Introduction: Xinshida AS900 series 3-in-1 new energy vehicle auxiliary motor controller, for PHEV and EV; High power density; High overload capacity; Built-in voltage, current, temperature detection; Integrated drive protection.
Product parameters
Parameters of the whole machine
DC rated voltage level: DC540V
DC power supply voltage range: DC220V (undervoltage point 150V) - DC750V (overvoltage point)
Dimensions: 515×472×160
Cooling method: air cooling
Communication: CAN 2.0b J1939
Control box auxiliary power supply: 8-36Vdc
Type of strong current connector: waterproof connector and high current connector
Integrated Function: Oil Pump DC-AC & Air Pump DC-AC & DC-DC
DC/AC electrical parameters
Applicable motors: three-phase AC asynchronous motor and permanent magnet synchronous motor
Rated power: 3.7kW&3.7kW
Peak power: 5.6kW &5.6kW
Rated AC output current: 9A&9A
Peak AC output current: 13.5A&13.5A
Overload Capacity: 150%
Rated Controller Efficiency: ≥98%
Output frequency range: 0.00-300Hz
Protection functions: over-temperature, overload, phase-to-phase short circuit, short circuit to ground, overcurrent, overvoltage, undervoltage, phase loss
DC/DC electrical parameters
Start-up time: 1-5s
Load type: lead-acid batteries and on-board electrical appliances for commercial vehicles
Rated power: 3kW
Peak power: 3.5kW
Input voltage range: 200-750Vdc
Conversion efficiency: ≥90% @540V 27.8V 110A
Rated output: DC 27.5±0.5V @ 110A
Rated output current: 110A
Output ripple: 500mV under rated operating conditions<
Working system: non-stop operation
Protection function: equipment overheating, overcurrent, input undervoltage, short circuit, reverse polarity protection; Output overvoltage, short circuit protection, reverse polarity protection, self-reset, etc
Environmental adaptability
Storage temperature: -40°C - +85°C
Degree of protection: IP65
Working environment temperature: -40°C-+65°C
Maximum altitude: 3000 meters for motor controller, 2000 meters for DC-DC
Swept vibration: 1.2mm 10-25Hz; 30m/s² 25——500Hz（QCT413-2002）； ISO16750 frame
Withstand voltage: The dielectric strength of the controller U, V, W, +, and - to the ground (shell) can withstand a DC voltage with a duration of 1 minute, and the leakage current of 3000V is less than 10mA
Insulation resistance: The steady-state test insulation resistance must be greater than 20MΩ ISO6469-3
Humidity: 5-95%, no condensation
Safety grounding: The resistance of the conductive part accessible to the controller and the grounding point of the housing is less than 0.1Ω
The company respects the enterprise spirit of "practicality, hard work and responsibility", and creates a good corporate environment with integrity, win-win, and business philosophy, and takes a new management model, perfect technology, thoughtful service, and excellent quality as the foundation for survival. We always adhere to: customer first, serve customers attentively, and insist on impressing customers with their own services. Always adhering to the business philosophy of "integrity, win-win", relying on excellent prices, excellent quality, fast delivery and pre-sales consultation and after-sales service to win the trust of our customers.
This article introduces the new STEP inverter AS900 series rated voltage DC540V products, if you are interested in the new STEP inverter, please also contact our customer service, we are looking forward to your call, hope our technology and service can bring you a better experience.
|
More on that
|
The new STEP motion controller SC20-A3L has a RAM capacity of 1M
Introduction: Xinshida/STEP motion controller SC20-A3L, economical PAC, developed based on CoDeSys platform, fully supports IEC61131-3 standard programming language; Support PLCopen toolkit, can realize single-axis, multi-axis movement, IO control, support basic electronic gears, electronic ...
|
|
Xinshida/STEP Motion Controller SC30-A6H RAM capacity 2G
Introduction: Xinshida/STEP motion controller SC30-A6H, medium-sized PAC, integrated control, one-stop connection, one-platform design; Based on the CoDeSys platform, it fully supports the IEC61131-3 standard programming language; Support configuration programming, support EtherCAT, CANOpen, Etherne...
|
|
Xinshida/STEP Motion Controller SC30-A6L RAM capacity 2G
Introduction: Xinshida/STEP motion controller SC30-A6L, medium-sized PAC, integrated control, one-stop connection, one-platform design; Based on the CoDeSys platform, it fully supports the IEC61131-3 standard programming language; Support configuration programming, support EtherCAT, CANOpen, Etherne...
|
|
Xinshida/STEP high-voltage inverter ME800 vibration is less than 0.5g
Introduction: ME800 series high-voltage inverter has power electronics technology and vector control technology in one of the high-high voltage source high-voltage inverter, it greatly suppresses the input harmonic current on the grid side through the phase-shifting rectifier transformer, and realizes the voltage superposition through the cascade of multi-stage H-bridge power units.
|
|
Xinshida/STEP High Voltage Solid State Soft Starter AHS80 voltage range 6/10kV
Introduction: Xinshida/STEP high-voltage solid-state soft starter AHS80, the working principle of the soft start device is to control the output voltage by controlling the trigger angle of the thyristor, so as to meet the different current and voltage requirements in the process of motor starting. During the motor start-up process, according to the pre-set ...
