Tianyi switch - precautions for switching power supply to regulate current

Ambient air temperature: upper ambient air temperature +40°C; The lower limit of ambient air temperature is -5°C; The average temperature of the ambient air for 24 hours does not exceed +35 ° C. Altitude: The altitude of the installation site does not exceed 2000m. Atmospheric conditions: Atmospheric relative humidity at ambient air temperature of +4 ...

36V is a safe voltage, but it cannot be used as a standard for dividing high and low voltages. There are two ways to divide high and low pressure: 1. According to the rated voltage: the rated voltage is 1000V and below is called low voltage; The rated voltage of 1000V or more is called high voltage. 2. According to the voltage of the equipment to the ground...

(1) Green (HG, GL) What it means: stands for Safety, Normal, Readiness (i.e., an indication under safe operating conditions or the readiness of a mechanical device to start). Function: It is often used to indicate the state of equipment ready to start, all auxiliary components are in a state of preparation for operation, and various parts ...

Generation and transmission of electromagnetic interference There are two ways of electromagnetic interference transmission: one is conducted transmission and the other is radiated transmission. Conducted transmission is a complete circuit connection between the interference source and the sensitive equipment, and the interference signal is transmitted to the receiver along the connected circuit.

1. Install the dual power transfer switch with the power supply to ensure the correct access of the power supply. 2. Adjust the handle of the dual power transfer switch to the "automatic" position, so that the power supply will automatically detect the state of the other power supply, when one of the power supplies fails, the other power supply will ...

First, the reason for the fault of the induction circuit of the switch button indicator 1. Aging of circuit board: The circuit board of the switch button indicator induction circuit board may be aged if it has been used for too long, resulting in leakage in the circuit, and then the induction failure of the indicator light. 2. Sense ...

Unmarked/Z: Inductive/inductive self-diagnosis C/CZ: Capacitive/Capacitive Self-Diagnosis N: NAMUR safety switch X: Analog F: Hall V: Reed type J: Threaded cylindrical B: Cylindrical Q: Angular cylindrical shape ...

(1) The disconnector should have an obvious disconnection point, which is easy to identify whether the electrical appliance is disconnected from the power grid. (2) There should be reliable insulation between the disconnect points of the disconnector, that is, there should be enough distance between the disconnect points of the disconnector to ensure that it can work reliably under harsh climatic conditions, and ...

Q1: What is the difference between P switch and T switch? A: P switch is a load isolation switch, mainly used for the opening and isolation of the main circuit load, only 3P and 3+N, can add auxiliary contacts; The T-switch is a multi-function switch with a wide variety of contact sequences, modular contact units, which can ...

1. Buttons 1. Red Operation in hazardous situations. It is often used for emergency stops Stop and break. It is often used to stop all machines, stop one or more motors, stop a certain part of a piece of equipment, make the electrical components lose power, and have a stop function reset button. ...

1. Common air switch models in the family Common family models: DZ series, C16, C32. C40, C80, C100, C120 and other products, of which C represents the starting current, such as: C32 means that the starting current is 32A, which can drive a 6500 watt water heater, C40 ...

1. The high-voltage load switch can be broken with load and has the function of self-extinguishing arc, but its breaking capacity is very small and limited. 2. The high-voltage isolation switch is generally not able to break with load, there is no arc extinguishing cover in the structure, and there is also an isolation switch that can break the load.

First, the repair method The maintenance of a switching power supply can be carried out in two stages (1) When the power is cut off, it is "Look, Listen, Listen, Measure" Look: Open the power box, check whether the wire is disconnected, look inside the power supply, and find that the PCB substrate of the power supply is scorched or the components are cracked.

1 The contact is overheated Contact heat is mainly caused by the current flowing through the contact, and there is power loss between the contacts (such as contact resistance loss, arc energy loss). It is normal for the contacts to heat up, but severe heat (overheating) is a malfunction. The main ...

LW42 series LW42 series cam switch and safety switch are another series of high-quality products announced by Shanghai Tianyi Electric Appliance Co., Ltd. to meet customer needs. Device function: personal safety is paramount, LW42 series cam switch and safety switch unique terminal plan ...

1. Provide an electrical interval and a visible disconnection point during electrical equipment maintenance to ensure the personal safety of maintenance personnel [3] . 2. The disconnector can not be operated with load: it cannot be operated with rated load or large load, and it cannot be divided and combined with load current and ...

2P means two poles, which means that this air switch has two connection ports, one to connect to the neutral wire and one to the live wire, which is suitable for single-phase circuit connection, or can also be used to connect two-phase power supply in a three-phase circuit. 3P is the meaning of three poles, there are three connection ports, and all of them are ...

1. Repeated short-circuit test ◆ Test instructions The output of the module is short-circuited in various input and output states, the module should be able to achieve protection or retraction, repeated short-circuits, and after troubleshooting, the module should be able to automatically resume normal operation. ◆ Test Method a ...

1. When closing, first of all, attention should be paid to check that the circuit breaker that can be connected to the dual-power automatic transfer switch is indeed in the opening position, and then quickly operate the risk isolation switch to close it (whether the enterprise adopts manual management agency or leveraged financial institution personnel operation), but ...

1. What are the common faults? Answer: The common faults of the disconnector are: (1) The contact part is overheated. (2) Porcelain insulation damage and flashover discharge. (3) Refuse to pull and close. (4) Wrong pulling and closing. 2. The overheating of the contact part of the disconnector during operation is caused by ...