Rorobot B-3B14 weight 6.1g

Introduction: Rorobot Finger Module FMA4-V3, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixing Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot Finger Module B4V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Using Screw Accessory Kit PK) and Simplifies Tracheal Arrangement. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: ...

Introduction: Rorobot Robot Soft Grip BMC-3G20[H]/S, B-3G20[H]/S is a strong small soft gripper that can grasp relatively heavy workpieces outside. Clamping force (0-0.6N) and clamping range (3-13mm), the recommended load is 60g. Compensates for the higher negative impact of other three-finger soft claws in grabbing ...

Introduction: Rorobot BMC-4H18[H]/S Features: The fingertips are open in the positive pressure state, clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by using the external support fingertip distance D. The soft claw material is divided into conventional type [H and non-marking ...

Introduction: Rorobot Finger Module C5V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and ...

Introduction: Rorobot Robot Soft Jaw FM-A6V3/LS1, Soft Finger LS1 has good versatility and wear-resistant. It is suitable for rough workpiece surfaces such as food, metal, and plastic parts. When gripping the workpiece, the damage caused to the workpiece by the soft finger itself can be minimized. We...

Introduction: Rorobot Soft Beak B-20006 Features: Replaceable flexible chucks The fingertips are open in the positive pressure state, clamped in the negative pressure state, and the fingertips are adjustable from G It can be used as a clamp or external support Recommended for use with soft-touch actuators Products...

Introduction: Rorobot Finger Module A3V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping small, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot Finger Module C5V5, Features and Applicable Scenarios: The module is thinner, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot flange connection module FCM-R02 conforms to ISO 9409-1:2004 standard (i.e. GB/T 14468.1-2006/), suitable for most robot flanges on the market. Features: Light weight, suitable for lightweight multi-joint robots, ...

Introduction: Rorobot BMC-3C12[HAS]/S 　　Features: The fingertips are opened in the positive pressure state and clamped in the vacuum state, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by supporting the fingertip distance D. Soft-touch materials are divided into regular [H] and non-...

Introduction: Rorobot Finger Module B6V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot Finger Module FMA8-V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing ...

Introduction: FlexTouch/Rorobot Flange Connection Module FCM-R04 Features: It complies with the ISO 9409-1:2004 standard (i.e. GB/T 14468.1-2006/) and is suitable for most robot flanges on the market. Light weight, suitable for lightweight articulated robots, ...

Introduction: Rorobot BML-20301[H]/S Product parameters Tare weight: 3.5g Maximum load: 30g External gripping force: 0.3N Maximum working frequency: 300 times/min Accuracy range: 0.05mm Safe working pressure: 1 ...

Introduction: Rorobot Robot BML-20005V, B-20005V/S can be used well for small, light and thin special-shaped workpieces between 0.18mm-3mm, even if it is close to the plane, it can also do pinching and grabbing, to ensure that the surface of the product is flawless. For light and small, high blanking accuracy requirements and ...

Introduction: Rorobot BMC-2076D5/S 　　Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G. Soft-touch materials are divided into conventional and non-marking types, ...

Introduction: Rorobot BML-4G64[HAS]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G. Soft-touch materials are divided into regular [H] and non-...

Introduction: Rorobot Finger Module FM-A4V1, Features and Applicable Scenarios: Combination of two-finger modules, compact structure, small space occupation. The spacing and installation angle are not adjustable, and it is suitable for clamping small, light and thin workpieces. Features: Features and applicable scenarios: ...

Introduction:Rorobot Soft Jaw BMC-1G364030[H]/M, is a strengthened version of the single finger soft jaw, the recommended distance between the fingertip and the workpiece is (19-28) mm, the recommended load of the single finger soft jaw is (0-500)G, and the external gripping force is (0-11)N. Features: Positive pressure state fingertip hit ...