First, the abnormal fault of the control pass
The abnormal fault of the control channel is usually caused by the optical fiber communication between the sub-PWM board and the power unit board, which is generally caused by the following situations:
1. Poor contact of the optical fiber connection part or falling off of the optical fiber head;
2. Ash accumulation inside the optical fiber signal transmitter/receiver;
3. Optical fiber breakage;
4. Optical fiber communication control vibration damage;
In the case of an optical fiber failure, it is first necessary to determine whether the power unit is faulty or the controller side is faulty, and the optical fiber can be adjusted by the method. The optical fiber corresponding to any power unit of the same phase on the optical fiber board in the controller is reversed with the optical fiber that reports the fault, and if the optical fiber fault located by the power-on monitoring interface is still in the original position, it means that the optical fiber board is damaged, on the contrary, the optical fiber fault displayed by the monitoring interface has been replaced, then it means that the power unit is faulty, and the faulty power unit can be considered to be replaced or repaired at this time.
2. Causes and solutions of IGBT overcurrent faults
IGBT is the most critical power device in high-voltage inverter, and as a high-power composite device, IGBT may be locked and damaged during overcurrent. In order to improve the reliability of the system charge, some measures have been taken to prevent damage due to overcurrent. There are several common causes of IGBT overcurrent faults:
1. The output of the inverter is short-circuited;
2. The IGBT in the power unit is broken down;
3. The drive detection circuit is damaged
4. The detection circuit is interfered with;
The detection method is to find the corresponding module according to the fault location displayed in the monitoring interface, disassemble and check whether the IGBT is damaged, and the method of judgment is to find the positive pole v+ and negative pole v- of the DC bus inside the power unit, connect the black gauge of the multimeter to v+, and the red gauge pen is connected to U, V respectively, with the second machine tube file, the value of about 0.4V should be displayed, and the inverted phase shows infinity;
3. Causes and solutions of overvoltage faults
The reason for overvoltage is generally the overvoltage from the input side of the power supply, and the passive power grid voltage is within -10%-+10% of the rated voltage under normal circumstances, but under special conditions. The voltage of the sub-DC bus rises with the power supply voltage, so when the voltage rises to the protection value, the inverter will trip due to overvoltage protection. In order to enter and exempt the input side overvoltage, the tap of the transformer can be changed for adjustment, this method is only suitable for the situation that the sub-field voltage has been high, and the absorption device can also be considered on the power input side to reduce the overvoltage factor on the input side of the inverter.
|
More on that
|
Megmeet inverter - the selection principle and precautions of the inverter
1. Select the inverter according to the load characteristics
A: Fans and pumps are the most common loads: the requirements for the inverter are the simplest, as long as the inverter capacity is equal to the capacity of the motor (air compressors, deep water pumps, sediment pumps, and fast-changing music fountains need to increase their capacity).
...
|
|
Megmeet drives – the replacement steps for high-voltage drive power units
1) Shut down, so that the inverter out of the operating state;
2) Cut off the high-voltage power supply and push out the high-voltage cabinet trolley (when there is a bypass cabinet. The inverter can be isolated by the disconnecting switch of the bypass cabinet), the local or remote high-voltage disconnect switch can be locked, and the high-voltage cabinet grounding switch can be grounded;
3) Hit ...
|
|
Megmeet inverter mv600 alarm code ENOC2
1. If there is a sharp acceleration or deceleration, please extend the acceleration and deceleration time.
2. Avoid rapid increase in load.
3. Check whether there is a short circuit in the UVW of the motor terminal.
4. The module is damaged, and the drive circuit is damaged, resulting in an overcurrent alarm.
...
|
|
Megmeet drives – what are the components of a drive?
The inverter is composed of a main circuit, a rectifier, a flat wave circuit, and an inverter.
1) Main circuit:
The main circuit is the power conversion part that provides voltage regulation and frequency regulation power supply for the asynchronous motor, and the main circuit of the inverter can be roughly divided into two categories: the voltage type is the DC ...
|
|
Megmeet inverters – what do you need to pay attention to when choosing the power of the inverter?
The system efficiency is equal to the product of the efficiency of the inverter and the efficiency of the motor, and the system efficiency is higher only when both are working at higher efficiency. From the perspective of efficiency, the following points should be paid attention to when selecting the power of the inverter:
1) Inverter power value and motor power ...
|
|
Megmeet PLC - Comparison of the advantages of PLC and DDC in building automation systems
1. Application field: The initial design goal of PLC is only to replace complex relay circuits, and DDC is originally only used in industrial automation instruments: PLC emphasizes versatility, DDC emphasizes specificity: PLC is used in the field of industrial control, and DDC is used in professional building systems.
2. Structural differences ...
|
|
Megmeet PLC – the three programming languages of PLC
1. The ladder diagram language is the most commonly used programming language in PLC programming. The CPU reads physical input into a memory table, often referred to as an "input table". The form is evaluated for use in the procedure. Different platforms, using different types of registers; In each scan cycle, follow from left to right, ...
|
|
Megmeet PLC - What places should be avoided when installing PLC control?
