Pressure sensor type PN for industrial applications with display – ifm

On November 18, 2008, the 19th Multinational Instrumentation Conference and Exhibition was held in Beijing International Exhibition Center, at the exhibition, as one of the world's leading manufacturers of electronic sensors in the field of industrial automation, Germany ifm electronics showed its advanced sensors and their corresponding ...

First, the application environment of the weighing system Sensors operating in high-temperature environments should use high-temperature resistant sensors, and especially harsh occasions must also be equipped with heat-insulation, water-cooled or air-cooled devices. For use in alpine areas, load cells with heating devices should be considered. ...

Proximity sensor is a general term for sensors that replace touch detection systems such as limit switches and aim at detecting objects without touching them. It converts the moving and possessive messages of the detected target into electrical signals. ...

Programmable ifm controllers operate using a "sequential scan, continuous loop" approach. 1. Output rewriting stage: When the instruction is fulfilled, the on-off status of the output status register is sent to the input in the output rewriting stage.

On July 9, 2018, the grand Red Dot Awards ceremony was held at the Aalto Theater in Essen, Germany, and the prestigious "Red Dot Planning Award" 2018 was presented. This year's contestants from 59 countries paid tribute to the Red...

1. The exhaust temperature of the refrigeration unit is high, the coolant level of the refrigeration unit is too low, the oil cooler is dirty, the oil filter core is blocked, the temperature control valve is faulty, the oil-off solenoid valve is not energized or the coil is damaged, the oil-cut solenoid valve diaphragm is broken or aging, the fan motor is faulty, the cooling fan is damaged, and the exhaust pipe is not ...

The decentralised AS-i IO-Link master module acts as a gateway between the intelligent IO-Link sensor and the AS-Interface fieldbus. They combine the advantages of the AS-i cabling system with standard IO-Link communication. With IO-Link, connected sensors or actuators can be detailed ...

Vortex flowmeter series instrument because of the use of the environment is special or harsh in the field work sometimes present such and such problems, resulting in production will be affected, vortex flowmeter and orifice flowmeter and V-cone flowmeter are different, as far as the orifice flowmeter is concerned, it is the standard orifice plate and multi-parameter ...

Torque sensor is a component that must be installed in some industrial products, mainly used to measure speed and viewpoint orientation, but different types of sensors have different ways to use and function, what is the classification of torque sensor? Resistance strain ...

1. Inspection interval Detect the stop, start and orientation of elevators and lifting equipment; Detect the orientation of the vehicle to prevent two objects from colliding; Detect the setting orientation of the operating machinery and the limit orientation of the moving machine or components; Detect the abort azimuth of the rotary body, the opening or closing of the valve; Detection of pneumatic or hydraulic cylinders ...

1. Measurement scale: The normal use of the pressure transmitter should not exceed its measurement scale and working condition scale, and the short-term overload is allowed to be 120%. 2. Working environment: The working environment of Germany IFM pressure transmitter should be free of strong corrosion ...

Two directions are detected with one sensor The valve sensor consists of two inductive proximity switches overlapping in the same housing. Depending on the direction of the cam, the upper or lower sensor triggers. Merit: ...

Green City Solutions is committed to improving urban air quality. As a result, they developed CityTree, the world's first bio-skill air filter. The filter is integrated in the UGT505. CityTree uses ...

Selection of sensitivity In general, within the linear scale of the sensor, the higher the sensitivity of the sensor, the better. Because as long as the sensitivity is high, the value of the output signal corresponding to the measured change is relatively large, which is conducive to the signal processing.

The conversion of the pressure to the electrical signal is done by the physical deformation of the strain gauge, and the strain gauge is bonded to the diaphragm of the pressure sensor and wired into a Wheatstone bridge structure. The pressure exerted on a high-frequency pressure sensor causes the diaphragm to flex, which causes the strain gauge to strain. Strain will occur ...

Gas detector is an instrumentation tool for gas leakage concentration detection, which mainly uses sensors to detect the types of gases present in the environment, and gas sensors are used to detect the composition and content of gases. Many environmental factors can affect gas detector sensing ...

1. Encoder own problem: It refers to the problem of the encoder's own components, resulting in its inability to generate and output correct waveforms. In this case, the encoder needs to be replaced or its internal components repaired. 2. Encoder connection cable problem: the probability of this problem is high, and the maintenance is under repair.

1. Sensor scale: (1) In normal use (static test or quasi-static test, the frequency of use is not high), the scale of the sensor should be selected to consider the force value of the measurement, but also to consider the weight of the auxiliary tool (test fixture) and so on.

1. The larger the object, the more light is reflected and the farther the sensing interval is. 2. For visible red light sensors, light colors can be detected at a greater scale than dark colors. The color of the target object has a much smaller effect on the infrared light sensor. Compared to a flat or matte appearance, a highly reflective ...

1. The PCB layout board touches the problem, and when the imitation signal is traced, the imitation signal is not wrapped with imitation, and there is even a possibility that the signal line is directly taken to the power line, which is easy to receive disturbance. Solution: When it is a board, wrap the GND to imitate the signal line. If there is a model ...