Measuring pre-work with vibration sensors – ifm

The IF Design Award is held annually in Hannover, organized by iF Design GmbH, the world's oldest independent design agency. In 2020, 3 ifm products stood out from many competitors and won ...

Diagnose sensor faults based on mathematical models? When there is a problem, the first time is to diagnose it, see where the problem is, so that it is easy to deal with, from different angles, we use more than one method when diagnosing the problem, if this is classified, it can be divided into two ...

Sensor detection is known to prevent disturbances. Once disturbed, the sensor may be damaged, the measurement system will be affected, the inaccurate data will affect the future use, the judgment will be biased, and the impact can be large or small, so anti-interference is very important. Today we're going to comment ...

Pick the right adhesive! We need to know the importance of adhesives, many people do not pay attention to the selection of adhesives, the natural frequency of the accelerometer is determined by the degree of coupling of the bond, so it is important to choose the right adhesive. The weight of the accelerometer is also what we have to test.

1. Encoder own problem: It refers to the problem of the encoder's own components, resulting in its inability to generate and output correct waveforms. In this case, the encoder needs to be replaced or its internal components repaired. 2. Encoder connection cable problem: the probability of this problem is high, and the maintenance is under repair.

1. When the pressure goes up, the output of the transmitter can't go up. In this case, you should first check whether the pressure connection is leaking or blocked. If you admit that it is not, check the wiring method and check the power supply, if the power supply is normal, then briefly pressurize to see if the output changes, or observe the zero position of the sensor ...

ifm flow sensor solutions. IFM Flow Sensor SV5200, Vortex Flow Sensor with User Friendly Display, Circuit Connection Can Be Rotated for Optimal Arrangement, With Switching Output or Frequency Output, and IO-Link for Reliable Flow Detection ...

IFM sensors are widely used in electromechanical control systems due to their high sensitivity, low output impedance, simple structure, strong anti-interference ability, high output power and high measurement accuracy. So how should we maintain it during use? Here's what we'll do for you...

Not all damaged bearings can be corrected, but the cause and extent of the damage to each damaged bearing must be evaluated to prevent or reduce further damage before considering the correction or replacement of a new bearing. There are many reasons for bearing damage, such as improper equipment, dirt invasion, etc.

According to the measurement method, it can be divided into two categories: touch type and non-touch type. 1. Touch type The detection part of the touch temperature sensor has an outstanding touch with the measured target, also known as a thermometer. The thermometer reaches thermal equilibrium by conduction or convection, so that the thermometer indication ...

The aluminum foil sensor is composed of elastomer, strain gauge, adhesive, maintenance layer, compensation circuit, etc. The strain transmission path is: elastomer - + adhesive → strain gauge sensitive grid - + overlay - maintenance coating, which constitutes a complex system that is more different from the strain gauge itself. If the application attached to the elastomer ...

Easy-to-install sensor with long-service life electronic GMR unit – flush unit This sensor can be conveniently installed in a C-slot Fixed at the end of the housing for stable elastic stress relief A variety of ...

There are two types of accelerometers: one is the angular accelerometer, which is improved from the gyroscope. The other is a linear accelerometer. It can also be divided into single-axis, dual-axis and three-axis accelerometers according to the measurement axis. ...

Torque sensor is a component that must be installed in some industrial products, mainly used to measure speed and viewpoint orientation, but different types of sensors have different ways to use and function, what is the classification of torque sensor? Resistance strain ...

Capacitive sensors can detect any object without touch. In contrast to inductive sensors, which can only detect metals, capacitive sensors are also capable of detecting non-metallic materials. principle 1. The first thing to be measured is ...

1. S-type load cells are moderately priced and suitable for mass production - good sensor consistency is required, suitable for automated batch production, and high requirements for processing equipment to eliminate inconsistencies and faults formed by manual operation. 2 ...

Photoelectric switch (photoelectric sensor) is the abbreviation of photoelectric proximity switch, which uses the shielding or reflection of the beam by the detected object to connect the circuit by the synchronous loop to detect the presence or absence of the object. When the photoelectric sensor outputs the signal, the signal is occasionally unstable, and many people do not know what to do.

Thanks to a uniquely adjustable sensor, it can be flexibly adapted even in wet environments ●After touching the sensor, the ergonomic plan is selected for work ● Open delay can prevent unintentional opening ...

Principles of the control system of IFM controllers: The IFM ifm controller is a process that continues to detect the unit to be manipulated (control variable x) and compares it with the reference variable w, and according to the results of the comparison, the control variable is affected to get used to the reference variant. In most cases, ...

1. Oxygen sensor poisoning. Oxygen sensor poisoning is a common and difficult problem to prevent, especially in cars that often use leaded gasoline, and even new oxygen sensors can only operate for a few thousand kilometers. If it's just a subtle case of lead poisoning, then use a box of lead-free ...