Soft Touch/Rorobot Driver LCH-U Positive Pressure Flow Rate 165L/min

Introduction: The soft beak series products perfectly solve the grasping problem of the robot in the face of miniature and irregular products. The soft bionic beak allows for easy gripping of studs, rings, or capacitors that are difficult to grasp by suction cups and metal pneumatic grippers without damaging the surface. Small, soft ...

Introduction: Rorobot Finger Module C5V5, Features and Applicable Scenarios: The module is thinner, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot Finger Module A6V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing between the mounting modules is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Soft-Touch/Rorobot Soft-Touch Module Slip Mounting Plate SMP-14 　　Features: According to the length of the slot, it is divided into SMP-13 / SMP-14 / SMP-15 / SMP-16 It can be used for the assembly between the soft beak module, the connection combination [CM] and the aluminum profile The installation angle of the soft beak module and the ...

Introduction: Rorobot Finger Module C6V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle ...

Introduction: Rorobot Finger Module FM-B8V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixing Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: FlexTouch/Rorobot Passive Driver iPCU2 FlexTouch/Rorobot Passive Driver iPCU2 Features: Compact soft-touch gripper-specific controller. Small size, light weight, easy installation. It has 3 adjustable output air pressure ranges, and fully supports the ...

Introduction: Soft Touch/Rorobot Finger F-C3 Features: The finger material can be selected as regular type, reinforced type [H] and anti-static type [AS]. The reinforced grade [H] has a higher operating pressure range and a gripping force of up to 300% of the fingers of conventional grades. Defend...

Introduction: Soft Touch/Rorobot Finger F-B8 Features: The finger material can be selected as regular type, reinforced type [H] and anti-static type [AS]. The reinforced grade [H] has a higher operating pressure range and a gripping force of up to 300% of the fingers of conventional grades. Defend...

Rorobot Finger Module C3V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Using Screw Accessory Kit PK) and Simplifies Tracheal Arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: Peculiarity...

Introduction: Rorobot BML-3C12[H]/S Features: The fingertips are opened in the positive pressure state and clamped in the vacuum state, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by supporting the fingertip distance D. Soft-touch materials are divided into conventional type [H] and non-marking ...

Introduction: Rorobot Finger Module B6V4, Features and Applicable Scenarios: Large clamping force, can be used in series (using screw accessory kit PK) and simplifies the arrangement of the trachea. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: ...

Introduction: Rorobot Finger Module FM-B7V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Finger Spacing and Angle Adjustable, Fixing Method: Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot Soft Jaw BMC-4G64[HAS]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G. Soft-touch materials are divided into regular [H] and non-...

Introduction: Rorobot Soft Jaw BML-1G071010/S Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type and non-marking type ...

Introduction: Rorobot Finger Module FMA7-V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing ...

Introduction: Soft-Touch/Rorobot Slip Mounting Plate SMP-4S Features: It is divided into different styles according to the shape and length of the groove It can be used for assembly between the finger module [FM] and the flange connection module [FCM]. The mounting angle and position of the finger module [FM] can be adjusted freely ...

Introduction: Rorobot Finger Module B6V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot Finger Module C4V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot module B-4A30/M is a slender soft claw, suitable for jelly shells, test tubes, badminton, cylindrical, hollow columns and other fragile and fragile objects of non-destructive internal support handling and sorting, to ensure that the product will not be scratched, reduce the defect rate. When multiple soft jaws are connected in series, ...