How Rexroth vane pumps work:
1. Single-acting vane pump
The pump is composed of parts such as rotor 1, stator 2, blade 3, oil distribution pan and end cover. The inner surface of the stator is a cylindrical hole. There is eccentricity between the rotor and stator. The blade can slide flexibly in the groove of the rotor, and under the action of the centrifugal force when the rotor rotates and the pressure oil that enters the root of the blade, the top of the blade is attached to the inner surface of the stator, so that a sealed working cavity is formed between the two adjacent blades, the oil distribution plate, the stator and the rotor. When the rotor rotates in the counterclockwise direction, the blade on the right side of the figure stretches outward, and the volume of the sealing working chamber gradually increases, and a vacuum is generated, and then the oil is sucked in through the upper window of the oil suction port 6 and the oil distribution plate 5. And on the left side of the diagram. The blade is indented inward, and the volume of the sealing chamber is gradually reduced, and the oil in the sealing chamber is pressed out and output to the system through another window of the oil distribution pan and the oil pressure port 1. This kind of pump sucks oil and presses oil once in the process of one rotation of the rotor, so it is called a single-acting pump. The rotor is subjected to radial hydraulic unbalanced forces, so it is also called unbalanced pump, and its bearing load is large. The displacement of the pump can be changed by changing the eccentricity between the stator and the rotor, so this kind of pump is a variable pump.
2. Double-acting vane pump
Its working principle is similar to that of a single-acting vane pump, except that the stator surface is composed of eight parts: two long radius arcs, two short radius arcs and four transition curves, and the stator and rotor are concentric. Under the circumstance that the rotor rotates clockwise, the volume of the sealing working chamber gradually increases at the upper left corner and the lower right corner, which is the oil suction area, and gradually decreases at the lower left corner and the upper right corner, which is the oil pressure area; There is an oil sealing zone between the suction zone and the pressurized zone to separate them. The rotor of this pump rotates once and each sealed working chamber completes oil suction and oil pressure twice, so it is called a double-acting vane pump. The two suction zones and the two pressurized zones of the pump are radially symmetrical, and the hydraulic force acting on the rotor is radially balanced, so it is also called a balanced vane pump.
The instantaneous flow rate of a double-acting vane pump is pulsating and the pulsation rate is small when the number of vanes is a multiple of 4. For this reason, the number of blades of a double-acting vane pump is generally 12 or 16.
Classification of Rexroth vane pumps: Because of the history of vane pumps according to the different types of two types
a) Specifically refers to the sliding vane pump in the positive displacement pump.
2) Refers to the three pumps of the power pump (centrifugal pump, mixed-flow pump, axial flow pump) or other special pumps.
This type of pump product is generally not called a vane pump. However, as a monograph, vane pumps almost all refer to centrifugal pumps, mixed-flow pumps, axial flow pumps, etc.
|
More on that
|
The opening ceremony of the second phase of the Bosch Rexroth plant in Xi'an was a complete success
On November 11, 2020, the opening ceremony of the second phase of Bosch Rexroth (Xi'an) Electronic Drive and Control Co., Ltd. was grandly held. With the completion of the second phase of the project, the Xi'an plant will become the overall supplier of the group's global intelligent manufacturing and industrial automation solutions, and Bosch Rexroth will provide the best solutions for the Chinese market.
|
|
The principle and method of Rexroth hydraulic pump oil quantity adjustment
1. The principle of Rexroth hydraulic pump oil volume adjustment
Generally, in order to adapt to the specific requirements of the diesel engine under the load, the fuel injection pump must be able to adjust the maximum fuel supply to the zero oil supply range of the whole machine when the fuel supply is running.
|
|
Bosch Rexroth has launched Sino-Pack 2022
On March 4th, as a well-known intelligent packaging exhibition in Asia, China International Packaging Industry Exhibition Guangzhou was grandly opened. As the world's leading supplier of complete automation systems, Bosch Rexroth offers a high level of automation and electrical control and linear drive technology.
|
|
Features and applicability of Rexroth solenoid valves
peculiarity
1. Rexroth solenoid valve, solenoid valve and all stainless steel; For highly corrosive media, the diaphragm type must be selected. Neutral medium, it is also advisable to choose a solenoid valve with copper alloy as the housing material, otherwise, rust chips often fall off in the valve housing, especially when the action is infrequent. Ammonia valves ...
|
|
Rexroth variable piston pump displacement control mode
1. Guiding ideology:
1. The pressure depends on the load oil pump, and the output pressure is inversely proportional to the flow rate. In the state of electronic control, when the external load increases, the system pressure increases, when the system pressure increases, the pressure of the front pump oil flow and the rear pump oil flow into the rear pump increases, and the computer detects the ...
|
|
Rexroth and Magsmart jointly develop a solution for efficient hydrogen compression
Efficient hydrogen compression can halve the total cost of ownership for operators
More economical delivery helps to reduce the price of hydrogen refueling
Automatic seal replacement for easier maintenance
The container-based hydrogen compressor MAX Compression 2.0 is equipped with a digital hydraulic system from Bosch Rexroth ...
