Hollysys DCS - What are the characteristics of DCS?

(1) High reliability DCS is designed to be fault-tolerant, so that when a computer fails, it does not cause the system to lose other functions. In addition, because the tasks undertaken by the individual computers in the system are relatively simple, it is possible to adopt a specific structure and ...

Since the reform and opening up, China's economy has developed rapidly, and many enterprises have improved production efficiency by introducing foreign production equipment and DCS systems. However, with the growth of the use years, many foreign DCS systems and equipment have gradually aged and are not suitable for the current production needs, so they are localized.

The choice between a programmable logic controller (PLC) and a distributed control system (DCS) is a case-by-case analysis, as the requirements for the control system vary depending on the application. You can start from the following aspects! PLC and DCS PLC ...

On December 18, 2020, the "8th Member Congress and 2020 Zhejiang Enterprise Leaders Summit" hosted by Zhejiang Enterprise Confederation, Entrepreneur Association and Industrial Economics Federation (hereinafter referred to as the "Three Associations" of Zhejiang Province) was held in Hangzhou. At the conference, the top 100 in Zhejiang Province in 2020 were commended.

On November 13, 2022, Zhong'an United Coal Chemical Branch came with exciting news that the 20,000 tons/year butene-1 plant produced qualified butene-1 products at 22 o'clock on the same day, and the one-time start-up was successful. The control system of the device adopts the innovative technology product "OCS Industrial Optical Bus Control ...

(1) When the PLC and the host computer (or touch screen) form a monitoring system, there are many times when there are "manual", "automatic" and other control modes on the screen (generally when there is only one multiple). You can use the "MOV" command in the program. For example, when "manual" is selected, the constant 1 MO ...

(1) Select the appropriate PLC model and I/O points, and select the special function module when there are special function requirements. (2) Familiar with the selected PLC programming instructions and compilation software. (3) Carry out soft component planning, including internal relays, holding relays, data registers, ...

Merit: 1. High reliability: The DCS system has multiple redundancy, backup and recovery mechanisms, which can ensure the high reliability and stability of the system. 2. Sensitivity: The DCS system can be customized according to different industrial processes to meet different control requirements. 3. Efficiency: D...

In general, PLCs are extremely reliable devices with a very low failure rate. The probability of hardware damage such as the CPU of the PLC or software running errors is almost zero; If the PLC input point is not caused by strong current intrusion, it will hardly be damaged; The normally open point of the PLC output relay, if it is not a short circuit of the peripheral load ...

CNC machine tool PLC (programmable logic controller) has the following common faults in the operation process, and the following corresponding solutions are taken for the faults in the work engineering to make the equipment operate normally. 1. The power grid fluctuates too much, and the PLC does not work It is manifested as no output of the PLC. Check first ...

On September 20, 2022, Berlin time, the 13th Germany Berlin International Rail Transit Exhibition (InnoTrans 2022) opened at the Berlin International Exhibition Center in Germany. Following the 2018 exhibition, Hollysys once again appeared at the Berlin International Railway Exhibition (hereinafter referred to as the Berlin Exhibition) ...

1. DCS is a "distributed control system", while PLC (programmable controller) is just a control "device", which is the difference between the two. The system can realize the function and coordination of any equipment, and the PLC equipment only realizes the function of this unit. 2. In terms of networking, the DCS network is ...

1. The switching quantity is also called the logical quantity, which means that there are only two values, 0 or 1, ON or OFF. It is the most commonly used control, and controlling it is the advantage of PLC, and it is also the most basic application of PLC. The purpose of switching control is to follow the current input combination with the historical input according to the switching quantity.

1. Relay output circuit This type of output circuit form can be either DC or AC. The output circuit form of PLC relay allows the load to be generally below AC250V/50V, the load current can reach 2A, and the capacity can reach 80-100VA (voltage × current), so ...

On the morning of October 20, 2021, at the Epec Industrial Products Exhibition, Hollysys released a new 100% localized system - 'HOLLiAS MACS IC fully autonomous and controllable DCS system'. The system integrates the controller microkernel architecture independently developed by Lisi, embedded ...

At 15:05 on January 12, 2022, Datang Anhui Luoneng Power Generation Co., Ltd. (hereinafter referred to as Datang Luohe) successfully completed the full-load trial operation of Unit 5 after comprehensive upgrading, marking the smooth operation of Unit 5 of Datang Luohe Power Plant after the transformation. Hollysys HOLLiAS MACS IC completely ...

01. Power supply The DCS power supply system is mostly a "dual backup hot redundant power supply", and the prevention and control of power failures is mainly reflected in the inspection and daily maintenance. Generally speaking, as long as the unit is normal ...

3. Main anti-interference measures (1) Reasonable treatment of power supply to suppress the interference introduced by the power grid For grid disturbances introduced by the power supply, an isolation transformer with a shielded ratio of 1:1 can be installed to reduce the interference between the equipment and the ground.

On April 7, 2021, the "2021 China Software Industry Annual Conference" hosted by the China Software Industry Association was held in Beijing. With years of technology accumulation and outstanding strength, Hollysys Group won the title of "The Most Influential Enterprise in China's Software Industry in 2020", as well as the "...

1. The connection line is loose and the contact is poor When the run indicator of the PLC turns red, the position of the plug changes to green with a manual move, indicating that the plug is loose, and it is best to replace the new connecting wire, and the plug is frequently plugged and unplugged, which will also lead to poor contact. 2. Strong electrical interference (external)