Omron's new product [Miniature Connector Terminal Block XW2K Series] was officially released

Using an Omron electronic thermometer, which is displayed digitally and compared with a conventional thermometer, there is a small chance of error, generally no more than 0.1 degrees, so there is little need to worry about inaccuracies. Every time you use it, it's also very simple, just press the power switch ...

The 5th China International Import Expo (hereinafter referred to as the "Expo") will officially kick off on November 5. As a global expert in digital transformation in the field of automation, Omron will attend the appointment for the fifth time and bring new digital intelligence technologies and solutions to show its continuous focus on social development.

Omron's recommended product models today: K8DS is a triple opposite missing sequential appliance The inverse lacks sequential electrical appliances Three-phase voltage + inverted phase lack sequential electrical appliances Three-phase unbalanced + inverted lack of sequential electrical appliances Three-phase undervoltage + inverted inverted missing sequential electric Three-phase voltage + three-phase ...

(1) When measuring voltage, it is necessary to use a digital voltmeter or a universal meter with an accuracy of 1%. (2) The power supply rack and CPU motherboard can only be removed when the main power supply is cut off; (3) Before the RAM module is removed from the CPU or plugged into the CPU, the power supply of the PC should be disconnected.

Process introduction The sewing and cutting line is mainly used for sewing and cutting shirt collars, sleeves and pockets, and the equipment is divided into the following 4 parts: 1. Discharging part: used for the initial positioning of sewing materials, the laser projection position is controlled by the motor, and the materials are manually placed on the platform.

First, the contact point is loosened and cracked The contact point is the electrical contact part of the Omron relay to convert the load, and the contact point of some products is matched with each other by riveting pressure, and the key disadvantage is that the contact point is loose, the contact point is cracked or the error of the standard part is too large. This will jeopardize the relay ...

After adding the I/O module, you need to set it in the CX-PROGRAMMER program. Find the IO table and unit settings, double-click to find the mainframe [0000], dot + sign, and then double-click 00 (if not set), 00 represents the module number closest to the CPU.

Process introduction In the traditional die-cutting process, because the cutter cannot cut the material completely, the connecting frame will be left, which increases the cost of the material. In addition, the service life of the die-cutting knife is 1 million times, such as long-term continuous operation, it needs to be replaced and maintained in time, and the maintenance and debugging time is also very long.

Recently, the 2022 P&G Electrical Automation Seminar held by Procter & Gamble (China) Co., Ltd. (hereinafter referred to as "P&G") was held in Guangzhou. Omron Automation (China) Co., Ltd. (hereinafter referred to as "Omron") was invited to attend the meeting and worked with the engineering, manufacturing, R&D and other departments of P&G factories on behalf of the ...

1. Before connecting, determine the voltage required for the proximity switch, and if it is a 3-wire system, determine whether it is PNP type or NPN type. The proximity switch is divided into 2-wire, 3-wire and 4-wire systems. 2. When the wire system proximity switch is connected with the relay, it is in series form. i.e. the relay is connected to the proximity switch ...

For the problem that the Omron photoelectric switch only lights green, it may be because a component on the circuit board is faulty or damaged, or because of the poor connection of a component on the circuit board. So, to deal with this, the first thing to do is to see if the components on the board are ...

One. Omron switch in daily use, basically need to be used every day, when using Omron switch, you need to pay attention not to wet hand operation, to avoid electric shock accidents, and secondly, if the water vapor once invaded the inside of the switch line, it will cause internal damage to the switch, than ...

Recently, Omron Automation (China) Co., Ltd. (hereinafter referred to as "Omron") and BYD Co., Ltd. (hereinafter referred to as "BYD") successfully held a technical exchange meeting in Shenzhen. Omron industry and technical experts, BYD automobile, light rail, new energy, electronics ...

The first 1. First of all, we open the CX-P software, set the PLC model, enter the programming section, and prepare for programming. 2. Usually when we program, we are used to entering LD instruction programming, when we need to input the rising edge, we need to enter @LD0.00, you can. 3. Down...

Process introduction Since the implementation of the [plastic restriction order] in 2007, plastic packaging has been greatly restricted. Subsequently, all kinds of metal cans represented by beer cans, tea cans, and oil cans are increasing, and metal packaging has begun to usher in a period of rapid development. Metal cans are divided into ...

1. The IP address of the computer is automatically obtained. 2. The computer is directly connected to the PLC network port. 3. Open the DirectEthernetUtility software. Software Setup Start - > All Programs - > OMRON - >Communications Middleware Utilities - > DirectE...

1. Overhaul the power supply. It is possible to detect whether the voltage variation range is within the permissible ± 10% at the power terminal. 2. Working environment. Focus on checking whether the temperature, humidity, vibration, dust, interference, etc. meet the standard working environment. 3. Power supply for input and output. Available in the corresponding ...

How it works Add a certain voltage at both ends of the coil, a certain current will flow through the coil, thus producing an electromagnetic effect, and the armature will overcome the tensile force of the return spring under the action of electromagnetic force attraction and attract to the core, thereby driving the dynamic contact and static contact (normally open contact) of the armature ...

Hoffman Estates, Illinois, March 24, 2020 – Manufacturers in the automotive industry are trying to capitalize on the current trend toward electric vehicles and low fuel consumption by building lightweight vehicles and favoring aluminum over iron. With the inclusion of both iron and aluminum ...

1. Fault phenomenon: After powering on, the power supply does not respond. 2. Cause of failure: (1) The input power supply voltage is insufficient and does not reach the specified range. (2) The input power supply voltage is instantaneously impulsed, resulting in damage to the input components (such as fuses, rectifications, etc.) as shown in the figure: ...