1: What is the difference between servo motor and general motor?
The biggest difference between servo motors and general motors is the motor rotor and reaction equipment. The surface of the rotor of the servo motor is pasted with a strong magnetic plate, so that the magnetic field generated by the stator coil** can control the orientation of the rotor, and the acceleration and deceleration characteristics are much higher than those of ordinary motors. The reaction equipment can be oriented to the servo drive of the reaction motor rotor, and the commonly used reaction equipment of the servo motor is optical encoder, resolver, etc.
2: Can the input power supply of the servo drive be connected to a single-phase 220V?
Delta servos can be connected to single-phase/three-phase 220V power supply below 1.5KW (inclusive), and only three-phase 220V power supply can be connected to 2.0KW (inclusive) or more. The quality of the DC waveform rectified by the three-phase power supply is better, the DC power supply of bad quality will consume the energy of the capacitor on the bus, and the capacitor will charge and discharge the bus to insist on the stability of the bus voltage when the motor accelerates and decelerates rapidly, so the characteristics of the three-phase power input servo will be better than that of the single-phase power input servo, and the current provided by the three-phase power input is also greater.
3: Is it possible to exchange the UVW three-phase output from the servo drive to the motor?
No, the connection between the servo drive and the UVW motor is **. Generally, when the input power supply of the asynchronous motor UVW is exchanged in two phases, the electric timing is reversed, in fact, any two-phase exchange motor of the servo motor UVW will also be reversed, but the servo motor has a reaction device, so that the positive reaction will cause the motor to fly. The servo drive will detect and avoid flying, so what we see after the UVW is connected to the wrong wire is that the motor turns an angle at a very fast speed and then alarms the ALE06 for overload.
4: Why does the servo motor need to be servo on before it can operate?
The servo drive does not output current to the motor when it is energized, so the motor is in a relaxed state (the hand is able to turn the motor shaft). After receiving the Servo on signal, the servo drive will output the current to the motor, so that the motor is in a situation of electrical insistence, and only then can it receive the instruction to act, and it will not act when the instruction is not received, even if there is an external force to intervene (the hand does not move the motor shaft), so that the servo motor can complete the first positioning.
5: How to deal with the alarm ALE14 when the servo drive is powered on?
The ALE14 is a forward limit anomaly alarm, because the maintenance DI points such as the forward and reverse limits set by the factory parameters and the urgent abort are normally closed contacts, and will alarm when there is no signal. When the upper controller has connected these maintenance signals or may not need these maintenance signals, the alarm can be eliminated by the following methods: the parameter P2-15 is set to 122 or 0, or the DI point may be shorted directly.
6: How to deal with the alarm ALE11 when the servo drive is powered on?
The causes of ALE11 alarms are: encoder wire wiring error, motor encoder fault, driver hardware fault.
7: How to deal with the alarm of servo drive ALE06?
The causes of the ALE06 alarm are: the UVW line connection phase sequence is wrong, the load is too large, the gain setting is too high, and the motor encoder is abnormal. After the parameter P0-02 is set to 11, the uniform load rate of the servo motor can be supervised on the drive panel, if the uniform load rate continues to be more than 100%, the overload alarm will be presented, and the overload characteristics of different motors can be found in the technical manual.
8: How to deal with the alarm ALE09 of servo drive?
The reasons for the ALE09 alarm are: insufficient motor output due to lack of phase of UVW wiring, low gain setting, low torque constraint, high command frequency or too large electronic gear ratio causing the motor to reach * high speed constraint (P1-55), motor encoder failure.
9: What is the reason why the motor is still running after the pulse command is completed?
The pulse command slip parameter P1-08 is set too large, resulting in a severe lag in the command, and the motor is still running after the command is completed. The operation of the motor can be seen through the built-in oscilloscope function of Delta's servo software to monitor the command pulse and the encoder response pulse. When the electronic gear ratio setting ratio is larger, the appropriate setting parameter P1-08 can make the motor run more smoothly.
10: How to deal with the alarm of servo drive ALE04?
When the AB series servo drive is equipped with ECMA motor, the power mismatch will alarm ALE04 when it is powered on, in addition to this case, the alarm ALE04 will be caused as soon as it is powered on, which is the fault of the motor encoder. If the ALE04 alarm is displayed during use because the encoder signal is disturbed, check whether the encoder wire is shielded twisted pair, whether the ground wire between the driver and the motor is connected, or whether the encoder wire is covered with a magnetic ring. After ALE04.EXE software, it can monitor whether the AB pulse count of each Z-pulse azimuth changes, and will alarm if there is a change.
|
More on that
|
Delta's method of reducing the number of inverter repairs
Inverter is a modern factory in the use of a very ubiquitous equipment, this is a new type of equipment, the price is very noble, and the price of inverter repair is also very expensive, so in the process of using inverter, pay attention to the use of inverter, on the one hand, inverter, delay inverter ...
|
|
What are the problems of the inverter if it is not used for a long time - Delta
Most inverter brand products can rely on the heat of internal electrical components to remove moisture during normal use. If you don't use it for a long time, it's easy to get wet. The chip pins, penetrating resistors, capacitors, and inductor pins of the DIP package will be severely rusted or desoldered, resulting in on-resistance ...
|
|
Requires an inverter speed control application – Delta
Inverter is a kind of speed regulation equipment, where is there a place to use motor speed regulation, especially asynchronous motor speed regulation, will use inverter, now it is mainly used in industrial equipment on a large scale, because the motor is the heart of industry, and three-phase asynchronous motor occupies the vast majority of the share, ...
|
|
Inverter Fault Repair Test Method - Delta
Static quizzes
1. Test the rectifier circuit
Find the P and N ends of the DC power supply inside the inverter, adjust the multimeter to the resistance X10 gear, connect the red watch rod to P, and separate the black watch rod to R, S, T. Instead, connect the black watch rod to the P...
|
|
Several common problems of Delta and their solutions
What is the stall prevention function of the inverter?
