EFORT is one of the few domestic robot enterprises at the same time layout of the center parts, the whole machine development and engineering application of the ability of the manufacturer, independent center parts to create differentiated competitiveness and cost control ability, channel machine products are widely covered including new energy, 3C and other occupational needs and welding, ...

(1) ER130-4-2800: 1090 times/hour; (2) ER180-4-3200: 1090 times/hour; (3) The above two palletizing models are measured in the application scenario of rice bag palletizing: the palletizing cycle of the double gripper is about 1200 bags/hour, and the palletizing cycle of the single gripper is about 600 bags/hour. Influenced by different project layouts ...

Recently, the "OFweek 2022 China Intelligent Manufacturing Digital Innovation Summit and Veken Cup Industrial Automation and Digital Occupation" hosted by China's high-tech portal OFweek Veken · Industrial Control, OFweek Veken · Robot, OFweek Veken · Intelligent Manufacturing ...

Recently, Autorobot, a subsidiary of EFORT Robotics, received an order from the mass group for the purchase of the ID.3 pure electric car body panel and rear wheel cover welding line at the Wolfsburg plant in Germany, with a total project value estimated at about 241 million yuan (32.9 million euros). In 2017, Egypt ...

1. Install the robot in a safety fence without loopholes, so that personnel can be effectively prevented from entering the robot work area during the operation of the robot. 　　2. The safety door on the fence should be equipped with a safety latch and its locking mechanism, the safety gate must be opened by pulling the latch, and ...

1. Be sure to install the robot's control cabinet, operating panel and all other controls outside the safety guard (fence) so that the entire robot's range of motion can be monitored. 2. Confirm that within the range of motion of the robot arm, there are no personnel, packaging materials, etc.

1. In automatic operation, never enter or partially enter the safety fence. Also, make sure that there are no people or obstacles left in the safety fence before starting the robot. 2. In automatic operation, the robot is waiting for the timer delay or external signal input ...

1. Before entering the security fence, make sure that all necessary safety measures are in place and functioning properly. 2. Before entering the safety fence, please cut off the control power all the way to the main power supply. And place a clear signal to show that the shutdown and maintenance are in progress, and the locking or clamping ...

The robot is designed for safety functions in accordance with the safety requirements for robots used in industrial environments (GB 11291.1-2011/ISO10218-1:2006). 1. When transporting the robot, avoid exceeding the specified height. 2. If you need to lift the robot, you need to hook it with a wire rope ...

1. In automatic operation, never enter or partially enter the safety fence. Also, make sure that there are no people or obstacles left in the safety fence before starting the robot. 2. In automatic operation, the robot is waiting for the timer delay or external signal input ...

Before releasing the brake, make sure that the weight of the arm does not increase the pressure on the trapped person and thus increase any risk of injury. 1. Press the emergency stop button to confirm the status of the person and dial 120 in time. 2. Ensure that trapped people are not affected by rescue exercises.

1. In case of emergency, you can click the brake release function to release any axis of the robot. 2. For smaller robot models, the robot arm can be moved manually, but moving larger models may require the use of an overhead crane or similar equipment. Before releasing the brake brake, make sure that the arm weight ...

Security when the robot starts 　　1. When starting the robot, do not enter the safety fence unless the robot is disconnected. At the same time, please confirm that each safety guard is functioning normally before starting the robot. 2. When the robot is started and the operation is resumed from the failure state, ...

In order to meet the increasingly complex process and high-speed production needs of car electronics, new energy, 3C electronics and other occupations, EFORT launched a new heavy-duty desktop series robot to further expand the desktop robot product line. The heavy-duty desktop series robot wrist structure has extremely high rigidity and can be transferred ...

During the test, there may be design errors, teaching errors, and work errors in various elements such as teaching programs, fixtures, and logic controllers. Therefore, it is necessary to further improve safety awareness when conducting test runs. The following points need to be paid attention to during the commissioning process: 1. First of all, make sure ...

1) Workers must wear work clothes, safety helmets, safety shoes, etc. 2) When the power is turned on, make sure that there are no workers within the range of the robot. 3) The power supply must be cut off before entering the robot's range of action to operate. 4) Overhaul ...

The screen calibration function is used in the following scenarios: 1) After the teach-in firmware upgrade is completed and restarted, the screen needs to be calibrated. 2) Perform accurate calibration, but the calibration function appears to fail, and another round of screen calibration is required. 3) On the Teach Pendant screen, click ...

1) The operator must stand outside the working space where the robot is running; 2) The operator maintains a frontal view of the robot to ensure a safe way out in the event of an emergency; 3) Ensure that there are no personnel within the radiation range of the robot; 4) Check if the robot has an alarm, such as ...

This palletizing function is a palletizing process for customers to customize the palletizing type and hierarchical relationship, and several parts of the palletizing process can be used by setting several parts of the palletizing process and then combining them simply. There are three main parts of general palletizing, which are basic settings, process settings and production.

1. If possible, arrange for the recycling of lubricating oil and grease. Processed by authorized personnel/contractors in accordance with local regulations. 2. Do not dispose of lubricating oil and grease near lakes, ponds, ditches, sewers, or discharge them into the soil. 3. Incineration must be rooted in the root ...

(1) The motion control card is used to save the program data and firmware of related applications. The controller must be plugged into the appropriate motion card before it can run the application. In some applications, motion control cards can also be used to store machine data. (2) Be sure to use EFO ...