Model introduction of Tianyi cam switch

1. The high-voltage load switch can be broken with load and has the function of self-extinguishing arc, but its breaking capacity is very small and limited. 2. The high-voltage isolation switch is generally not able to break with load, there is no arc extinguishing cover in the structure, and there is also an isolation switch that can break the load.

1. Frame circuit breaker (universal type) - ACB: Rated current: In principle, frame circuit breakers are required for rated currents above 630A, and molded case circuit breakers are generally below 630A. It can be seen that the rated current of the frame circuit breaker is much larger, generally 630A-6300A. In addition in segments can ...

performance 1. Adopt double-row composite contacts, cross-connected mechanisms, micro-motor pre-energy storage and micro-electronic control technology, basically achieve zero arcing (no arc extinguishing cover); 2. Adopt reliable mechanical interlocking and electrical interlocking technology; 3. Adopt zero-crossing technology; 4、 ...

1. Differences in appearance Although these two types of switches seem to be very familiar, but there are still differences, half of the leakage protection switch is the same as the air switch, and the other half is not, it is equipped with a test jump button and a recovery button, which are not available in the air switch. 2 ...

(1) The disconnector should have an obvious disconnection point, which is easy to identify whether the electrical appliance is disconnected from the power grid. (2) There should be reliable insulation between the disconnect points of the disconnector, that is, there should be enough distance between the disconnect points of the disconnector to ensure that it can work reliably under harsh climatic conditions, and ...

How to use the indicator color correctly? 1. The indicator light (also known as the signal light) is mainly used to attract the attention of the operator or instruct the operator to carry out a certain operation in the way of bright indication, and as an indication that a certain state or instruction is being executed or has been executed. 2. General ...

1. After opening, establish a reliable insulation gap to separate the equipment or line that needs to be overhauled from the power supply with an obvious disconnection point to ensure the safety of maintenance personnel and equipment. 2. According to the operation needs, change the line. 3. It can be used to divide and combine small currents in the line, ...

(1) The cost of linear power supply is higher than that of switching power supply at a certain output power point. Therefore, with the development and innovation of power electronics technology, the switching power supply technology continues to break through and innovate.

1. How to wire the button switch with a light, there are a total of five binding posts on the button, and now you can only measure how to connect the power cord, but the light is on and I don't know how to connect. Answer: This situation is relatively simple, this kind of switch should be two terminals connected to the lamp, the other 3 terminals are switches, find out ...

LA42(V) series pushbutton switch is a new series of products independently developed by the senior technical team of VTeam Electric. It can be used in applications with rated insulation voltages up to 690V and nominal ratings of A600 (AC-15) and Q600 (DC-13). LA42(V) series pushbutton switches have a beautiful appearance ...

1. For vertical installation, the switch frame, closing mechanism, cable sheath, and protective steel pipe should be reliably grounded (not connected in series). 2. Before operation, several no-load opening and closing operations should be carried out, and each rotating part should be free of jamming, closing in place, and there should be enough safety distance after opening. ...

1. Use less plastic switches The switch is composed of a panel, a current carrier, a nozzle and a base, etc., and a good switch is mostly made of stainless steel inlay, which is safe and anti-electric shock. On the contrary, most of the inferior switches are made of plastic, although they are insulated, they are prone to leakage and flammability, and potential safety hazards will occur. 2 ...

An overview of limit switches Limit switch is a kind of mechanical orientation and electronic control interface, the mechanical action into electrical signals, is suitable for industrial environment of a common electromechanical and electrical components, through the contact way to detect the object, the existence and so on. It is possible to control the device's ...

1) Ambient air temperature: The upper limit of ambient air temperature is +40°C, the lower limit of ambient air temperature is -5°C, and the average value of ambient air temperature for 24h does not exceed +35°C 2) Altitude: The altitude of the installation site does not exceed 2000m. 3) Atmospheric conditions: Atmospheric relative humidity in the surrounding air ...

1. It can isolate the power supply, with a significant disconnection point, and is mostly used for fixed high-voltage devices; 2. It has arc extinguishing equipment and a certain opening and closing rate, and can pass through the normal working current and the specified short-circuit circuit in the case of closing; 3. It is forbidden to connect and cut off the circuit with load, ...

According to the different ways in which it is installed It can be divided into outdoor disconnector and indoor high-voltage disconnector. Outdoor disconnector refers to the disconnector that can withstand wind, rain, snow, filth, condensation, ice and heavy frost, etc., and is suitable for installation on terraces. According to the different structures of its insulating pillars ...

(1) Green (HG, GL) What it means: stands for Safety, Normal, Readiness (i.e., an indication under safe operating conditions or the readiness of a mechanical device to start). Function: It is often used to indicate the state of equipment ready to start, all auxiliary components are in a state of preparation for operation, and various parts ...

1. When the power is cut off for some reason and the power supply cannot be restored in a short period of time, the backup power supply must be enabled: (1) Cut off the circuit breakers of the mains power supply (including the circuit breakers of the control cabinet of the power distribution room, and the mains power cut-off of the dual-power switching box), and pull the double-cast anti-backing switch to the side of the self-provided power supply, ...

Conventional domestic travel switch LX19-001/111 in the LX19 series, LXK3-20S/T in the LXK3 series, JLXK1 series JLXK1-111/411/511 in the conventional travel switch are the most representative.

2P means two poles, which means that this air switch has two connection ports, one to connect to the neutral wire and one to the live wire, which is suitable for single-phase circuit connection, or can also be used to connect two-phase power supply in a three-phase circuit. 3P is the meaning of three poles, there are three connection ports, and all of them are ...