Rorobot BMC-20005V[PAS] Opening and closing frequency: 6 times/second

Introduction: Rorobot BMC-20006 Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G The soft claw material is divided into conventional type and non-marking type.

Introduction: iPCU 2 is available as a standard iPCU 2-SMN and a high-speed iPCU 2-HMN compact controller. Small size, light weight, easy installation. The high-speed type has a larger flow rate and faster response speed, and is suitable for high-speed handling conditions. ...

Introduction: Rorobot Finger Module FM-C4V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixation: Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot Robot BMC-4B32[HAS]/S Features: The fingertips are open in the positive pressure state, and the clamping is in the vacuum state, and it is recommended to use the soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertips G and the outer support fingertips D. Soft claws ...

Introduction: SoftTouch/Rorobot Quick Change Module QCM-02, Quick Change Module [QCM] is used for automatic quick change of spare grippers. The quick-change module [QCM] is installed between the flange connection module [FCM] and the end of the robotic arm, and is divided into the robotic arm side (R-side, installed at the end of the robotic arm) and the gripper side (G-side, ...

Introduction: The multi-finger opposite hand claw has a large grasping strength, can be grasped in both directions by standing and lying down, has strong adaptability, and can perfectly solve the problems of shaking and positioning deviation when grabbing hanging parts. The soft material and adjustable grip force eliminate scratches and damages on the surface of the product. Aluminium profile frame, ...

Introduction: Rorobot Soft Jaw BMC-20802 Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G The soft claw material is divided into conventional type and non-marking type.

Introduction: Rorobot Robot BML-20005V, B-20005V/S can be used well for small, light and thin special-shaped workpieces between 0.18mm-3mm, even if it is close to the plane, it can also do pinching and grabbing, to ensure that the surface of the product is flawless. For light and small, high blanking accuracy requirements and ...

Introduction: Rorobot Finger Module C6V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Using Screw Accessory Kit PK) and Simplifies Tracheal Arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: ...

Introduction: Rorobot Robot Soft Jaw BMC-1G071010[LPAS]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted for the distance G between the fingertip and the workpiece. Soft claw material ...

Introduction: Rorobot BML-3G20[H]/S Features: The fingertips are open in the positive pressure state and clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type [H] ...

Introduction: Rorobot flange connection module FCM-R02 conforms to ISO 9409-1:2004 standard (i.e. GB/T 14468.1-2006/), suitable for most robot flanges on the market. Features: Light weight, suitable for lightweight multi-joint robots, ...

Introduction: FlexTouch/Rorobot Passive Driver iPCU2 FlexTouch/Rorobot Passive Driver iPCU2 Features: Compact soft-touch gripper-specific controller. Small size, light weight, easy installation. It has 3 adjustable output air pressure ranges, and fully supports the ...

Introduction: Rorobot BMC-3G20[H]/S 　　Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G. Soft-touch materials are divided into conventional type [H] and non-marking ...

Introduction: Rorobot Finger Module B7V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction:Rorobot Robot BML-2G1211[HAS] Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G The soft claw material is divided into conventional type [H] ...

Introduction: Rorobot BMC-4H18[HAS]/S Features: The fingertips are open in the positive pressure state, clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by using the external support fingertip distance D. The soft claw material is divided into conventional type [H and no ...

Introduction: Rorobot BMC-20006 Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft jaw material is divided into conventional type, when the weight of the workpiece ...

Introduction: Rorobot Finger Module A4V5, Features and Applicable Scenarios: The module is thinner, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot Finger Module B3V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing between the mounting modules is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.