1. Support welding under the guidewire:
According to the direction of the movement of the buoy of the level gauge, determine the position at the bottom of the container, and fix the guide bracket (piece 1) under the welded or riveted steel wire
2. Install the guide rail joint.
(1) Draw the steel wire vigorously and fix it at the lower support, taking care not to bend or knot the steel wire, so as not to affect the lifting of the buoy.
(2) The guide wire passes through the guide wire hook of the buoy, penetrates the hook screw (piece 6), fixes the end of the wire rope and clamps it with a wire chuck, tightens the hook nut to make it in a fastened state, and then tightens the upper nut to avoid loosening, and then closes the cover.
(3) The two guide ropes should be perpendicular to the ground and parallel to each other, ensuring that the spacing is 300mm.
3. Install the ruler.
When the user orders, according to the measurement range it provides, determine the length of the ruler, and the installation requirements:
(1) The connecting parts on the ruler should be straight, smooth and without protrusion, so as not to affect the normal operation of the hammer pointer or cause measurement errors.
(2) The ruler should be perpendicular to the surface of the liquid in the tank, and there should be no inclination, and the verticality of the ruler installation should not be greater than 5°, otherwise the hammer pointer will be stuck, resulting in measurement failure.
(3) When welding the ruler tripod (11), the mounting surface should be on the same plane as far as possible, and the mounting hole should be on the same straight line, that is, the scale surface of the ruler and the guide on both sides of the hammer pointer should be straight, so that the hammer pointer can be flexibly lifted in the horizontal direction of the ruler.
Note: The distance between the two ruler tripods is 1 meter.
4. Steel wire and hammer pointer for pontoon connection:
One end of the pontoon and the connecting steel wire is clamped and fixed with a wire, and then the other end of the connecting steel wire is loaded into the two guide pulley boxes that are installed in advance, and is connected with the hammer pointer, and is clamped and fixed with a wire, and the guide pulley bracket is adjusted after zui, so that the connecting steel wire is perpendicular to the horizontal direction, so that the pontoon moves flexibly on the guide wire, has a light and slippery feeling, and has no stuck, twisted, skidding, skidding, slipping and other phenomena.
Note: Master the required length of the wire.
|
More on that
|
RKG thermostat - an introduction to the characteristics of digital displays
1) It is a display of the common cathode. It uses the principle of the positive electrode as the segmented input, with the ground wire as the common output, and the segmented input is valid as a high-level input.
2) It is a display with a common anode. It uses an anode as an aggregate input, and in contrast to the common cathode, the segment is effective at a low level output ...
|
|
Common faults and solutions of RKC temperature controllers
1. The power indication is normal, but the temperature controller has no screen display. Most of this fault is caused by the heating of the voltage regulator element (7805 or 7812) on the thermostat during long-term use, which leads to the breakpoint of the solder joint, and sometimes it is caused by the phenomenon of virtual soldering at the factory, and the main re-soldering can be done.
2. Temperature controller ...
|
|
How to set the parameters of the RCRS400 thermostat
1. Set temperature: Press the SET button to set or view the temperature set point. Press the SET key digital tube characters to start flashing, indicating that the instrument has entered the setting state, press the △ key to increase the set value, press the ▽ key to decrease the set value, press and hold the △ key or ▽ key The data will change rapidly, press the SET key again ...
|
|
RHK thermostats – an introduction to the classification of displays
(1) Categorize by display color
1. Monochrome display
There are two types of displays: multi-grayscale monochrome display and VGA multi-frequency monochrome display. These displays are small, lightweight, clear and inexpensive, making them suitable for highly mobile workplaces.
2. Color ...
|
|
RKC Thermostat – What are the common faults of thermostats?
1. There is no manifestation when the power is on. For this kind of problem, first confirm whether the power supply is there and whether the power supply matches the power supply required by the thermostat, and then check whether the wiring is strong. The problem is still there, then it is the problem of the thermostat itself.
2. There is a manifestation, and the manipulation makes mistakes. The first thing to look at this kind of problem is to look at the control ...
|
|
RLC thermostat - a classification introduction of floor heating thermostats
Floor heating thermostats can be divided into digital thermostats and analog thermostats according to different input and output forms. Digital thermostats generally have liquid crystal display or digital tube display panels, and set and control the temperature through buttons, while analog thermostats generally use knobs or slider band wave wheels to set ...
|
|
RKC Thermostat – How to Maintain the Instrument?
The normal operation of the instrument is inseparable from the on-site maintenance relationship, especially some important process links, once there is a leak, it will greatly affect the quality of the product, resulting in heavy losses.
