernal 1. In the 60mm bus system, the square fuse type blocking switch can be directly hooked. 2. The 60mm bus system refers to the three-wire or four-wire bus spacing of 60mm. 3. Strip NH-fuse type load barrier switch with scale 00 ...
	What is the Wiener bus system The Wiener bus system is a standardized system for bus spacing, which is used in low-voltage power supply and distribution switchgear, so that the bus can both conduct electricity and support electrical components. The system is divided into 40, 60, 100 and 185mm systems. ...
	Wiener bus adapter features: Functional aspects The bus bar is made of copper or aluminum, which has high current density, small resistance and small skin effect, and does not need to be used for capacity reduction. The small voltage drop also means that the energy loss is small, which ultimately saves the user's capital. As far as the cable is concerned, because the cable core is a multi-strand thin copper wire, its root surface ...
	Ferromagnetic resonance occurs in the busbar system – Vernal The ferromagnetic resonance of the bus system is divided into parallel ferromagnetic resonance and series ferromagnetic resonance. Parallel ferromagnetic resonance refers to the resonance of the ground capacitance of the bus system and the nonlinear inductance of the bus electromagnetic voltage transformer (primary neutral grounding) in the neutral point ungrounded system or small current grounding system.
	What is tubular busbar and dense busbar - Wiener What is a tubular busbar Tubular bus bar is a kind of bus bar product with copper tube or aluminum alloy tube as conductor and external insulation. The tubular bus has the characteristics of high current (12000A), high mechanical strength, good insulation, wide application range, etc., ...
	Differences and differences between busway and other busbars The busbar and busway are actually one open and one closed, and the other is not closed. The closed busway is referred to as the busway, that is, the busway is sealed The closure of the busbar, the closure of the busbar and the busway all refer to the same east...
	The Wiener bus is a Siemens 3 VA1 and 3 VA2 adapter Wiener has developed a new series of 3 VA1 circuit breakers equipped with ® busbar adapters from Siemens in the 160 system with a compact range of 30. The safety articulation of the circuit breaker is the internal right of the tension spring device base and high-performance rails. ...
	Several faults of the Wiener bus system can be avoided Cause of bus failure 1. The inner network of the bus insulator and the breaker sleeve caused by the dirty appearance 2. The voltage transformer installed on the bus and the current transformer between the bus and the circuit breaker fail 3. Reverse gate ...