(1) The ambient temperature exceeds the range of 0-50 °C;
(2) The relative humidity exceeds 85% or there is dew condensation (caused by sudden temperature changes or other factors);
(3) direct sunlight;
(4) There are corrosive and flammable gases, such as hydrogen chloride, ...
|
|
Megmeet PLC – the maintenance steps of the PLC control cabinet
1. Data backup
When carrying out maintenance, we must cut off the power, data backup between power outages is an important link, for the data that needs to be archived for a long time, you can back up the historical trend data to the mobile hard disk, and then turn off the Windows-based operating system (Note...
|
|
The principle of Megmeet plasma cutting and its characteristics
5) PLASMA
The principle of plasma cutting is: arc discharge between the base metal (including the nozzle in the cutting torch) and the electric in the cutting torch, and use the discharge heat energy to make the compressed gas produce a high-temperature and high-speed plasma arc to fuse the cutting method of the base metal. The small hole of the nozzle ...
|
|
Megmeet inverter - the speed regulation method of high-voltage inverter
1. Hydraulic coupling method. That is, a hydraulic coupling device is inserted between the motor and the load in series, and the size of the coupling force between the motor and the load is adjusted by the height of the liquid level, so as to realize the speed adjustment of the load;
2. Cascade speed regulation. Tandem speed regulation must use a wound asynchronous motor, and the rotor ...
|
|
Megmeet welding machines – the main application area of resistance welding
(1) Spot welding: The weldment is pressed between the two cylindrical electrodes, heated by electricity, so that the weldment melts at the contact to form a nugget, and then the power is cut off, and it solidifies and crystallizes under pressure to form a dense solder joint.
Spot welding is suitable for welding thin plates (laps) and steel bars below 4 mm.
|
|
Megmeet welding machine - the working principle of the spot welding machine and its advantages and disadvantages are introduced
Safety operation procedures for spot welding machines:
1. Before operation, the oil stain of the upper and lower electrodes should be removed. After power-on, the body shell should be free of leakage.
2. Before starting, the steering switch of the control line and the small switch of welding current should be connected, the number of poles should be adjusted, and then the water source and gas source should be connected.
|
|
Common faults and solutions of Megmeet PLC
1. Do not execute the program: The input check is identified by the input LED indicator or the input monitor composed of a writer. When the input LED is not lit, it can be preliminarily determined that the external input system is faulty, and then check with the multimeter.
If the output voltage is not normal, it can be determined that ...
|
|
Megmeet PLC - an introduction to the classification of PLC
There are many types of PLC products, and their specifications and performance also vary. PLCs are usually classified according to their different structural forms, differences in functions, and the number of I/O points.
2.1 Classification by structural form
According to the structural form of PLC, PLC can be divided into whole ...
|
|
Megmeet PLC – the application of PLC
Open-loop control
Open-loop control of switching quantity is the most basic control function of PLC. The instruction system of PLC has powerful logic operation ability, and it is easy to realize various logic control methods such as timing, counting, and sequential (stepping). Most PLCs are used to replace traditional relay contactors...
|
|
Hollysys' nationally produced SCADA system was the first to be put into application in the refined oil pipeline network of National Petroleum Pipeline Network Group Co., Ltd
Preface:
Energy security is an overall and strategic issue related to the country's economic and social development, and is crucial to the country's prosperity and development, the improvement of people's lives, and the long-term peace and stability of society. For the first time, the 14th Five-Year Plan and the Outline of the Long-Range Objectives Through 2035 include "comprehensive energy production capacity" in the ...
|
|
Megmeet Welders – What are the commonly used types of welders?
1. The main welding machines used in industrial and mining enterprises are: AC arc welding machine, DC electric welding machine, argon arc welding machine, carbon dioxide maintenance welding machine, butt welding machine, spot welding machine, submerged arc welding machine, high-frequency welding machine, bright butt welding machine, pressure welding machine, butt welding machine and laser welding machine.
Communication welders and DC welders should ...
|
|
Megmeet PLC – The importance of PLC industrial gateways
1. Realize remote control of industrial field equipment;
2. The PLC industrial gateway realizes remote upgrade of equipment firmware, downloads the program, and can flexibly access various equipment management platforms;
3. Realize remote control of industrial site touch screen and remote mapping of configuration screens;
4. PLC industry ...
|
|
Megmeet PLC - PLC's inverter control motor forward and reverse wiring diagram
1. After connecting the wires according to the wiring diagram, start the power supply and prepare to set the parameters of the inverter.
2. Press the "MODE" button to enter the parameter setting mode, and set the Pr.79 to "2": external operation mode, the start signal is input by the external terminal (STF, STR), and the speed adjustment is carried out by the external terminal.
|
|
Contact
working hours
