Soft Touch/Rorobot Finger F-B6 Fingertip Travel 53mm

Introduction: Rorobot BML-2076D5/S Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type and non-marking type, ...

Introduction: Rorobot Finger Module FMA7-V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing ...

Introduction: Rorobot Finger Module B8V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot soft jaw BMC-3A18 [HAS]/S, soft jaw material is divided into conventional type [H] and non-marking type [HAS] Features: The fingertips are open in the positive pressure state, and clamped in the negative pressure state, it is recommended to use it with a soft-touch air driver, and the fingertip distance of the clamping fingertip G and the external support fingertip distance is D...

Introduction: Soft Touch/Rorobot Finger F-C6 Features: The finger material can be selected as regular type, reinforced type [H] and anti-static type [AS]. The reinforced grade [H] has a higher operating pressure range and a gripping force of up to 300% of the fingers of conventional grades. Defend...

Introduction: Soft Touch/Rorobot Finger Module FE-A3V1, Features and Applicable Scenarios: Combination of two-finger modules, compact structure, small footprint. The spacing and installation angle are not adjustable, and it is suitable for clamping small, light and thin workpieces. Features: Features and applicable scenarios: ...

Introduction: Rorobot BMC-3B14/S 　　Features: The fingertips are open in the positive pressure state, and clamped in the negative pressure state, it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted with the distance between the fingertips of the inner support and the fingertips. The soft claw material is divided into conventional type and non-marking type, when ...

Introduction: Rorobot BMC-2076D5[P1/S Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type and non-marking ...

Introduction: Soft-Touch/Rorobot Soft-Touch Module Slip Mounting Plate SMP-15 Features: According to the length of the slot, it is divided into SMP-13 / SMP-14 / SMP-15 / SMP-16 It can be used for the assembly between the soft beak module, the connection combination [CM] and the aluminum profile The installation angle of the soft beak module and the ...

Introduction: Rorobot Robot Soft Jaw BMC-1G071010[LP]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted for the distance G between the fingertip and the workpiece. The soft claw material is divided into ...

Introduction: Rorobot Finger Module FM-B7V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Finger Spacing and Angle Adjustable, Fixing Method: Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot FM-A5V5/LS1 Product parameters Positive pressure stroke: 24.5mm Negative pressure stroke: 19mm Safe working air pressure: 120kPa Recommended load: 280g Tare weight: 90g Our customer-centric service ...

Introduction: Rorobot Finger Module B5V4, Features and Applicable Scenarios: Large clamping force, can be used in series (using screw accessory package PK) and simplifies the trachea arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: ...

Introduction: Rorobot ACU-MMN Active Driver, ACU-MMN Active Driver--Standard, Mobile Soft Touch Gripper Special Controller, Output Air Pressure -70-120kPa, Manually Adjust the Clamping Force by Knob. Built-in drive air source and battery, can be fully charged without external power supply ...

Introduction: Rorobot Finger Module FM-B6V1, Features and Applicable Scenarios: Combination of two-finger modules, compact structure, small footprint. The spacing and installation angle are not adjustable, which is suitable for clamping tiny, thin and light workpieces. Features: Features and applicable scenarios: two-finger ...

Introduction: Soft Touch/Rorobot Finger Module FMA5-V3 Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing ...

Introduction: Rorobot Soft Beak B-3B14 Features: Replaceable flexible chucks The fingertips are open in the positive pressure state, clamped in the negative pressure state, and the fingertips are adjustable from G It can be used as a clamp or external support Recommended for use with soft-touch actuators Product References ...

Introduction: Rorobot Flange Connection Module FCM-R02 Features: It conforms to the ISO9409-1:2004 standard (i.e., the national standard GB/T 14468.1-2006/), and is suitable for most robot flanges on the market. Lightweight for lightweight articulated machines ...

Introduction: Soft-Touch/Rorobot Slip Mounting Plate SMP-2S Features: It is divided into different styles according to the shape and length of the groove It can be used for assembly between the finger module [FM] and the flange connection module [FCM]. The mounting angle and position of the finger module [FM] can be adjusted freely ...

Introduction: Soft-Touch/Rorobot Slip Mounts SMP-3L Features: It is divided into different styles according to the shape and length of the groove It can be used for assembly between the finger module [FM] and the flange connection module [FCM]. The mounting angle and position of the finger module [FM] can be adjusted freely ...