|
|
The input voltage of AS-M21 is 380-440V
Introduction: AS M21 series inverter is a universal inverter designed for China's small power segment motor speed control market, with typical VF control technology, but also using no speed sensor vector control technology, the product integrates Germany technology, Chinese manufacturing technology, light and heavy load in one, ...
|
|
Xinshida/STEP inverter AS510 series 30-450kW
Introduction:Xinshida/STEP inverter AS510 series adopts advanced controllable rectification technology, with LCL filter to achieve active rectification, providing constant DC power supply and energy feedback for the system, and can run 1 or more inverter units on the DC bus to form a four-quadrant operation of multi-...
|
|
Xinshida/STEP controller AMC1600P The input voltage is 24V
Introduction: Xinshida/STEP controller supports 6 axes, 36 inputs, and 24 outputs AMC1600P.
Product parameters
Input voltage: 24V
Universal input minimum current: 2mA
Universal input maximum current: 8mA
Rated output current: 1A (single channel max ...
|
|
Xinshida/STEP common DC multi-drive inverter ME700 frequency 2~5kHz
Introduction: ME700 series engineering drive is a common DC multi-drive inverter specially designed and developed for heavy-duty machinery and equipment in the rubber industry. The product adopts advanced vector control technology and torque control technology, which not only has the same excellent control performance as the international reliable inverter.
|
|
The AHS series of STEP soft starters has a voltage range of 6/10kV
Introduction: Xinshida/STEP soft starter AHS series, the working principle of the soft start device is to control the output voltage by controlling the trigger angle of the thyristor, to meet the different current and voltage requirements in the process of motor starting. During the motor start-up process, according to the pre-set starting ...
|
|
Xinshida/STEP servo motor 60B series
Introduction: Xinshida/STEP servo motor 60B series
Product parameters
Rated power: 200W——400W
Rated line voltage: 220VAC (-15-+10%), 50-60Hz
Rated line current: 1.55A——2.6A
Rated speed: 300 ...
|
|
Xinshida/STEP vector inverter AS450 input current 3.7~1044A
Introduction: Xinshida AS450 is a universal vector inverter. The product not only has typical V/F control technology, but also adopts no speed sensor vector control technology, closed-loop vector control and torque control technology, and combines the domestic application characteristics to further strengthen the reliability of the product.
|
|
The new STEP motion controller SC20-A3H6 has a RAM capacity of 32M
Introduction: Xinshida/STEP motion controller SC20-A3H6, economical PAC, developed based on CoDeSys platform, fully supports IEC61131-3 standard programming language; Support PLCopen toolkit, can realize single-axis, multi-axis movement, IO control, support basic electronic gears, electronic ...
|
|
Xinshida/STEP Motion Controller SC30-B6H RAM capacity 1G
Introduction: Xinshida/STEP motion controller SC30-B6H, medium-sized PAC, integrated control, one-stop connection, one-platform design; Based on the CoDeSys platform, it fully supports the IEC61131-3 standard programming language; Support configuration programming, support EtherCAT, CANOpen, Etherne...
|
|
STEP Inverter AS720 Series 380-460VAC
Introduction: The AS720 series of STEP inverter is an airborne all-in-one product developed for the HVAC industry based on the mature hardware platform of Xinshida. The inverter is cooled by air conditioning refrigerant, with high power density, and the design process takes into account the working environment of HVAC, installation ...
|
|
The efficiency of the ME500 high-performance vector inverter is ≥0.95
Introduction: ME500 series high-performance vector inverter not only has typical V/F control technology, open-loop vector control technology, closed-loop vector control and torque control technology, but also adopts synchronous open-loop vector control technology, synchronous closed-loop vector control technology, and combines the domestic application characteristics, ...
|
|
Xinshida/STEP inverter AS560 series rated power 11~15kW
Introduction: Xinshida AS560 two-in-one product is the integration and development of AS560 inverter and DCDC two platforms. High integration, compact size, easy for customers to use.
Product parameters
Inverter rated power: 11—— ...
|
|
Xinshida/STEP servo motor 130SH
Introduction: Xinshida/STEP servo motor 130SH
Product parameters
Rated power: 1.0kW——3kW
Number of pole pairs: 5
Rated torque: 4.77N.m——14.3N.m
Maximum torque: 14.3N.m——42.9N.m
Rated speed: 200 ...
|
|
Xinshida/STEP water pump inverter AS170 input voltage 460V
Introduction: AS170 series motor integrated inverter is a high protection level motor drive all-in-one machine developed by Shanghai Singrina Xinshida Motor Co., Ltd., which adopts a unique appearance design and installation method, with local and remote control mode, which is more convenient and reliable to install and use.
|
|
Xinshida/STEP bus IO module ET1616A input voltage 24VDC
Introduction: The new Shida/STEP bus IO module ET1616A
Product parameters
Input channels: 16 channels
Input voltage: 24VDC
Signal input type: optocoupler input
Input logic: Selectable Active-High
Input current: 7mA——15mA
...
|
|
Contact
working hours