|
|
Rexroth expands linear robots to help factory automation
The expanded Bosch Rexroth Cartesian coordinate system subsystem opens up new areas of application
Predefined linear robots are suitable for a wide range of work areas and load ranges
ctrlX AUTOMATION is used as a shared automation platform
Optional pre-installed software for faster commissioning and programming ...
|
|
Rexroth hydraulic pump - how to use the piston pump
1. Preparation before starting: check the fastening of each component; Check the oil level of the oil tank, the height of the oil level is subject to the engraving line of the oil window on the oil tank, N46 in summer, N32 hydraulic oil in winter. High-pressure pumps and pumps above 140 should use the same type of anti-wear hydraulic oil. Check the pressure gauge range, liquid ...
|
|
Bosch Rexroth appeared at the 2020 Industry Fair
From September 15th to 19th, the 22nd China International Industry Fair was held as scheduled at the National Convention and Exhibition Center. Bosch Rexroth, a leading practitioner and supplier of Industry 4.0, presents 6.1 with the classical value stream of the factory of the future and the innovative automation platform ctrlXAUTOMATION with the theme of the future, using the present.
|
|
The pressure regulation step of the Rexroth pressure reducing valve
1. Close the gate valve before the pressure reducing valve, open the gate valve after the pressure reducing valve, and create a downstream low-pressure environment;
2. Rotate the adjusting screw counterclockwise to the upper position (relative to the low outlet pressure), and then close the gate valve after the pressure reducing valve;
3. Slowly open the gate valve in front of the pressure reducing valve ...
|
|
Precautions for the installation of Rexroth pressure reducing valves
1. When installing, the tap water pressure reducing valve should be installed vertically on the tap water pipeline.
2. The arrow on the tap water pressure reducing valve must be consistent with the arrow on the pipeline.
3. The position of the installation of the pressure reduction method must be greater than 4 meters from the valve outlet.
...
|
|
Rexroth's intelligent press-fit function kit is plug-and-play
The automotive industry expects more support from suppliers in quality assurance for assembly work. As a result, suppliers in the automotive industry are looking to automation partners to better meet this technology demand while delivering faster. Mechanical engineering companies need more applications in standard tasks ...
|
|
Rexroth's ACTIVE Cockpit interactive software solution has been upgraded
At a glance: 81% more widget space
Fast positioning with the new navigation concept
Efficient features like favorites, quick search, media management, and more
The Bosch Rexroth ACTIVE Cockpit interactive software solution is suitable for a wide range of applications. ...
|
|
Bosch Rexroth becomes a new partner of NEVONEX
· Bosch Rexroth Telematics Units (RCUs) help expand the digital ecosystem in agriculture
· The RCU can also be used as the basis for the manufacturer's own telematics solution
After partnering with Bosch Rexroth, NEVO, a manufacturer-independent provider of digital services ecosystem for agriculture ...
|
|
Rexroth A10VSO variable piston pump pressure flow adjustment steps
1. First, adjust the pressure adjusting screw of the relief valve to the loosest state, adjust the minimum flow limiter to the minimum state (the adjusting screw of the hydraulic cylinder in the upper part is adjusted to the loosest state), adjust the adjusting screw of the flow control valve to the tightest state, and connect a flowmeter in series after the relief valve;
2. Start-up fluid ...
|
|
Applicable power supply conditions for Rexroth solenoid valves
1) According to the type of power supply, AC and DC solenoid valves are selected respectively. In general, AC power is easily accessible;
2) AC220V.DC24V is preferred for voltage specifications;
3) The power supply voltage fluctuation is usually +%10%.-15% for AC, and about ±%10 for DC allowable ...
|
|
WAGO Rexroth has teamed up to create the ctrlX OS
Future-proof digitalization and automation technologies must be open, flexible, easily scalable, and secure at the same time. Whether it's mechanical and systems engineering, building and energy automation, the convergence of IT and OT applications is strongly supported and promoted by industry players. As the first system ...
|
|
How do Rexroth piston pumps supply oil?
1. Straight shaft swash plate Rexroth piston pump is divided into two types: pressure oil supply type and self-priming oil supply type. Most of the pressure oil supply hydraulic pumps use oil tanks with air pressure, and there are also hydraulic pumps with oil replenishment sub-pumps to provide pressure oil to the oil inlet of the hydraulic pump. The self-priming hydraulic pump has a strong self-priming capacity ...
|
|
Common failures of Rexroth vane pumps
1. Check whether the Rexroth vane pump shaft follows the motor rolling: if the motor rolls and the Rexroth vane pump shaft does not rotate, it may be a missing key on the Rexroth vane pump shaft or the key on the motor.
2. Check whether the rotation direction of Rexroth vane pump is correct: the steering is wrong, Rexroth ...
|
|
Rexroth's autonomous mobile robot wins the LogiMAT "Best Product" award
At LogiMAT 2022, an independent jury of scientists and journalists recognized Bosch Rexroth's autonomous mobile robot (AMR) ActiveShuttle as the "best product" in the category "Order picking, conveying, lifting and storage technology". As a ...
|
|
Contact
working hours
