Rittal takes you through the efficient and accurate configuration of your enclosure system

At the China International Information and Communication Exhibition (PT Exhibition) in Beijing, Rittal is showcasing its innovative "edge data center" solutions. In an era of increasing demand for high-speed processing and maximum flexibility, small, flexible edge data centers are digitizing enterprises in a steady stream of ...

1. DC resistance: 20°C, 0.4mm copper wire, less than or equal to 148Ω/km, 0.5mm copper wire, less than or equal to 95Ω/km. 2. Insulation electrical strength: 1min 1kv between conductors does not break down, conductors and shields 1min 3kv do not break down 3. Insulation resistance: each core and the rest of the core ...

1. Make sure that all equipment in the electrical control cabinet is well grounded, and use short and thick grounding wires to connect to the common grounding point or grounding busbar. Any control equipment connected to the inverter should be co-grounded with it, and likewise ground with short and thick wires; 2. Flat conductors are used, e.g. ...

With the continuous promotion of the dual carbon policy, the development of new clean energy such as wind power has been making great progress. China and United States are among the world's largest growing countries for wind energy equipment. Wind turbines typically need to operate reliably for more than 20 years to deliver electricity to people. To this end ...

1. a rack Rack: Installed in a standard cabinet, it is a functional server, so the standard cabinet is also called a "19-inch" rack. Rack is a more professional academic term, and most of the current policy documents mention "rack", and clarify the indicators such as single rack power and average shelf rate ...

What are the principles for drawing and reading the schematic diagram of electrical control circuits? Answer: A. The schematic diagram is generally divided into power supply circuit, main circuit, control circuit, signal circuit and lighting circuit. B. In the schematic diagram, the position of the contacts of each electrical appliance is according to the ...

1. Judgment and treatment of sudden tripping fault of high-voltage switchgear during operation 1) Fault phenomenon: The cause of this failure is the protection action. The high-voltage cabinet is equipped with protection against overcurrent, quick cut-off, gas and temperature. 2) Judgment method: judging the cause of the fault can be based on the relay off, remote ...

1. A01 system message: open the cabinet door Rittal air conditioner Cause: the position of the door opening and closing is incorrect; 2. A02 system message: the temperature in the cabinet is too high: the refrigeration capacity is too low or small; 3. A03 System Message: Filter Monitoring Cause: Dirty Filter Diagnosis ...

21. What does the workplace have to meet for high-voltage electrical appliances? Answer: A. Rated voltage, B. Maximum working voltage, C. Rated current, D. Rated short-circuit interrupting current, E. Short-time withstand current and peak withstand current. 22. What are the basic requirements for a high-voltage circuit breaker? Answer: A work ...

First, set posts and responsibilities. The power department of distribution box equipment should number, register, file, hierarchical management, clear responsibilities, and regularly carry out technical inspection and maintenance of the distribution box.

1. Maintenance content (1) Check the heat dissipation of the controller It is strictly forbidden to cover the controller with plastic or other materials; Leave enough space behind and on the sides of the controller (> 120mm); It is strictly forbidden to position the controller close to the heat source; It is strictly forbidden to put sundries on the top of the controller; Avoid over-the-top ...

Closing faults can be divided into electrical faults and mechanical faults. There are two types of closing methods: manual and electric. Failure to close manually is generally a mechanical failure. Manual can be closed, electric can not close is an electrical fault. 1. Protection action: The protection action has been analyzed in front to trip the switch. ...

The Rittal compact AE cabinet with its new internal expansion rails –Supplementary internal expansion for machining – Can be done in a time-saving manner in the side, bottom and top cover areas Installation – Two rows of adjustable TS 8 system holes for installation capacity Outer space...

1. The power cords of the two cabinets are connected to the power socket at the rear of the cabinet. 2. The RS232 interface of the two cabinets is connected together with a communication cable. 3. Lock the door of the main cabinet, and turn on the power from the cabinet and the main cabinet in turn. ...

Rittal has an economical air conditioner on the market, and the Rittal RBT cooling unit – is your most economical choice! If a limited budget makes you more interested in the cost Extremely sensitive, then RBT is the ideal choice for you Choose. Produced through large-scale assembly lines, as well as cold But the unit itself is excellent ...

Server cabinets have requirements in terms of depth, height, and load-bearing capacity. There are three heights of 2.0 meters, 1.8 meters and 1.6 meters; The width is 800mm, 700mm or 600mm; There are three depths: 700mm, 800mm and 900mm. Can be configured: special fixed pallet, special ...

1. The Rittal air conditioner does not start when it is turned on, and the A17 is faulty. Check that the power supply voltage is 220V, normal; Detect that the battery voltage of the remote control is 3V, which is normal; Measure the fuse resistance value of the air conditioner compressor with a multimeter as infinity, which is normal. 2. The Rittal air conditioner does not start when it is turned on, and the display is not started.

1. What is TT, IN, IT system? A: The TT method refers to a protection system that directly grounds the metal shell of electrical equipment, which is called a protective grounding system, also known as a TT system. The TN method is a protection system that connects the metal shell of the electrical equipment with the working neutral line, called ...

How to promote the further development of smart factories and smart production? The Rittal Hager plant in Germany illustrates how the smart factory can be accelerated with a digital twin in manufacturing! 　　As one of the world's modern cabinet production bases, the Hager plant has a production capacity of 24,000 square meters.

1. The circuit breaker cannot be closed Causes: 1. The undervoltage coil does not work (the voltage is normal). Solution: Replace the undervoltage coil. 2. Press the closing button, and the closing coil will not work when it is powered up. Solution: Replace the undervoltage coil. 3. Cooperation...