Soft Touch/Rorobot Finger F-C6 Finger Width: 12mm

Introduction: Rorobot Robot BML-1G071010[LP]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted for the distance G between the fingertip and the workpiece. The soft claw material is divided into ...

Introduction: Rorobot BMC-2G1624 [HBAS]/S Features: Clamped in the vacuum state, the fingertip is opened in the positive pressure state, and can be directly driven by the vacuum In combination with a soft-touch air drive (positive and negative pressure switching drive), the clamping workpiece size can be increased Soft...

Introduction: Rorobot Finger Module C6V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle ...

Introduction: Rorobot Finger Module B3V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing between the mounting modules is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot BML-3G20[HAS]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G. Soft-touch materials are divided into regular [H] and non-...

Introduction: SoftTouch/Rorobot Connection Module CM-S04 Features: A full range of soft beak modules can be installed at the end Can be mounted on the Flexible Series Slip Mounting Plate [SMP] page.50 Elastic cushioning structure design, especially suitable for multi-layer elastic soft fabric products...

Introduction: Rorobot B-20606/S Features: The fingertips are opened in the positive pressure state and clamped in the vacuum state, and it is recommended to use it with a soft-touch air driver, and the fingertip distance G is supported to use the working air pressure adjustment. Soft-touch materials are divided into conventional type [H] and non-marking type, ...

Introduction: Rorobot B-4B40/S Features: The fingertip is open in the positive pressure state, clamped in the vacuum state, it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G and the external support finger distance D. Soft-touch materials are divided into conventional ...

Introduction: Soft-Touch/Rorobot Soft-Touch Module Slip Mounting Plate SMP-15 Features: According to the length of the slot, it is divided into SMP-13 / SMP-14 / SMP-15 / SMP-16 It can be used for the assembly between the soft beak module, the connection combination [CM] and the aluminum profile The installation angle of the soft beak module and the ...

Introduction: iPCU 2 is available as a standard iPCU 2-SMN and a high-speed iPCU 2-HMN compact controller. Small size, light weight, easy installation. The high-speed type has a larger flow rate and faster response speed, and is suitable for high-speed handling conditions. ...

Introduction: Rorobot Finger Module FM-C3V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixation Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot Finger Module FM-A8V1, Features and Applicable Scenarios: Combination of Two-Finger Module, Compact Structure, Small Footprint. The spacing and installation angle are not adjustable, which is suitable for clamping tiny, thin and light workpieces. Features: Features and applicable scenarios: two-finger ...

Introduction: Soft Touch/Rorobot Finger Module FM-A3V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Finger Spacing and Angle Adjustable, Fixing Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) . ...

Introduction: Rorobot BML-3C12[H]/S Features: The fingertips are opened in the positive pressure state and clamped in the vacuum state, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by supporting the fingertip distance D. Soft-touch materials are divided into conventional type [H] and non-marking ...

Introduction: Rorobot Robot Soft Grip BMC-3G20[H]/S, B-3G20[H]/S is a strong small soft gripper that can grasp relatively heavy workpieces outside. Clamping force (0-0.6N) and clamping range (3-13mm), the recommended load is 60g. Compensates for the higher negative impact of other three-finger soft claws in grabbing ...

Introduction: Soft Touch/Rorobot Finger Module B3V4, Features and Applicable Scenarios: Large clamping force, can be used in series (using screw accessory kit PK) and simplifies the trachea arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the workpiece width is generally greater than 50mm. Product Features ...

Introduction: Rorobot BMC-20006 Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G The soft claw material is divided into conventional type and non-marking type.

Introduction: Soft Touch/Rorobot Finger Module A6V4, Features and Applicable Scenarios: Large clamping force, can be used in series (using screw accessory kit PK) and simplifies the arrangement of the trachea. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the workpiece width is generally greater than 50mm. Product Features ...

Introduction: FlexTouch/Rorobot Passive Driver iPCU2 FlexTouch/Rorobot Passive Driver iPCU2 Features: Compact soft-touch gripper-specific controller. Small size, light weight, easy installation. It has 3 adjustable output air pressure ranges, and fully supports the ...

Introduction:Rorobot BML-2G1211[H] Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G The soft claw material is divided into conventional type [H] and ...