The causes and solutions of SIASUN robot servo motor overheating

It is necessary to incorporate carbon peak and carbon neutrality into the overall layout of ecological civilization construction, and take the momentum to achieve the goal of carbon peak before 2030 and carbon neutrality before 2060 as scheduled. ” 　　——Xi ...

1. Back up the controller memory 2. Regularly monitor SIASUN cobots, check robots, wiring harnesses and cables 3. Check the brake operation 4. Check the repeatability of SIASUN collaborative robots 5. Listen to too much vibration and noise 6. According to the specific new pine association ...

In the face of the severe situation of tightening global resource constraints, serious environmental pollution and ecosystem degradation, China has incorporated carbon peak and carbon neutrality into the overall layout of ecological civilization construction. In this context, we should further optimize the energy structure and use clean energy and renewable energy to achieve the goal of replacing traditional energy.

1. Joint robot debris cleaning (to ensure performance sustainability) When grabbing special substances, such as gyro-type substances, materials or dust may enter the inside of the machine tool loading and unloading manipulator, which will greatly reduce its working performance.

From August 18th to 21st, the 2022 World Robot Conference was held in Beijing Etrong International Convention and Exhibition Center. More than 130 robot companies and scientific research institutions brought more than 500 exhibits to the show, and more than 30 new products for the first time in the world were released at the conference site, showing the innovation of robot technology in the upstream and downstream of the whole industry chain.

1. The program requires that the program is used to take out the injection molding product and the material head, the manipulator stops above the injection molding machine mold and waits for the injection molding machine to open the mold, the starting position of the five electric shafts of the manipulator is 0, and the fixture is vertical. After the injection molding machine opens the mold, the manipulator takes out the finished product and the material head, and puts the material head into the crushing ...

1. The lifting capacity of the manipulator shall not exceed the lifting capacity. 2. Do not stretch out your hands, feet, or any part of your body when hanging. 3. Do not put your hands or fingers in the gap of the manipulator. 4. During operation, the face and hands should not extend to the upper part of the manipulator attachment. ...

The Gezhouba Water Conservancy Project is the first dam built on the Yangtze River, an important part of the Three Gorges Water Conservancy Project, and a milestone in the history of hydropower construction in China. On December 30, 1970, 80,000 soldiers and civilians held a ceremony for the commencement of the Gezhouba Water Conservancy Project.

There are four main types of drive mechanisms used in manipulators: hydraulic drive, pneumatic drive, electrical drive and mechanical drive. 1. Hydraulically driven Hydraulically driven manipulator usually consists of a hydraulic motor (various cylinders, oil motors), servo valves, oil pumps, oil tanks, etc.

1. When using the manipulator, clean and dry compressed air must be used. 2. This device is only allowed to be enabled when it is in good physical condition. 3. Check whether the corresponding load-bearing bolts are loose before use. 4. Before each use, check the equipment for wear or damage. In the absence of ...

There is a high degree of freedom, flexibility, and work from different angles and directions. Velocity up to 6 m/s, acceleration 10 m/s; High work efficiency, It is often seen on the Internet or TV, and it is more familiar and accepted by the world. The 6-axis robot is mainly used in ...

Manipulator alarm release method ▲When the step is temporarily stopped (automatic operation does not stop) 1. Check and dismiss the reason displayed on the alarm screen. ▲When an automatic stop alarm occurs (automatic operation stop) 2. Press the [Stop/Manual] button. ...

From October 26th to 29th, CeMAT ASIA, the annual industrial event in the Asia-Pacific region, was held at the Shanghai New International Expo Center. With the theme of "Smart Logistics", the exhibition showcases the innovative achievements of intelligent manufacturing and jointly creates a large ...

The Veken Cup is jointly organized by OFweek, a portal of China's high-tech industry, and OFweek, an authoritative robot professional media · robots· The final results of the OFweek 2021 China Robot Awards 2021 were presented on May 17.

1. Hands The hand is mounted on the front of the arm. The inner hole of the arm is equipped with a transmission shaft, which can be used to transfer the application to the wrist to rotate, extend and bend the wrist, and open and close the fingers. The structure of the manipulator's hand is similar to that of human fingers, and it is divided into three types: non-jointed, fixed joint, and free joint. Hand...

1. The action mode is set incorrectly. For example, a model with two products and a model with four products have different settings. 2. The whole machine is taken out and an alarm is issued, and it is fixed and stably taken out. This is caused by the adsorption assay pressure you have set too high. Need to reduce the detection ...

In any country, environmental problems arise because of development. China's target period from carbon peak to carbon neutrality is only 30 years, which is far shorter than the 50-70 years of developed countries in Europe and the United States.

Recently, Shanghai has implemented nucleic acid screening in batches with the Huangpu River as the boundary. In the closed and controlled area, the residential community implements closed management, and all enterprises implement closed production or home office. The epidemic and lockdown will undoubtedly face huge challenges for the manufacturing industry. Convener, nucleic acid ...

From August 31 to September 5, the China International Fair for Trade in Services, one of the four national exhibition platforms, was held at the China National Convention Center in Beijing. ® The dual-arm collaborative robot was invited to participate in the exhibition and was the first to be introduced at the Global Trade in Services Summit held on the evening of August 31.

　　1. When teaching, try to avoid standing between the robot and the workpiece or between the robot and the fixed object, so as to avoid the abnormal actions of the KUKA robot causing harm to the human body; 2. Pay attention to the teaching speed when teaching: When the robot is close to the welding gun, the welding gun should be taught at a lower speed. ...