FlexTouch/Rorobot Flange Connection Module FCM-S01

Introduction: Rorobot Finger Module B8V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot soft beak module BM series can be installed in the connection module [CM] or flange connection module [FCM]; The soft beak module comprises a soft beak and a matching fitting joint; The module assembly is supplied with a straight-through fitting fitting (PN-066) or a side-through fitting fitting (PN-007); Soft beak ...

Introduction: Rorobot Finger Module A4V5, Features and Applicable Scenarios: The module is thinner, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot Finger Module B4V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and ...

Introduction: Rorobot BMC-3C12[HAS]/S 　　Features: The fingertips are opened in the positive pressure state and clamped in the vacuum state, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by supporting the fingertip distance D. Soft-touch materials are divided into regular [H] and non-...

Introduction: Rorobot Robot Soft Grip BMC-3G20[H]/S, B-3G20[H]/S is a strong small soft gripper that can grasp relatively heavy workpieces outside. Clamping force (0-0.6N) and clamping range (3-13mm), the recommended load is 60g. Compensates for the higher negative impact of other three-finger soft claws in grabbing ...

Introduction: Rorobot Robot Soft Jaw FM-A6V3/LS1, Soft Finger LS1 has good versatility and wear-resistant. It is suitable for rough workpiece surfaces such as food, metal, and plastic parts. When gripping the workpiece, the damage caused to the workpiece by the soft finger itself can be minimized. We...

Introduction: Soft Touch/Rorobot Finger F-B3 Features: The finger material can be selected as regular type, reinforced type [H] and anti-static type [AS]. The reinforced grade [H] has a higher operating pressure range and a gripping force of up to 300% of the fingers of conventional grades. Defend...

Introduction: Rorobot BML-3A18[HAS]/S Features: The fingertips are open in the positive pressure state and clamped in the negative pressure state, and it is recommended to use the soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G and the external support fingertip distance D. Soft claw material ...

Introduction: Rorobot B-4H18[H]/S Features: The fingertips are open in the positive pressure state, clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by using the external support fingertip distance D. The soft claw material is divided into conventional type [H] and non-marking type [ ...

Introduction: Rorobot Robot BML-20005V, B-20005V/S can be used well for small, light and thin special-shaped workpieces between 0.18mm-3mm, even if it is close to the plane, it can also do pinching and grabbing, to ensure that the surface of the product is flawless. For light and small, high blanking accuracy requirements and ...

Introduction: Rorobot Finger Module B4V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Using Screw Accessory Kit PK) and Simplifies Tracheal Arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: ...

Introduction: Rorobot B-21413, it can grasp the battery, can grasp the screw, can grasp the camera module, can grasp the rod, but also grasp the incense ash, it can be used very well for the outer diameter of 8±8 (mm) workpiece grasping, without changing the fixture on the premise, according to different kinds of workpiece to choose different ...

Introduction: Rorobot Flange Connection Module FCM-R08 Features: It conforms to ISO 9409-1:2004 standard (i.e. GB/T 14468.1-2006/) and is suitable for most robot flanges on the market. The maximum load is recommended 20 kg Suitable for non-standard clamps ...

Introduction: Soft Touch/Rorobot Finger Module A6V4, Features and Applicable Scenarios: Large clamping force, can be used in series (using screw accessory kit PK) and simplifies the arrangement of the trachea. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the workpiece width is generally greater than 50mm. Product Features ...

Introduction: Rorobot Soft Jaw BMC-2G1624[HB]/S Features: Clamped in the vacuum state, the fingertip is opened in the positive pressure state, and can be directly driven by the vacuum In combination with a soft-touch air drive (positive and negative pressure switching drive), the clamping workpiece size can be increased Soft claws ...

Introduction: Rorobot Compact Active Driver ACU2-B makes the drive simpler, plug-and-play, small and convenient, and the best cp for the awake desktop robotic arm Product parameters Rated power: 18W Operating voltage: 24V Output air pressure: -85—100kPa ...

Introduction: Soft-Touch/Rorobot Skid Shift Mounting Plate SMP-5S Features: It is divided into different styles according to the shape and length of the groove It can be used for assembly between the finger module [FM] and the flange connection module [FCM]. The mounting angle and position of the finger module [FM] can be adjusted freely ...

Introduction: Rorobot Finger Module FM-B6V1, Features and Applicable Scenarios: Combination of two-finger modules, compact structure, small footprint. The spacing and installation angle are not adjustable, which is suitable for clamping tiny, thin and light workpieces. Features: Features and applicable scenarios: two-finger ...

Introduction: Rorobot Robot Soft Jaw BMC-1G071010[LPAS]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted for the distance G between the fingertip and the workpiece. Soft claw material ...