Introduction: ME800 series high-voltage inverter has power electronics technology and vector control technology in one of the high-high voltage source high-voltage inverter, it greatly suppresses the input harmonic current on the grid side through the phase-shifting rectifier transformer, and realizes the voltage superposition through the cascade of multi-stage H-bridge power units, with excellent high-voltage sine wave output, can directly drive high-voltage motors, without installing any filters, harmonic indicators in line with IEC std 519-1992 (International Electrotechnical Commission) and GB/T 12668.4-2006 (National Standard) requirements for harmonics in power grids.
Features:
Flexible terminal extension, no PLC required.
High-quality drive of the motor.
Low harmonic content.
Speed tracking is activated.
Mechanical unit bypass.
Frequency conversion without disturbance switching.
Curve display.
Bus voltage self-balancing technology.
Endurance after power failure.
The cycle softens.
Synchronizer control.
Product parameters
input
Inverter power range: 400-3000kW
Input line voltage: 3.0/6.0/10.0kV
Allowable Error of Input Voltage: ±15%
Input-side power factor: >0.95 when the load exceeds 20%.
Input side higher harmonics: 10kV <3% when the load exceeds 50% 6kV <4%
output
Output line voltage: 3.0/6.0/10.0kV
Output frequency resolution: 0.01Hz
Control functions
Control mode: closed-loop vector control
Closed-loop speed regulation accuracy: 1‰
Speed range: 0.5-120Hz
Overload capacity: 200% overload time 1 minute
Acceleration time: 0.1 - 3200 seconds
High and low voltage isolation: Optical fiber isolation
Digital input and output ports: 16 digital inputs, 8 digital outputs (can be expanded according to user needs)
Analog input and output ports: 4 x 0-10V/4-20mA input, 4 x 0-10V voltage output, 4 x 4-20mA current output
Communication interface: Modbus bus, CAN communication interface and 485 communication interface
Optional communication interface: Profibus, etc., can meet the special communication requirements of customers
Encoder Interface: 1 rotary encoder interface
Degree of protection: IP30 (plus air duct IP31)
Use environment
Operating ambient temperature: 0-+50°C
Storage and transport temperature: -20-+70°C
Installation: Indoor
Humidity: <90% non-condensing
Altitude: Above 1000 meters, derating is required
Vibration: 0.5g or less
The company respects the enterprise spirit of "practicality, hard work and responsibility", and creates a good corporate environment with integrity, win-win, and business philosophy, and takes a new management model, perfect technology, thoughtful service, and excellent quality as the foundation for survival. We always adhere to: customer first, serve customers attentively, and insist on impressing customers with their own services. Always adhering to the business philosophy of "integrity, win-win", relying on excellent prices, excellent quality, fast delivery and pre-sales consultation and after-sales service to win the trust of our customers.
This article introduces the new Shida/STEP high voltage inverter ME800 vibration 0.5g below the product, if you are interested in the new Shida/STEP inverter, please also contact our customer service, we look forward to your call, hope our technology and service can bring you a better experience.
|
More on that
|
Xinshida/STEP High Voltage Solid State Soft Starter AHS80 voltage range 6/10kV
Introduction: Xinshida/STEP high-voltage solid-state soft starter AHS80, the working principle of the soft start device is to control the output voltage by controlling the trigger angle of the thyristor, so as to meet the different current and voltage requirements in the process of motor starting. During the motor start-up process, according to the pre-set ...
|
|
Xinshida/STEP vector inverter AS180 input current 5.3A~1186A
Introduction: AS180 series inverter is a general-purpose inverter designed for the Chinese market. The product adopts German technology, made in China, and combines the domestic application characteristics, which further strengthens the reliability of the product, the adaptability of the environment, and the customized and industrialized design.
|
|
Xinshida/STEP Motion Controller SC30-A6H RAM capacity 2G
Introduction: Xinshida/STEP motion controller SC30-A6H, medium-sized PAC, integrated control, one-stop connection, one-platform design; Based on the CoDeSys platform, it fully supports the IEC61131-3 standard programming language; Support configuration programming, support EtherCAT, CANOpen, Etherne...
|
|
The new STEP motion controller SC20-A3L has a RAM capacity of 1M
Introduction: Xinshida/STEP motion controller SC20-A3L, economical PAC, developed based on CoDeSys platform, fully supports IEC61131-3 standard programming language; Support PLCopen toolkit, can realize single-axis, multi-axis movement, IO control, support basic electronic gears, electronic ...
|
|
The input voltage of AS-M21 is 380-440V
Introduction: AS M21 series inverter is a universal inverter designed for China's small power segment motor speed control market, with typical VF control technology, but also using no speed sensor vector control technology, the product integrates Germany technology, Chinese manufacturing technology, light and heavy load in one, ...
|
|
Xinshida/STEP Motion Controller SC30-A6L RAM capacity 2G
Introduction: Xinshida/STEP motion controller SC30-A6L, medium-sized PAC, integrated control, one-stop connection, one-platform design; Based on the CoDeSys platform, it fully supports the IEC61131-3 standard programming language; Support configuration programming, support EtherCAT, CANOpen, Etherne...
