Introducing Turck's BI1 series of inductive sensors

A differential pressure sensor is a sensor used to measure the difference between two pressures, and is generally used to measure the pressure difference between the front and rear ends of a certain equipment or component. Typical Applications: It is used to measure the exhaust particle trap (DP ...

(1) Resistance shunt: practice is a resistance with a very small resistance value, when there is a current through, according to Ohm's law, the voltage occurs in the resistance, and the current is known according to the measured voltage value. The resistor shunt has high precision, fast response speed, low cost, simple use, defects, etc.

Ultrasonic sensors In order to ensure the best material flow, the in-plant logistics system often uses conveying equipment, and if you want to run the conveying equipment at high speed, it is necessary to obtain the location information of the container. Turck's RU50 ultrasonic sensor is the ideal solution for inspecting containers in intralogistics systems.

Advantages of capacitive sensors 1. Good temperature stability The capacitance value of capacitive sensors is generally independent of the electrode data, which is conducive to the selection of data with low temperature coefficient, and has little impact on stability due to its own small heat generation. The resistance sensor has copper loss, which is easy to heat up.

First, there is no change in the output of the transmitter when the temperature of the measured medium rises or decreases. This situation is mostly a problem with the sealing of the temperature sensor, which may be because the temperature sensor is not sealed well, or it may be that the sensor is accidentally welded into a small hole during welding.

1. Recognize the type of pressure sensor (1) Electromechanical: The internal mechanical structure of the product, the pressure sensor made of springs, levers, dispatching screws, metal housings, etc., and contact module equipment, does not contain processing circuits inside, and the output is the pressure switch side of the switching quantity.

(1) After proper appearance, the frequency response value of the turck pressure sensor in Germany is verified under normal atmospheric pressure and standard temperature conditions. (2) Verify the accuracy of the coding of the turck pressure sensor in Germany and the corresponding frequency response signal. ...

1. Determination mechanism The commonly used torsional strain gauge is attached to the ductile shaft to be measured with strain adhesive and forms a strain bridge, which supplies power to the strain bridge. The electrical signal of torsion on the elastic shaft is immediately determined. After the strain signal is enlarged, it is changed to the positive and negative parts of the torsional strain after the voltage/frequency change.

Key features and benefits: Electrical reactivity The TTL encoder of the universal line is short-circuited at the output and supplied with a stable output level regardless of the applied operating voltage. resolution Up to 5000 veins ...

Turck's PT1000/2000 series pressure sensors are now available with an IO-Link interface and two programmable switching outputs. In addition to the series' ability to withstand shocks, pressures, and temperature changes, the new products also offer all the advantages of digital communication, including enhanced ...

Turck is expanding its Industry 4.0 portfolio into hazardous areas and is committed to becoming a provider of end-to-end IoT solutions for process automation occupations. As an automation specialist, with the TN-R42/TC Ex, Turck offers not only high-frequency RFID reads and writes that are certified for direct use in ATEX zone 1/21...

1) Pay attention to the structure and data of the object to be measured, and the general laser displacement sensor needs to measure the triangular optical path with intact requirements. If the measured object has deep grooves or messy appearance, it may cause the triangular light path to be occluded, so that it cannot be measured. There are also some light-absorbing materials, such as black rubber and other materials, most of the light intensity will be ...

The photoelectric effect can be divided into two categories: the external photoelectric effect and the internal photoelectric effect, and the internal photoelectric effect can be divided into the photoconductive effect and the photogenerated volt effect. It refers to the phenomenon that electrons in an object escape from the surface of the object under the illumination of light, resulting in photoelectron emission. Equipment made according to the external photoelectric effect ...

The so-called inclination angle is a relative orientation with reference to the horizontal line and the vertical axis. Changes in orientation can be monitored quickly and precisely by means of inclination sensors. The acceleration of gravity is a parameter measured by the sensor. This measurement principle is equivalent to using a plumb line to produce a change of direction in a gravitational field. Turck inclination ...

Turck's linear displacement sensors have an additional measuring stroke of 100 to 4500 mm. It uses the magnetoelastic principle and non-touch measurement method, and provides a high accuracy of μm according to the 16-bit D/A conversion resolution. It can be changed according to the actual application needs through a very simple programming method.

(1) Stable power supply to the proximity sensor separately; (2) the response frequency is in the extra range; ​ (3) There is jitter in the process of object detection, resulting in exceeding the detection area; (4) Multiple probes are tightly connected to each other; ...

Inductive sensors Inductive sensors are capable of detecting metal objects in a non-tactile and wear-free manner. To do this, they use high-frequency communication electromagnetic fields to interact with their targets. Their strengths are durability, robustness, high switching frequencies, and long service life. Cause...

1. Estrangement Do not press or touch the barrier as this may damage or alter its calibration, especially on low pressure scale types. 2. Accessories and hardware With the right pressure, additional fittings and hardware, make sure you have the right thread type and size. If the demand ...

1. Observe whether the appearance of the sensor is deformed and cracked. If this happens, contact the sensor manufacturer to replace the sensor. 2. Find the sensor connection terminal of the weighing controller (weigher) and measure the sensor connection circuit. In general, the excitation voltages (EXC+ and EX...

1. According to the measurement target and measurement environment In order to carry out a detailed measurement work, it is necessary to first consider the principle of the sensor to choose, which needs to be analyzed and many elements can be confirmed. Because, even if the same physical quantity is measured, there are sensors with multiple principles to choose from.