If the given acceleration time is too short, the output frequency of the inverter changes much more than the change of speed, and the inverter will jump due to the flow of overcurrent, and the free operation is stopped, which is stalling. In order to prevent stalling and keep the motor working, ...
|
|
Precautions for the use of transformer DC resistance tester - Delta
The transformer DC resistance tester uses the 32-bit ARM core as the processing center to control the whole machine, actively complete the functions of self-calibration, current stabilization judgment, data processing, resistance value display, etc., and can measure the DC resistance of various types of transformers and transformers.
...
|
|
The specific operation method of Delta inverter
(1) When the speed of the motor is controlled by the Delta inverter, the noise and temperature rise of the motor are higher than that of the frequency of the motor. When the motor is working at low speed, due to the low speed of the motor blades, the temperature rise of the motor becomes high.
|
|
Installation requirements for inverter energy consumption braking - Delta inverter
(1) The wiring interval between the braking unit and the inverter, as well as between the braking unit and the braking resistor, should be as short as possible (the wire length should be less than 2m), and the wire cross-section should meet the requirements of the braking resistor discharge current.
(2) The brake unit is working ...
|
|
Inverter performance test method - Delta
As we all know, the inverter has many maintenance functions, such as overcurrent, overvoltage, overload maintenance and so on. With the continuous improvement of industrial automation, frequency converters have also been widely used. This article will explain to you how to use a multimeter to measure the quality of the inverter.
Need...
|
|
Inverter setting method - Delta
The first step is type recognition: acknowledging whether the type of inverter is common to the type of inverter purchased. If not, ask the agent to return the item.
Step 2: Shipping Acknowledgement: After opening the package, check whether the inverter is damaged during transportation. If there is damage, let the agent return ...
|
|
Delta's Ultron NT series UPS escorts flight safety at international airports
The rapid development of the national economy has opened up a broad shopping mall space for the growth of the civil aviation industry. In order to meet the surge in the number of flights, an international airport in Northwest China has invested in the third phase of the expansion project, and has been listed as the "number one project" for civil aviation development and the "benchmark demonstration project" for national civil aviation.
|
|
Basic parameter setting of special inverter for wind turbine - Delta
1. Control mode:
i.e. speed control, torque control, PID control or other methods. After the control method is adopted, static or dynamic identification should generally be carried out according to the control accuracy.
2. Minimum operating frequency:
That is, the minimum speed of the motor. When the motor is working at low speed, the ...
|
|
Introduction of incoming reactor for inverter - Delta
Reactors are also called inductors, and when a conductor is energized, a magnetic field will be generated in a certain space scale occupied by it, so all electrical conductors that can carry current have inductance in a general sense. However, the inductance of the energized long straight conductor is small, and the magnetic field generated is not strong, so the actual reactor is conductive.
|
|
Measures to avoid soft failure of inverters - Delta
The ways to reduce the soft fault of the inverter are: 1. Detect the overvoltage and undervoltage of the inverter; 2. Detecting overcurrent is the most frequent phenomenon of frequency conversion alarm.
Generally, the overvoltage alarm is generally presented at the time of shutdown, and the primary reason is that the deceleration time is too short or the braking resistance and braking unit have ...
|
|
Servo motor speed improvement method - Delta
When many engineers debug servo motors, they often have such a problem: why is my servo motor so slow, how can I improve the speed, and how much can the maximum speed reach? The basis for the confirmation of the speed method of the servo motor: the speed of the servo motor.
...
|
|
Delta's inverter process setting
1. Restore the inverter to factory settings, press the "ENTER" button to enter the parameter setting interface, and press it continuously until it is 00-00 and then stop. Press the number up button to change to 00-02. Press the "ENTER" key again, the panel value will show 0, press the number up key to change it to 9. Press the "ENTER" key, break ...
|
|
How to choose Delta's servo motor
When selecting a Delta servo motor, in principle, the selection should be based on the load conditions. There are two types of loads on the motor shaft, namely damping torque and inertial load. Both loads should be calculated correctly and their values should meet the following criteria:
1) When the machine is running with no load, in the whole speed range, Delta ...
|
|
Precautions for inverter selection - Delta
The selection of the inverter is mainly determined by the load characteristics of the drive and the actual working current of the motor, in addition to the following precautions:
1. The environment is suitable for some high temperature (higher than 50 degrees) and high altitude (higher than 1000 meters).
|
|
Analysis of misunderstandings in the application of Delta inverters
The capacity selection of the inverter is based on the rated power of the motor
Myth: The capacity selection of the inverter is based on the rated power of the motor
Compared with the motor, the price of the frequency converter is the most expensive, so under the premise of ensuring safe and reliable operation, the frequency conversion can be reasonably reduced.
|
|
Composition and function of Delta inverter
Delta inverter is a device that converts the power supply (50Hz or 60Hz) into AC power supply of various frequencies to realize the variable speed operation of the motor.
|
|
Contact
working hours
