Profis touch screen repair method

Create Date: 2024-8-30 12:03:23|Source: Proface/Proface

A simple repair method for the Profis touch screen.

The touch screen is not allowed

Solution: This phenomenon may be that after the maintenance and use of the Profis touch screen for a period of time, the reflective stripes around the screen are covered with dust, which can be wiped with a dry soft cloth, and then cut off the power, restart the computer, and recalibrate. It is also possible that the reflective streaks of the sound wave screen are slightly damaged, and if this happens, it cannot be completely repaired.

The touch screen is not responding.

Solution: First, check whether the wiring interface in the maintenance process of Profis touch screen is loose, and then check whether there is a conflict between the serial port and the interrupt number. If there is a conflict, adjust resources to avoid conflicts. Check whether there are cracks on the surface of the touch screen, and replace them in time if there are cracks. It is also necessary to check the touchscreen surface for dust and dirt. If available, wash with a soft cloth. Observe whether the indicator light on the control box is working properly. Normally, the indicator light is green and flashing.

The touch screen has a long response time.

Solution: This may be a moving water droplet sticking to the touch screen, just wipe it with a dry soft cloth. It could also be that the host level is too low, such as the clock frequency is too low. In this case, the host can be replaced.

The touch screen is partially unresponsive.

Solution: This may be a partial coverage of the reflective streaks of the touch screen. At this time, the maintenance of the Profis touch screen can be wiped with a dry soft cloth. It is also possible that the reflective stripes of the touch screen are partially scraped off by a hard object and cannot be repaired.

The touch screen is fine, but the computer is not operable.

Solution: This may be before the host starts to load the touch screen driver, the touch screen control card receives the operation signal. Profis touch screen maintenance is simply to cut off the power and then start the computer. It is also possible that the touch screen driver version is too low and a new driver needs to be installed.