|
|
The efficiency of the ME500 high-performance vector inverter is ≥0.95
Introduction: ME500 series high-performance vector inverter not only has typical V/F control technology, open-loop vector control technology, closed-loop vector control and torque control technology, but also adopts synchronous open-loop vector control technology, synchronous closed-loop vector control technology, and combines the domestic application characteristics, ...
|
|
The STEP Motion Controller AMC1610C-016 has a capacity of 512MB
Introduction: Xinshida/STEP Motion Controller AMC1610C-016, special aircraft motion controller; Based on the CoDeSys platform, it fully supports the IEC61131-3 standard programming language; Support configuration programming, support EtherCAT, CANOpen, EthernetIP and other industrial fieldbus protocols ...
|
|
Xinshida/STEP controller AMC1600P The input voltage is 24V
Introduction: Xinshida/STEP controller supports 6 axes, 36 inputs, and 24 outputs AMC1600P.
Product parameters
Input voltage: 24V
Universal input minimum current: 2mA
Universal input maximum current: 8mA
Rated output current: 1A (single channel max ...
|
|
Xinshida/STEP inverter AS560 series rated power 11~15kW
Introduction: Xinshida AS560 two-in-one product is the integration and development of AS560 inverter and DCDC two platforms. High integration, compact size, easy for customers to use.
Product parameters
Inverter rated power: 11—— ...
|
|
The AS800 inverter is IP30 rated
Introduction: Xinshida/STEP inverter AS800 greatly suppresses the input harmonic current on the grid side through the phase-shifting rectifier transformer, realizes voltage superposition through the cascade of multi-stage H-bridge power units, has excellent high-voltage sine wave output, and can directly drive high-voltage motors, without installing any...
|
|
Xinshida/STEP Inverter AS520 Series Torque accuracy±5%
Introduction: AS520 series products are an inverter drive unit developed for the use of common DC bus. The product adopts the best vector control technology and torque control technology, which not only has the same excellent control performance as the first-class inverter, but also combines the hoisting machinery industry ...
|
|
The new STEP motion controller SC20-A3H6 has a RAM capacity of 32M
Introduction: Xinshida/STEP motion controller SC20-A3H6, economical PAC, developed based on CoDeSys platform, fully supports IEC61131-3 standard programming language; Support PLCopen toolkit, can realize single-axis, multi-axis movement, IO control, support basic electronic gears, electronic ...
|
|
Xinshida/STEP bus type open operation control platform AMC1600E
Introduction: Xinshida/STEP bus open operation control platform is an open operation control platform launched by Xinshida AMC1600E Support IEC6113-3 programming, support 16-axis bus and 6-axis pulse hybrid control, HMI, IO, DA, AD can be flexibly configured according to the actual situation of customers.
...
|
|
Xinshida/STEP low-power inverter AS-M20 rated frequency 50/60Hz
Introduction: AS-M20 series inverter adopts the best non-speed sensor vector technology, the best motor parameter identification, the best online estimation technology and the best flux estimation technology, both in the speed regulation range and in the dynamic response, the control accuracy and low-frequency torque have been greatly improved, AS...
|
|
Xinshida/STEP bus IO module ET1616A input voltage 24VDC
Introduction: The new Shida/STEP bus IO module ET1616A
Product parameters
Input channels: 16 channels
Input voltage: 24VDC
Signal input type: optocoupler input
Input logic: Selectable Active-High
Input current: 7mA——15mA
...
|
|
Xinshida/STEP common DC multi-drive inverter ME700 frequency 2~5kHz
Introduction: ME700 series engineering drive is a common DC multi-drive inverter specially designed and developed for heavy-duty machinery and equipment in the rubber industry. The product adopts advanced vector control technology and torque control technology, which not only has the same excellent control performance as the international reliable inverter.
|
|
The ADT-8969G1 motion control card can control 60 servos
Introduction: The ADT-8969G1 is a six-axis motion control card based on the computer PCI bus, which can support up to 10 control cards in one system and control 60 servo/stepper motors. It has a variety of acceleration and deceleration of T-type, S-type and E-type, point position and trajectory ...
|
|
Xinshida/STEP Motion Controller SC30-B6H RAM capacity 1G
Introduction: Xinshida/STEP motion controller SC30-B6H, medium-sized PAC, integrated control, one-stop connection, one-platform design; Based on the CoDeSys platform, it fully supports the IEC61131-3 standard programming language; Support configuration programming, support EtherCAT, CANOpen, Etherne...
|
|
Xinshida/STEP bus motion control card ADT-6329E communication cycle 250us-4ms
Introduction: Xinshida/STEP bus motion control card ADT-6329E, ** large support for 64 nodes, with motion trajectory pre-processing planning function, support for four groups of independent pre-processing interpolation channels, ** support for 32-axis interpolation, a variety of acceleration and deceleration control, space arc interpolation, logic position variable ring ...
|
|
Contact
working hours
