Soft Touch/Rorobot Finger Module FE-A3V1 Module width 29mm

Introduction: Rorobot soft beak module BM series can be installed in the connection module [CM] or flange connection module [FCM]; The soft beak module comprises a soft beak and a matching fitting joint; The module assembly is supplied with a straight-through fitting fitting (PN-066) or a side-through fitting fitting (PN-007); Soft beak ...

Introduction: Rorobot BML-20301[H]/S Product parameters Tare weight: 3.5g Maximum load: 30g External gripping force: 0.3N Maximum working frequency: 300 times/min Accuracy range: 0.05mm Safe working pressure: 1 ...

Introduction: Soft Touch/Rorobot Quick Change Module QCM-01R, Quick Change Module is used for automatic quick replacement of spare grippers. The quick-change module [QCM] is installed between the flange connection module [FCM] and the end of the robotic arm, and is divided into the robotic arm side (R-side, installed at the end of the robotic arm) and the gripper side (G-side, installed...

Introduction: Rorobot Robot BML-20005V, B-20005V/S can be used well for small, light and thin special-shaped workpieces between 0.18mm-3mm, even if it is close to the plane, it can also do pinching and grabbing, to ensure that the surface of the product is flawless. For light and small, high blanking accuracy requirements and ...

Introduction: Rorobot Soft Jaw BML-1G071010/S Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type and non-marking type ...

Introduction: Rorobot Finger Module FM-B4V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixing Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Soft-Touch/Rorobot Soft-Touch Module Slip Mounting Plate SMP-14 　　Features: According to the length of the slot, it is divided into SMP-13 / SMP-14 / SMP-15 / SMP-16 It can be used for the assembly between the soft beak module, the connection combination [CM] and the aluminum profile The installation angle of the soft beak module and the ...

Introduction: Rorobot BMC-3C12[H]/S Features: The fingertips are opened in the positive pressure state and clamped in the vacuum state, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by supporting the fingertip distance D. Soft-touch materials are divided into conventional type [H] and non-marking ...

Introduction: Soft Touch/Rorobot Finger F-A3 Features: Finger pattern and fingertip shape: It will affect the coating effect and friction of the workpiece. If you need to customize the shape of the finger or fingertip, please contact customer service. Finger material can be selected conventional ...

Introduction: Rorobot Finger Module B3V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and ...

Introduction: Rorobot Finger Module FM-C4V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixation: Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Soft Touch/Rorobot Module B-20006/S, B-20006/S is a flexible claw with a small structure, especially suitable for strip and rod workpiece grabbing, which can realize wrapping grabbing, non-trace and non-destructive handling and sorting, to ensure that the product will not be scratched, and reduce the defect rate. When multiple soft jaws are connected in series, ...

Introduction: FlexTouch/Rorobot Spring Rod Flange Connection Module FCM-S01 Features: In line with the ISO9409.1:2004 standard (i.e. GB / T 14468-2006/), suitable for most of the robot flanges on the market For mounting soft beak modules or light hand claws ...

Introduction: Rorobot Soft Beak B-3B14 Features: Replaceable flexible chucks The fingertips are open in the positive pressure state, clamped in the negative pressure state, and the fingertips are adjustable from G It can be used as a clamp or external support Recommended for use with soft-touch actuators Product References ...

Introduction: Rorobot Flange Connection Module FCM-R08 Features: Conform to ISO9409-1:2004 (i.e. standard GB/T 14468.1·2006/) and adapt to most of the robots and flanges on the market. It is recommended to carry a large load of 20kg Suitable for non-standard gripper combinations ...

Introduction: Rorobot B-4H18[H]/S Features: The fingertips are open in the positive pressure state, clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by using the external support fingertip distance D. The soft claw material is divided into conventional type [H] and non-marking type [ ...

Introduction: Rorobot BMC-2076D5[P1/S Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type and non-marking ...

Introduction: Rorobot Finger Module FM-B8V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Adjustable Finger Spacing and Angle, Fixing Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) ...

Introduction: Rorobot Finger Module B6V4, Features and Applicable Scenarios: Large clamping force, can be used in series (using screw accessory kit PK) and simplifies the arrangement of the trachea. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm. Features: ...

Introduction: Rorobot BML-20301[H]/S Product parameters Tare weight: 3.5g Maximum load: 30g External gripping force: 0.3N Maximum working frequency: 300 times/min Accuracy range: 0.05mm Safe working pressure: 1 ...