First of all, it is common to install both remote and field-indicated level gauges on important tanks.
|
|
RDC converters – a classification of power converters
Motors are divided into two categories: DC motors and AC motors, and AC motors are divided into asynchronous motors and synchronous motors, and their respective speed regulation principles are also different. According to the speed regulation requirements of the motor, it can be divided into two categories: DC power converter and AC power converter:
...
|
|
RLC thermostat - a detailed explanation of dry-type transformer thermostats
The working principle of dry-type transformer thermostats
The dry-type transformer temperature controller is a new generation of controller designed for the safe operation of dry-type transformers. The controller adopts single-chip microcomputer technology, and uses three platinum thermal resistors embedded in the three-phase winding of the dry-type transformer to detect and display the transformer.
|
|
RRKC thermostats – about output and control performance
When using a temperature controller to control a heater, it is necessary to convert the control calculation results of the temperature controller into electricity and apply it to the heater. Electromagnetic relays, solid state relays or phase controllers are usually used for conversion. Depending on the conversion method, the output of the temperature controller is different ...
|
|
RLC thermostat - common faults and solutions of intelligent temperature controllers
1. Heating for a period of time, the temperature does not change. Displays the ambient temperature of the site at all times (e.g. room temperature 25°C)
In case of such failures, first check whether the SV value setting value is set, whether the instrument OUT indicator is lit, and whether the No. 3 and 4 terminals of the "multimeter" measuring instrument have 12VDC output.
|
|
RKC thermostat - how to keep the line when installing the thermostat?
First, the selection of the orientation of the thermostat device
1. Easy to operate locally;
2. It can include the average temperature of the local area;
3. Localities with more human activities;
4. It can avoid cold and heat sources;
That is to say, the orientation of the device should be far away from radiators, away from doors and windows...
|
|
RKC Thermostat – How can a thermostat be broken?
First, the temperature does not appear
1. Fault with the temperature sensor
If the temperature probe of the temperature sensor breaks or the wire is broken, the sensor does not have a digital display when the temperature sensor is connected, but only shows the "----" and sounds an alarm.
|
|
RLC Thermostat – Precautions for Thermostat Operation
1) Measure the function
Its temperature measurement scale is mainly between -20 °C and 80 °C, and the humidity measurement scale is mainly between 20% RH and 99% RH. In addition, it has a temperature resolution of 1°C and a humidity of 1%RH.
2) Parameters and data display functions
Temperature and humidity control ...
|
|
RKC converter - an introduction to the classification of converters
Analog-to-digital converters
The analog-to-digital converter comprises a first transmission circuit, which receives an input voltage and an output clock signal, which is phase-shifted, depending on the input voltage, and a second transmission circuit receives a reference voltage and an input clock signal, and outputs a reference clock signal, which ...
|
|
RKC thermostat - what are the anti-interference measures of the instrument?
1. Electromagnetic induction (refers to the coupling of magnetism). There is a strong alternating magnetic field in the surrounding space of high-power transformers, AC motors, high-current power grids, etc., and the closed loop formed by the lines of the control system (detection, transmission, conversion, regulation, calculation, execution, auxiliary, display, etc.) is located in the ...
|
|
RKC Level Gauge - the principle of the selection of float level gauges
The float level gauge is widely used, mainly used in petroleum processing, food processing, chemical industry, water treatment, manufacturing, electric power, papermaking, metallurgy, ships and boilers and other industrial automation processes to measure and control the level.
1. Pay attention to the specific working conditions. As introduced ...
|
|
For some considerations in the RKG thermostat setup
RKC Thermostat Operation Note:
1. Clean the instrument only after the power is off;
2. To remove the stains on the monitor, please use a soft cloth or cotton paper;
3. The display is easy to be scratched, and it is forbidden to use hard objects to operate the panel buttons, otherwise the buttons will be damaged or scratched.
RLC thermostat ...
|
|
Initialization parameter setting of the rkc thermostat
1. Press the ISET) button for 2 seconds to enter the parameter setting mode, press ISET until "LCK" is displayed, press the [] key to move the cursor to the thousands, and press the [] button to change the number of thousands from "0" to "1" to display "1000" to unlock.
2. Press the ISET button for 3 seconds to return to SV/PV display mode
3. Press [SET]+ ...
|
|
Common faults and analysis of thermostats
Common faults of thermostats
1. There is no display when the power is on. This type of problem first determines whether the power supply is available and whether the power supply matches the power supply required by the thermostat, and then checks whether the wiring is secure. The problem is still there, then it is the problem of the thermostat itself.
2. There is a display, and the control is wrong. This...
|
|
Contact
working hours
