The difference between Kunlun Tongtai touch screen programming software version 7.7 and version 7.6

Inaccurate screen position: Repositioning can be done via driver software. Touch position and screen cursor upside down: When installing the touch screen, the position of the screen is reversed, please adjust the touch screen position according to the principle of right-hand position out. The touchscreen display icon keeps pointing towards the fixed ...

Since infrared touch technology is the trend of contacting products in the future, when will infrared technology become mainstream? At present, the touch screen technology widely used in the market is mainly resistive technology touch screen, capacitive technology touch screen, and infrared technology touch screen. If the use of resistors becomes longer, it will ...

1. Surface acoustic wave screen The three corners of the acoustic screen are pasted with transducers that transmit and receive sound waves in the X and Y directions respectively (transducers: made of special ceramic materials, divided into transmitting transducers and receiving transducers. It is to convert the electrical signal sent by the controller through the touch screen cable into sound.

1. The resistive touch mouse only moves in a small area or the resistive touch screen is not allowed This usually happens when you install the driver for the first time, so please run the touchscreen calibration procedure. The touchscreen calibration procedure must also be run after changing the display resolution (Start – Procedure) 2 ...

56. Does TPC support OPC communication? No, the network version supports OPC communication. 57. 200PLCLC communication wiring with TPC7062K (1) The 7 positive and 8 negative of the TPC RS485 interface is connected with the positive and 8 negative of the PLC serial port 3, and the wiring diagram is as follows: TPC PLC 58. 200 ...

After receiving the touch signal, the capacitive touch screen converts the touch data into electrical pulses and transmits it to the touch screen control IC for processing. The signal is amplified by a low-noise amplifier (LNA), then converted and demodulated by analog-to-digital ratio, and finally sent to a DSP for data processing. Electricity...

Advantages of the all-in-one touch screen machine: 1. The touch screen all-in-one machine can complete wireless screen projection, which means that there is no need to spend time connecting and debugging equipment, and everyone can project the content to the touch screen all-in-one machine through their laptop, mobile phone or tablet. Open batch ...

20. The TPC project running environment is automatically restarted If the CPU usage reaches 99% during the project runtime, the runtime environment will automatically exit and then restart. There may be many reasons for high CPU usage: too many bitmaps, too many scripts in the loop policy, and short cycle times. ...

Communication failures are generally due to three factors (1) Communication parameters, such as the COM number of the serial port, baud rate, etc., the IP address of the network port, etc. (2) Communication line, such as RS232 communication, the result is RS485. For example, it is directly connected to the network port, but it is connected to the cross. （3 ...

The most far-reaching technological change in touchscreen performance is the shift from resistive to capacitive touchscreen technology. According to iSuppli, a market research agency, nearly 25% of touchscreen mobile phones will be transferred from resistive to capacitive touchscreens by 2011. Capacitive touch screen technology brings ...

On May 20, 2015, the "Kunlun Tongtai 2015 Seminar" entered the Ningbo Marriott Hotel. The Kunlun Tongtai Seminar departed from Hangzhou Station and once again stood in East China. By 2015, Kunlun will further expand to the East China market, and Ningbo is naturally one of the key development cities. ...

1. Stuff preparation 1. 1 Phillips screwdriver; 2. 1 small slotted screwdriver; 3. 1 hair dryer; 4. Several transparent double-sided tapes. Second, the old screen is dismantled 1. Use a Phillips screwdriver to remove the 6 screws on the back cover and open the back cover. 2. ...

The McgsPro architecture is divided into three parts: configuration environment, simulated operation environment, and operation environment. The configuration environment and the simulated operating environment are equivalent to a complete set of tools and software, which can be run on a PC. Users can ...

TPC1561HI common fault phenomenon of Kunlun Tongtai touch screen operation panel (1) Black screen, blurred screen, white screen (2) Caused by the aging of the LCD screen, the high voltage is low, and the lamp is aging (3) The LCD screen has no display, and the brightness is not clear (4) LCD screen display vertical bar, display ...

First of all, on the back of the Kunlun Tongtai touch screen, determine the specific model of the Kunlun Tongtai touch screen. Open the Kunlun Tongtai touch screen programming software, click [File] in the menu bar and open it. In the File drop-down menu, select Project Settings In the pop-up Modify Project ...

First of all, on the back of the Kunlun Tongtai touch screen, determine the specific model of the Kunlun Tongtai touch screen. Open the Kunlun Tongtai touch screen programming software, click [File] in the menu bar and open it. In the File drop-down menu, select Project Settings In the pop-up Modify Project ...

Accuracy: Accuracy can be defined as the maximum positioning error in a predefined touchscreen area, measured in the straight-line distance between the actual position of the finger and the measured position. When measuring accuracy, a simulated or mechanical finger is used. A finger placed on the panel ...

The difference between capacitive screen and resistive screen is different in its working principle, touch technology, use environment, cost and life, and then I will explain it to you in detail: How it works Capacitive touch: works by using the body's current induction. When the finger touches on the metal layer ...

What is the reason why the variable cannot be deleted? Use the Usage Count Check command to check variable usage, and then you can delete variables that aren't being used. If a variable cannot be deleted, it means that the variable is in use and cannot be deleted. Is it possible to view the device while it is running?

1. Tap the settings icon in the top right corner of the screen to enter the settings menu. 2. Find the "Time Settings" option in the menu and click to enter. 3. On the time settings screen, you can manually modify the current date and time. There is also the option to automatically get the time so that the device ...