Description: P+F/Laser through-beam sensor OBE20M-R100-S2EP-IO-L Small design, multifunctional mounting options, multiple frequencies to prevent mutual interference (anti-crosstalk), high degree of protection IP69K.
Features:
Compact design with versatile mounting options
DuraBeam Laser Sensors - Durable and can be used like LEDs
IO-link interface for service and process data
Multiple frequencies to prevent mutual interference (anti-crosstalk)
Extended temperature range
-40°C … 60°C
High degree of protection: IP69K
Product parameters
Effective detection distance :0 ... 20 m
Detection range limit: 30 m
Light source: laser diode
Light Type: Modulates visible red light
Laser ratings
Note: Laser, never look directly at the laser beam
Laser class: 1
Wavelength: 680 nm
Beam divergence: > 5 mrad ; d63 < 2 mm with a range of 250 mm ... 750 mm
Pulse length: 1,6 μs
Repetition rate : max. 17,6 kHz
Maximum pulse energy: 9,6 nJ
Spot diameter: approx. 50 mm apart, 20 m apart
Divergence angle : approx. 0,3 °
Ambient light limit: EN 60947-5-2 : 30000 Lux
MTTFd ：440 a
Mission Time (TM): 20 a
Diagnostic Coverage (DC): 0 %
Operating voltage :10 ... 30 V DC
Ripple max :10 %
No-load current
Transmitter: ≤ 13 mA
Receiver: ≤ 13 mA at 24 volts
Protection Class: III
Interface Type: IO-Link (via C/Q = Pin 4)
Transmission rate : COM 2 (38.4 kBaud)
Minimum cycle time: 2,3 ms
Process data bit width
Transmitters
Process data output: 2 bits
receiver
Process data entry: 2 digits
Process data output: 2 bits
SIO Mode Support: Yes
Device ID
Emitter: 0x110402 (1115138)
Receiver: 0x110302 (1114882)
Compatible Primary Port Type : A
Signal output: 2 push-pull (4-in-1) outputs, short circuit protection, reverse polarity protection, overvoltage protection
Switching voltage: max. 30 V DC
Switching current: max. 100 mA, impedance load
Use categories :D C-12 and DC-13
Voltage drop : ≤ 1,5 V DC
Switching frequency: 1250 Hz
Response time: 0,4 ms
Ambient Temperature :
-40 … 60 °C （-40 … 140 °F) to secure the cable
-25 … 60 °C （-13 … 140 °F), movable cables are not suitable for conveyor chains
Storage temperature :-40 ... 70 °C （-40 … 158 °F）
Housing width: 11 mm
Housing height : 37,1 mm
Case depth : 21,5 mm
Degree of protection : IP67 / IP69 / IP69K
Connection: 2 m fixed cable
material
Housing :P C (Polycarbonate)
Optical end-faces :P UMA
Mass: Transmitter: approx. 10 g Receiver: approx. 10 g
Cable length: 2 m
Our customer-centric service concept: the pursuit of a full range of services is a high-quality, high-standard service, the pursuit of every detail of the service process. It is impossible for interests to blossom into brilliant flowers from lies. Only when every process, every action, and every day of service are professional and careful, can we meet or even exceed customer expectations, so that customers can be satisfied and recognized by us. Honest, professional, affordable, and fast, so you can rest assured. "Honest and professional service, affordable price, continuous improvement" is our service philosophy.
This article introduces the P+F/Laser Thru-Beam Sensor OBE20M-R100-S2EP-IO-L products, if you are interested in P+F/P+F/Laser Thru-beam Sensor, please also contact our customer service, we are looking forward to your call, hope our technology and service can bring you a better experience.
|
More on that
|
P+F capacitive sensor CJ10-30GK-WS housing diameter 30 mm
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/UB120-12GM-E5-V1 connector M12
Product Introduction: The transducers used to transmit and receive sound waves are separated, so that the system does not need to wait for the signal attenuation of the transmitter, thus effectively reducing the dead zone. The direct detection type of ultrasonic sensors is available with switching and analog outputs. Direct detection of all support window mode functions ...
|
|
P+F/Ultrasonic sensor UC6000-30GM-2EP-IO-V15
Introduction: The reflector and receiver of this type of ultrasonic sensor are in the same housing. A single ultrasonic transducer is cyclically switched between transmit and receive modes. The target object acts as a reflector of sound waves.
Specifications ...
|
|
P+F/Beam Ultrasonic Barrier UBE1000-18GM40A-SE2-V1
Introduction: There is no electrical connection between the transmitter and receiver, and while the sensor is mounted in such a way that it does not affect the functionality of the ultrasonic through-beam sensor, it is recommended to mount the transmitter face up when the sensor is mounted vertically to prevent the accumulation of dust particles.
