Soft Touch/Rorobot Soft Jaw BML-3C12[H]/S Opening and closing frequency 6 times/second

Introduction: Rorobot BMC-2076D5/S 　　Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G. Soft-touch materials are divided into conventional and non-marking types, ...

Introduction: Soft-Touch/Rorobot Soft-Touch Module Slip Mounting Plate SMP-15 Features: According to the length of the slot, it is divided into SMP-13 / SMP-14 / SMP-15 / SMP-16 It can be used for the assembly between the soft beak module, the connection combination [CM] and the aluminum profile The installation angle of the soft beak module and the ...

Introduction: Rorobot Finger Module B8V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Use Screw Accessory Kit PK) and Simplify Tubing Arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: ...

Introduction: Rorobot B-21413, it can grasp the battery, can grasp the screw, can grasp the camera module, can grasp the rod, but also grasp the incense ash, it can be used very well for the outer diameter of 8±8 (mm) workpiece grasping, without changing the fixture on the premise, according to different kinds of workpiece to choose different ...

Introduction:Rorobot Robot Soft Gripper BMC-20005V, B-20005V/S can be used well for 0.18mm-3mm between small and light and thin special-shaped workpieces, even if it is close to the plane, it can also do pinching and grabbing, to ensure that the surface of the product is flawless. For light and small, high blanking accuracy requirements and ...

Introduction: Rorobot Finger Module A4V5, Features and Applicable Scenarios: The module is thinner, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot BMC-20603[H]/S Features: The fingertips are opened in the positive pressure state and clamped in the vacuum state, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by supporting the fingertip distance D. Soft-touch materials are divided into regular [H] and non-...

Introduction: Rorobot Compact Active Driver ACU2-B makes the drive simpler, plug-and-play, small and convenient, and the best cp for the awake desktop robotic arm Product parameters Rated power: 18W Operating voltage: 24V Output air pressure: -85—100kPa ...

Introduction: Rorobot FM-A5V5/LS1 Features: Product parameters Positive pressure stroke: 24.5mm Negative pressure stroke: 19mm Safe working air pressure: 120kPa Recommended load: 280g Tare weight: 90g We take the guest ...

Introduction: Soft Touch/Rorobot Finger Module A8V4, Features and Applicable Scenarios: Large clamping force, can be used in series (using screw accessory kit PK) and simplifies the arrangement of the trachea. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the workpiece width is generally greater than 50mm. Product Features ...

Introduction: Rorobot Flange Connection Module FCM-S01, Flange Connection Module [FCM] is a connection between the end of the robotic arm and the sliding mounting plate [SMP], which can be used with the quick-change module [QCM], which is divided into spring rod type (S) and fixed rod type (R). Features: Compliant with IS...

Introduction: Rorobot Finger Module FM-C6V2, Features and Applicable Scenarios: Independent Installation, Can be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixing Method: Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot Finger Module FM-A8V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Finger Spacing and Angle Adjustable, Fixation Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: SoftTouch/Rorobot Quick Change Module QCM-02, Quick Change Module [QCM] is used for automatic quick change of spare grippers. The quick-change module [QCM] is installed between the flange connection module [FCM] and the end of the robotic arm, and is divided into the robotic arm side (R-side, installed at the end of the robotic arm) and the gripper side (G-side, ...

Introduction: Soft-Touch/Rorobot Actuator LCH-U is a lightweight actuator designed for soft-touch grippers with both positive pressure and vacuum output, and can be used for both multi-channel and asynchronous drives Product parameters Enter the air supply 0.4—0.6MPa Flow rate> 200L/min Lose...

Introduction: Soft Touch/Rorobot Finger F-B8 Features: The finger material can be selected as regular type, reinforced type [H] and anti-static type [AS]. The reinforced grade [H] has a higher operating pressure range and a gripping force of up to 300% of the fingers of conventional grades. Defend...

Introduction: Rorobot soft jaw BMC-3A18 [HAS]/S, soft jaw material is divided into conventional type [H] and non-marking type [HAS] Features: The fingertips are open in the positive pressure state, and clamped in the negative pressure state, it is recommended to use it with a soft-touch air driver, and the fingertip distance of the clamping fingertip G and the external support fingertip distance is D...

Introduction: Rorobot Finger Module FM-B8V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixing Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot Finger Module A5V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Soft-Touch/Rorobot Slip Mounts SMP-3L Features: It is divided into different styles according to the shape and length of the groove It can be used for assembly between the finger module [FM] and the flange connection module [FCM]. The mounting angle and position of the finger module [FM] can be adjusted freely ...