More on that

	Profis - the human-machine interface is not easy to touch Judgment and elimination of common faults of touch screen 1. Analysis and treatment method of surface acoustic wave touch screen fault phenomenon Fault 1: Touch deviation Phenomenon: The position of the finger touch does not coincide with the mouse arrow. Analysis: After installing the driver, when correcting the position, there is no vertical touch ...
	There are several common fault operation methods for Pro-face Pro-face touch screen repair Pro-face Pro-face touch screen repair problems encountered and the specific process of solving. 1. The touch screen is not allowed. A surface acoustic touch screen, touching the part of the monitor screen with your finger cannot complete the corresponding operation normally. Solution: This phenomenon may be Pro-face ...
	SP5000X Series—The flagship outdoor programmable HMI designed by world-class experts HMIs are designed to facilitate the efficient use of time and human capital, but today's business developments bring new challenges to traditional HMI applications. As business continues to innovate and new opportunities emerge, we must adapt and deliver the technology needed for business growth.
	Japan Profis finally ushered in the 12.1 and 15-inch economy models in 2020 Profis launched a new series of STW6000, from 4.3 inches to 15.6 inches, the products have now passed the testing stage, and are expected to be put into production and launched as soon as possible
	<人机界面中心架构解决方案> The "mobile operation to improve efficiency" HMI host module (labeled with QR code) is used to perform HMI operations on the mobile terminal This HMI Central Architecture solution is for those responsible for maintaining and managing a wide range of devices. Using the combination of HMI host module + tablet PC, there is no need to install multiple HMIs, which saves space and reduces costs, and effectively improves the on-site ...
	Pro-face: In the digital age, HMI has evolved again. Driven by intelligent manufacturing, the development of the manufacturing industry places more emphasis on human-machine integration and interaction and coordination, and benefits from the needs of all walks of life for efficient production, data security, remote services, etc., and human-machine interface (HMI) has been widely used. ...
	How to empower production with HMI Centric The human-machine interface (HMI)-centric concept is actually an IIoT solution where we leverage people and the latest digital technologies.
	Profis – Does it take manpower to get IT+OT computing information and act without any restrictions across the architecture? The Pro-face HMI and IPC can be connected to a wide range of devices. They connect with robots, inverters, motion controllers, PLCs, and more. More than 1,200 device protocols are compatible, and counting. Compatibility with major open networks will also allow for the use of an almost unlimited number of settings.
	<人机界面中心架构解决方案> "Simple and safe remote maintenance" HMI + WiFi router + smartphone This HMI central architecture solution is for OEMs who want to provide remote maintenance services to their end users. One of the problems OEMs face when starting remote maintenance is the difficulty of setting up a network environment. With a human-machine interface (HMI) central architecture, even if the network cannot be established or the end user is present...
	About HMI Centric HMI Centric concept The human-machine interface (HMI) is the window between humans and machines, allowing both operators and managers to access the information they want, on any device or network, in the way they want. HMI Central Architecture Solution (HMI C...
	Proface-GP4000R series, unique full-flat mounting The GP4000 series rear-mount model is a human-machine interface product that can be installed behind the control panel of the device. Generally, the installation of human-machine interface products is generally installed from the front to the back of the panel, and its outer frame protrudes from the surface of the panel. As a manufacturer with world-class industrial design concepts, Pro-face ...
	The 30th anniversary of the launch of the Pro-face programmable HMI GP series Pro-face, the global human-machine interface specialist, will celebrate the 30th anniversary of its programmable HMI GP series in February 2019! The proface programmable HMI GP series products began to receive orders in November 1988, 198 ...
	Celebrate the 30th anniversary of the Pro-face programmable HMI GP series In February 2019, Pro-face, the global human-machine interface (HMI) specialist, will celebrate the 30th anniversary of its programmable human-machine interface GP series! The Pro-face programmable HMI GP series began to be ordered in November 1988 and officially launched in February 1989. Since then, Pro-f ...
	Profis touch screen stuttering solution What should I do if the picture is stuck? cause A large number of parts on the front layer and painting make it possible to draw complex processes on the front layer, which can cause the HMI to be too slow to respond. When using the animation feature, the pre-layer and the base layer represent the configured domains. The preceding and basic layers are distinguished by a layer separator. Notes: As ...
	Get better visualization and more information! ET6000 series The ET6000 series has a high cost performance ratio and sufficient functions. In addition, it is equipped with easy-to-migrate software and compatible hardware. As a new generation of HMI products launched by the HMI Centric (Human Machine Interface Centric Architecture) concept, the functions and performance of the device can be significantly improved.
	New members of the flagship programmable HMI SP5000 series: standard host module, 12-inch advanced display module! The SP5000 series serves as a smart entry point to the device, which can know the device status, guide the user to use, and manage the data through the connected system. The new "standard" host modules focus on performance. In particular, the display and touch responsiveness of today's human-machine interfaces have been improved. ...
	Profis continues to raise the level of HMI comprehensive application From the beginning of its establishment, Pro-face has been committed to becoming the best interface for global users, and has always insisted on achieving the ultimate, from products to services, from price to value, from ideals to ideas, and many technical ingenuity has made it constantly innovate in products. Pro-face is a pioneer in the HMI industry ...
	Profis—GP4000H: Limitation when the system menu is displayed Do not operate the function keys/operation switches when the system menu is displayed.
	Profis touch screen programming software installation tutorial Profis Touch Screen Programming Software is a very professional programming software. It is the screen and logic programming software developed by Pro-face for its human-machine interface contact screen, which supports dedicated human-machine interface and open human-machine interface (according to PC), which can be completed with data compatibility, ...
	How to wire the PFXZPBMPX16Y82 (DIO) of the Ploface PS5000 series? DIN rail terminal block and connection cable included. No special cables are required. The terminals can be wired in the cable. Connecting cable: DSUB-37Pin specially shielded conductor cable (2 m) DIN Rail Terminal Block: A low-cost, general-purpose DIN rail mounting screw terminal unit. Enclosure ...