Steps to make an Epson robot I/O cable

Flip over the cover plate that sits on the base, cut the strip that holds the battery in place, and connect the new battery adapter to the battery plate. LS series manipulator screw lubricating oil addition process 1. Set the power supply of the controller to ON. Set the motor to ...

1. Poor or partial contact of the robot teach pendant (replacement of contact panel) 2. The robot teach pendant is not visible (repair or replace the internal motherboard or LCD screen) 3. Robot teach pendant is defective, vertical wire, vertical belt, blurred screen, broken screen, etc. (replace LCD screen) ...

Epson releases the C8-700, C8L-900 and C8XL-1400 robots with a 1.4-meter spacing and a maximum payload of 8Kg, all of which are designed to fit standard Clean/ESD and IP67 maintenance grade configurations. The body of this robot ...

1. After the industrial robot is immersed in water, it is necessary to immediately turn off the operation of the robot and remove the power supply of the robot, so that the robot is in a state of shutdown and power-off. ...

If possible, please transfer the robot with a trolley, etc., under the same conditions as at the time of delivery. Please adhere to the following requirements when unboxing the robot. Qualified operators are required to carry out transfer operations such as rope handling, crane lifting and forklift driving. If carried out by an unqualified operator ...

There are three different models in the Epson G series SCARA robots: G10-65, G10/20-85, and G20-A0, all of which have three different device forms: table top device, ceiling device, and sidewall device! Among them, G series robots can be divided into two categories: G10 and G20, which have different ...

Can it be used in cold climates? Today's mainstream industrial tablet PCs use touch screens including capacitive screens and resistive screens. However, since the beginning of winter, the temperature has begun to drop sharply, people are wearing more and more slowly, and there are some problems that need to be paid attention to in the use of industrial computers in winter. In nation-building ...

Set the action area in the following 3 ways: 1. Setting based on pulse size (full joint) 2. Mechanical stop-based settings (1st – 3rd joints) 3. Rectangle scale setting in the X,Y coordinate system (joint 1 - joint 2) ...

In recent years, industrial robots have played an increasingly important role in factories around the world. In the production of a diverse range of products, including electronic components and food, industrial robots take on the task of conveying, installing and packaging products. For many production enterprises, it has become a production stream.

Weight Note: The weight of the end of the fixture + workpiece must not exceed T3: 3kg / T6: 6kg. The T3 series Epson robot is designed to work with a load of no more than T3: 3kg / T6: 6kg. In addition, it is necessary to set a value that is appropriate for the load. If at the end of the fixture w...

Myth 1: Underestimating useful load and inertia The number one misconception of robot users in the application is that they underestimate the need for useful load and inertia. Usually this is due to the fact that the weight of the tool at the end of the robot arm is not included in the calculation of the load. Secondly the formation of this error ...

Since 1981, Epson industrial robots were born in response to the production needs of Seiko watch devices, whether it is the traditional G series four-axis robots, or LS and RS series SCARA robots, as well as the C series six-axis robots, plus the newly released folding arm N series robots, all inherit the Epson ...

Flip open the cover plate located at the base, cut off the ribbon that holds the battery in place, and connect the new battery connector to the battery plate. LS series manipulator screw lubricating oil addition steps 1. Set the power supply of the controller to ON. Set the motor to non...

Connect to the USB port of the mobile phone to import the program. The specific steps are: 1. Download and import the application package of the device to the mobile hard disk or USB flash drive, and then connect it to the USBA port of the projector. 2. The machine detects ...

1. Poor contact or partial failure of the robot teach pendant (replace the touch panel) 2. The robot teach pendant is not visible (repair or replace the internal motherboard or LCD screen) 3. The robot teach pendant appears bad, vertical wires, vertical belts, ...

The industrial robot loading and unloading station is composed of loading and unloading robots, CNC machine tools, PLC control cabinets, conveyor lines, etc. (1) Loading and unloading industrial robots Loading and unloading industrial robots include: industrial robots, control cabinets, teaching devices and end actuators. Industrial robots and end actuators ...

1. Power cord: divided into internal filling and external filling. External filling lines are available for bottom and high current filling. The end of the wire is located at the front of the ramp and is fixed with the left hand, and it is continuously fed into the molten pool for welding. There is almost no gap between males. Its advantages include high current, small aperture ...

1. Number of robot axes. The number of axes of the robot affects the degree of freedom, if it is for a brief straight to go occasion, for example, a belt line from one side to the other, choose a simple four-axis robot; If the robot does not have much room to move, but the demand machine ...

1. What are the definitions and characteristics of industrial robots? Definition: A robot is a robot with multiple degrees of freedom in three-dimensional space, which can achieve a variety of anthropomorphic actions and functions Features: Programmable, Anthropomorphic, General, Electromechanical ...

1. Establish communication with the robot: through the EPSON RC+ software, click on the settings to communicate between the computer and the controller, and complete the communication between the PC and the robot. 2. Translation ...