1. Devices in static water (deep wells, pools, liquid irrigation, etc.)
1. When measuring the stop fluid level in the open container, put the liquid level transmitter vertically into the bottom of the container, and fix the cable connecting the transmitter and the junction box at the opening of the container.
2. When the viscosity of the medium is large (such as the sewage pool), a casing or bracket can be installed to ensure that the transmitter can be put into the bottom of the container.
3. When installing in the open air, the transmitter junction box should be placed in a ventilated and dry place as much as possible to avoid direct exposure and rain exposure from strong light, which will cause the shell body temperature to be too high or water to enter, and then damage the internal circuit board.
2. Underwater devices (rivers, rivers, lakes, etc.)
1. When measuring the water level in the flowing water, under the condition that the medium fluctuates greatly, a steel pipe can be inserted into the waterway, with an inner diameter of about 5 cm, and a number of small holes of about Φ5 are opened at different heights of the pipe in the reverse direction of the water flow to make the water enter the pipe, and the cable and junction box are fixed at the outlet of the pipe.
2. When the fluctuation of the waterway medium and the sediment are large, the sediment can also be filtered and the adverse effects of dynamic pressure and waves can be eliminated by installing damping devices to ensure the accuracy of measurement.
3. When the product is installed in a multi-lightning area, "lightning protection" should be indicated when ordering, and the user is required to install lightning protection devices on site, and ensure that the product and power supply are firmly grounded, which can reduce the probability of lightning damage to the transmitter.
|
More on that
|
The correct way to use linear position sensors – Turck
A linear displacement sensor is an electrical signal device that converts linear mechanical displacement into a linear or arbitrary function relationship through a potentiometer element. The potentiometer planned to complete the measurement of displacement intent must require a confirmation relationship between the change in displacement and the change in resistance. So so...
|
|
The cause of signal distortion measured by the sensor is Turck
In what ways does the signal fail to manifest Allah? Why is the signal unstable? Generally, the output signal is unstable due to transient temperature changes that cause the bias voltage to fluctuate and fluctuate. How to deal with it? A sensor with a stable bias voltage is used for processing.
...
|
|
Turck sensor classification
Sensors refer to equipment or devices that can sense the prescribed physical quantities and convert useful signals that can be used by the Great Wall according to certain laws. It generally consists of a sensitive element and a conversion element.
There are many ways to classify sensors, ...
|
|
The basics of sensors – Turck
First, the sensor industry
The national standard GB7665-87 defines the definition of sensors as follows: "A device or equipment that can sense the rules and be measured and converted into usable signals according to certain rules, usually composed of sensitive elements and conversion elements". A sensor is a detection device that can ...
|
|
The main role of torque sensors is Turck
Torque sensors are able to convert the physical change of torque into accurate electrical signals, which are mainly used in the power range, and have the characteristics of long service life, high accuracy and strong reliability.
Torque sensors are not common in our daily lives, but their use is very important. Currently, the twist ...
|
|
Laser displacement sensor selection method – Turck
1. Pay attention to the structure and data of the measured object, and the measurement of the general laser displacement sensor requires a complete triangular optical path. If the object to be measured has deep grooves or messy appearance, the triangular light path may be obstructed, making it impossible to measure. There are also some light-absorbing materials, such as black rubber and other materials, most of the light intensity will be ...
|
|
Turck's roller conveyor belt drives control Ethernet I/O modules
The Ethernet I/O module TBEN-LL-4RMC offers four Interroll EC5000 drum motor drive interfaces, which can control up to 48 motors and is capable of driving special motors up to 48V.
In addition, the module provides 4 digital input channels and 4 general-purpose digital channels ( ...
|
|
Turck temperature and humidity online monitoring sensor
Turck presents sensors for online monitoring of temperature and air humidity for online monitoring of the Industrial Internet of Things and sensor-to-cloud use.
Composite air humidity/temperature sensor for field or industrial IoT ...
|
|
Corrosion solutions for pressure sensors – Turck
Pressure sensors are used in all walks of life, especially in the industry, which uses a lot of pressure sensors, but the industry generally requires that the pressure sensor can be anti-corrosion, and the pressure sensor joint and cavity are made of imported stainless steel.
|
|
Three-wire connection for proximity switches – Turck
There is a difference between the two-wire system and the three-wire system of the proximity switch, and the three-wire system proximity switch is divided into NPN type and PNP type, and their wiring is different.
The wiring of the two-wire proximity switch is relatively simple, and the proximity switch is connected in series with the load.
|
|
Turck Ethernet IP67 fail-safe I/O modules
Turck's TBPN and TBIP complete fail-safe modules are field-based and function as safety logic controllers, thus helping customers in the modular planning and manufacturing of their machines.
Offline quiz security features to reduce ...
|
|
Common faults in pressure sensors – Turck
The first is pressure, and the transmitter can't afford to lose it. In this case, check if the pressure connector is leaking or clogged, if not, check the wiring method and check if the power supply is normal, the brief pressure to confirm if the output has changed, or if there is an output at the zero point of the sensor ...
|
|
In terms of industrial sensor selection – Turck
1. According to the measurement target and measurement environment
In order to carry out a detailed measurement work, it is necessary to first consider the principle of the sensor to choose, which needs to be analyzed and many elements can be confirmed. Because, even if the same physical quantity is measured, there are sensors with multiple principles to choose from.
|
|
How to debug Turck's pressure sensors
Turck's debugging method for turck pressure sensors is as follows: Using a controller with a 0.08-2MPa plan, requesting a pressure drop to 0.8MPa (down switching value) to announce the contact signal, the operation process is as follows:
Screw the product into the oil ...
|
|
Precautions for sensor use – Turck sensors
Precautions 1, in the use of the sensor to prevent contact with some corrosive or overheated media, this point is very important, if we do not pay attention to this point when using the sensor, it will affect the relevant use of the sensor.
Note 2: In ...
|
|
Introduction to laser displacement sensors – Turck
1. What is a laser displacement sensor?
Laser displacement sensors are sensors that use laser skills to measure. It consists of a laser, a laser detector, and a measurement circuit. Laser sensors are the new type of measurement. Able to accurately measure the orientation and displacement of the measured object without touch...
|
|
Calibration steps for pressure transmitters – Turck
When calibrating the pressure, we need to zero the current of the transmitter, and then carry out the positive and negative relocation of the zero point according to the requirements, if the pressure transmitter is calibrated for the first time, then we also need to add the measured physical quantity calibration, and the subsequent calibration can be calibrated by manual operation.
...
|
|
Advantages of eddy-current displacement sensors – Turck
The cutting-edge technology of modern science and technology, and its horizontal concave and convex are also one of the important indicators to measure the level of scientific and technological development of a country. There are many kinds of displacement sensors on the market, such as eddy current displacement sensors, which are widely used in various industries. So what are the advantages of eddy-current displacement sensors ...
|
|
Turck sensor technology
1. Capacitive pressure sensors are usually loved by many OEMs to test the capacitance changes between the two appearances, so that the sensors can sense extremely low pressure and vacuum levels. In our typical sensor configuration, the tight shell consists of two golden appearances, metal ...
|
|
The load cell measures the magnitude of the external gravity
(1) The shape of the elastomer element should be as regular as possible, generally rectangular and circular. During the measurement process, conventional elastomers can be identified by sensors more easily and accurately.
(2) The surface process should be precise and the density should be very uniform. Elastomers as part of the main force ...
|
|
Contact
working hours