...
|
|
P+F/2D Laser Scanner R2000 5-pin M12x1 connector
Product Introduction: The R2000 series combines standard sensors with the latest measurement methods. The R2000 2D laser scanner (also known as 2D LiDAR sensor) is equipped with the innovative Pulse Ranging Technology (PRT) to deliver reliable and extremely precise measurement results with 360° gap-free ...
|
|
P+F/Capacitive sensor CJ4-12GK-N-5M with a rated voltage of 8V
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F sensor NBN40-L2-E0-V1 40 mm non-flush
Introduction: NBN40-L2-E0-V1 is a kind of switch sensor (i.e., non-contact switch), which has the characteristics of travel switch and micro switch, and has sensing performance, and reliable action, stable performance, fast frequency response, long application life, strong anti-interference ability, etc.
|
|
P+F/Double Blessing Timer KC-LCDC-48-2R-230VAC 142g
Introduction: P+F Timer KC-LCDC-48-2R-230VAC easy-to-read, backlit 2-line LCD display with icons for pre-selection and the status of both outputs; Add/subtract via 2 independent inputs, degree of protection IP65 (front).
...
|
|
P+F/Accelerometer ACX04-F99-I-V15 outputs 4 mA~20 mA
Product Introduction: The F99 series accelerometer monitors the strong vibration or acceleration of the wind turbine due to high winds. The sensor has a rugged, environmentally friendly housing and uses a non-contact, reliable detection principle to avoid critical situations.
Specifications:
...
|
|
P+F Capacitive sensor CCB10-30GS55-N1-V1
Introduction: Capacitive sensors can be used to detect targets in almost any material, including metal. These sensors are used in a wide range of applications for level and flow control, mainly liquids, particles and powders.
Give birth...
|
|
P+F/Capacitive sensor NTK-H has a conductor cross-section of 0,34 mm2
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Inductive sensor NBB8-18GM50-E0-M 8mm
Summary: Inductive proximity sensors are the product of choice for most applications that require the precise and non-contact detection of metal objects in machinery or automation. As a pioneer and market leader in the field of sensors, we offer our customers innovative, high-quality inductors.
|
|
P+F/Optical fiber optic sensor SU19.1/110/115 30μs
Product Introduction: Classic Series Fiber Optic Sensor with Display, Slave Module, Push-Pull Output, Fixed Cable, Classic Line with Display, AGC (Automatic Gain Control) for Faster Teach-in, Combined Installation, Easy Wiring, Transparency Recognition, 30μs High Speed Mode.
...
|
|
P+F/Through-beam photoelectric sensor BB10-P/59/76b/103/115e
Introduction: The transmitter and receiver on a thru-beam photoelectric sensor are aligned in opposite directions. The advantage of this is that the beam reaches the receiver directly, so a long detection distance and high excess gain can be achieved. These sensors are capable of reliably detecting almost any object. Angle of incidence, surface characteristics ...
|
|
P+F Inductive Sensor NBB15-30GM50-E0 15mm
Introduction: P+F Inductive Sensor NBB15-30GM50-E0 15mm flush; Longer working distance; Extended temperature range -40 ... +85 °C; Extended operating voltage range; With a variety of mounting options, it is flexible to use.
...
|
|
P+F Inductive Sensor NBB20-U1-A2 4-wire DC
Introduction: Smooth or threaded stainless steel housing for inductive sensors; reverse polarity protection and short circuit protection; LED status indication; M8, M12 connector connection or terminal wiring; PVC, PUR or silicone cable outlet; 2-wire, 3-wire, 4-wire DC, AC, NAMUR and AS ...
|
|
P+F/Switching Amplifier KFD2-SOT3-Ex2 24V DC
Introduction: The K-series isolation barriers provide users with a comprehensive solution to ensure reliable & economical signal transmission between field devices and control rooms. Whether the user selects a single signal isolation module or performs large-scale system integration, the K Series ...
|
|
P+F/Inductive sensor NBN30-L2-E2-V1 30 mm
Introduction: Smooth or threaded stainless steel cylindrical housing for standard inductive sensors; reverse polarity protection and short circuit protection; LED status indicates M8, M12 connector connection or terminal wiring mode; PVC, PUR or silicon cable outlet; 2-wire, 3-wire, 4-wire DC, AC, NAMUR output ...
|
|
P+F/Inductive sensor NBN30-U1-A0/A2 non-flush 30mm
Introduction: Germany P+F/Beijiafu inductive sensor is the use of electromagnetic induction to measure physical quantities such as displacement, pressure, flow, vibration, etc. into the change of the self-inductance coefficient and mutual inductance coefficient of the coil, and then converted by the circuit into the output of voltage or current change, to achieve non-electric to electric ...
|
|
P+F/Inertial Measurement Device IMU360D-F99-B20-V15
Product Description: The new generation of the F99 inclination measurement sensor is ideal for industrial environments due to its simplicity, durability and compact housing. The F99 inclination measurement sensor offers a standardized 4 ... 20 mA analogue interface with a measuring range of 0 ... 360° between, no need for expensive total ...
|
|
Contact
working hours
