Get better visualization and more information! ET6000 series

HMIs are designed to facilitate the efficient use of time and human capital, but today's business developments bring new challenges to traditional HMI applications. As business continues to innovate and new opportunities emerge, we must adapt and deliver the technology needed for business growth.

To find out if the backlight is user-replaceable, check your device's model and version number (Rev.). *The version number of your GP is displayed on the label attached to the device. For details on backlight replacement, refer to the hardware manual or backlight replacement guide. The following are the maintenance ...

The human-machine interface (HMI)-centric concept is actually an IIoT solution where we leverage people and the latest digital technologies.

The Pro-face HMI and IPC can be connected to a wide range of devices. They connect with robots, inverters, motion controllers, PLCs, and more. More than 1,200 device protocols are compatible, and counting. Compatibility with major open networks will also allow for the use of an almost unlimited number of settings.

DIN rail terminal block and connection cable included. No special cables are required. The terminals can be wired in the cable. Connecting cable: DSUB-37Pin specially shielded conductor cable (2 m) DIN Rail Terminal Block: A low-cost, general-purpose DIN rail mounting screw terminal unit. Enclosure ...

With the advancement of intelligent manufacturing, the development of the manufacturing industry places more emphasis on human-machine integration and interaction and coordination, benefiting from the needs of all walks of life for efficient production, data security, remote services, etc., and human-machine interface (HMI) has been widely used. At present, the traditional manufacturing industry is undergoing a digital transformation.

The intelligent human-machine interface (smart entrance) can be used as a gateway terminal to securely connect the equipment (device) and the production control room of the factory production site by building two different networks. At the production site, human-machine interfaces and industrial computers have always been used as operator panels. Human-machine ...

This HMI central architecture solution is for OEMs who want to provide remote maintenance services to their end users. One of the problems OEMs face when starting remote maintenance is the difficulty of setting up a network environment. With a human-machine interface (HMI) central architecture, even if the network cannot be established or the end user is present...

Profis Touch Screen Programming Software is a very professional programming software. It is the screen and logic programming software developed by Pro-face for its human-machine interface contact screen, which supports dedicated human-machine interface and open human-machine interface (according to PC), which can be completed with data compatibility, ...

Pro-face Pro-face touch screen repair problems encountered and the specific process of solving. 1. The touch screen is not allowed. A surface acoustic touch screen, touching the part of the monitor screen with your finger cannot complete the corresponding operation normally. Solution: This phenomenon may be Pro-face ...

What should I do if the picture is stuck? cause A large number of parts on the front layer and painting make it possible to draw complex processes on the front layer, which can cause the HMI to be too slow to respond. When using the animation feature, the pre-layer and the base layer represent the configured domains. The preceding and basic layers are distinguished by a layer separator. Notes: As ...

Judgment and elimination of common faults of touch screen 1. Analysis and treatment method of surface acoustic wave touch screen fault phenomenon Fault 1: Touch deviation Phenomenon: The position of the finger touch does not coincide with the mouse arrow. Analysis: After installing the driver, when correcting the position, there is no vertical touch ...

A simple repair method for the Profis touch screen. The touch screen is not allowed Solution: This phenomenon may be that after the maintenance and use of the Profis touch screen for a period of time, the reflective stripes around the screen are covered with dust, which can be wiped with a dry soft cloth, and then cut off the power and restart ...

An outdoor programmable HMI has been developed that can be read in direct sunlight and used in extreme temperatures. Enhanced information display performance and operability for a wide range of applications in harsh environmental conditions, including special purpose vehicles such as fire trucks, construction equipment, ...

Pro-face, the global human-machine interface specialist, will celebrate the 30th anniversary of its programmable HMI GP series in February 2019! The proface programmable HMI GP series products began to receive orders in November 1988, 198 ...

Even if you perform error checking, the project data is free of warnings and errors, and the error check workspace and results are not displayed. memorandum Even if there are no warnings and errors, the error checking workspace is displayed, 1. Click [Preferences] for [View] on the menu. ...

In February 2019, Pro-face, the global human-machine interface (HMI) specialist, will celebrate the 30th anniversary of its programmable human-machine interface GP series! The Pro-face programmable HMI GP series began to be ordered in November 1988 and officially launched in February 1989. Since then, Pro-f ...

The SP5000 series serves as a smart entry point to the device, which can know the device status, guide the user to use, and manage the data through the connected system. The new "standard" host modules focus on performance. In particular, the display and touch responsiveness of today's human-machine interfaces have been improved. ...

Do not operate the function keys/operation switches when the system menu is displayed.

Profis launched a new series of STW6000, from 4.3 inches to 15.6 inches, the products have now passed the testing stage, and are expected to be put into production and launched as soon as possible