A brief introduction to SIASUN flexible multi-articulated robot and its characteristics

On November 7, the 2022 Global Industrial Internet Conference was held at the Shenyang New World Expo, and this conference continued the theme of "Empowering High-quality · Creating New Kinetic Energy", highlighting the display of achievements, international characteristics, scene advantages, cooperation and exchanges, and further demonstrating the "digital butterfly change" of Liaoning's industry.

Sort out the phenomenon of a robotic arm noise, if such a phenomenon is found on site, please overhaul the equipment as soon as possible! Safety Matters: It should be said that once the air pressure of the balancer is released, the phenomenon of 2 and 3 shafts falling may occur. At this time, if you release the motor brake ...

1. Ultrasonic navigation and positioning technology Ultrasonic navigation also works similarly to laser and infrared, usually by the emitting probe of the ultrasonic sensor, which emits ultrasonic waves, which encounter obstacles in the medium and return to the receiving device. By receiving its own emitting ...

(1) Oxygen therapy 1. Respiratory diseases Chronic obstructive pulmonary disease, pulmonary hypertension, cor pulmonale, respiratory failure, etc. 2. Sleep apnea syndrome 3. Cardiovascular and cerebrovascular diseases Angina pectoris, myocardial infarction, heart failure, cerebral hemorrhage, etc.

First, the shape of the spray amplitude is biased to one side of the center of gravity Because the center hole of the air cap or the atomizing hole is blocked, the atomizing cap can be cleaned or replaced. Second, the spray gun sprays to the left or right There are two reasons, the first is that the sector control hole on one side of the air cap is blocked, and the second is ...

1. Connect the trachea first, so that the air pressure of the manipulator barometer is between 4kg-8kg. 2. Turn on the power switch of the manipulator, and open the function key of the manipulator on the control panel of the injection molding machine. 3. After the injection molding machine is completed, manually put down the mechanical arm and adjust the arm to descend ...

1. Robot system failure (1) A collision occurred. It may be due to deviations in the assembly of the workpiece or inaccurate TCP of the welding gun, the assembly can be checked or the TCP of the welding torch can be corrected. (2) If there is an arc fault, the arc cannot be initiated. It may be due to the fact that the welding wire is not in contact with the workpiece or process parameters.

The "embedded parts" robot intelligent welding system developed by SIASUN Robot Automation Co., Ltd. has been successfully delivered and applied in China Gezhouba Group Electromechanical Construction Co., Ltd. The realization of "embedded parts" intelligent welding is the first domestic robot. "Embedded" means the installation of ...

On November 18, the 2022 Liaoning International Fair for Investment and Trade (hereinafter referred to as the Liaoning Fair) kicked off in Shenyang. As the largest open platform in Liaoning Province, this year's Liaoning Fair will strengthen cooperation and exchanges with well-known manufacturers at home and abroad with the theme of "Smooth Open Channels and Shared Green Development".

(1) Establish the workpiece coordinate system; (2) divide the workpiece into a field shape, set the length L and width W of the workpiece, and the number of cells m, n and the finding height z1 in the length and width directions; (3) determine the orientation path, and the orientation path comprises a plurality of right-angle inflection points and the long ...

1. Compared with ordinary manual spraying, the spraying robot spraying quality is higher The spraying robot sprays precisely according to the trajectory, without offset and perfectly controls the start of the spray gun. Ensure that the specified coating thickness and the amount of deviation are controlled to a minimum. 2. Compared with ordinary manual spraying, ...

　　1. When teaching, try to avoid standing between the robot and the workpiece or between the robot and the fixed object, so as to avoid the abnormal actions of the KUKA robot causing harm to the human body; 2. Pay attention to the teaching speed when teaching: When the robot is close to the welding gun, the welding gun should be taught at a lower speed. ...

Robot maintenance before start-up of the inspection work: 1. The equipment must be checked before starting, and the equipment can only be turned on after confirming that the equipment is in good condition; 2. Inspect and clean the operation site to ensure that there are no flammable materials (such as tarpaulin, waste oil gloves, paint, coke water, etc.) and no air leakage; ...

1. The flatness of the bottom surface of the single-axis manipulator installation is not up to standard. The installation bottom plane of the single-axis manipulator is too large, which will lead to the forced locking of the bottom surface of the electric slide table, resulting in the strong bending deformation of the bottom surface of the slide table, linear guide rail and ball screw. If it is light, it will increase the running resistance of the single-axis manipulator, and the weight ...

1. Multi-degree-of-freedom motion, the spatial angle between each degree of freedom is a right angle. 2. Automatically controlled, reprogrammable, all movements are run according to the program. 3. It is generally composed of a control system, a drive system, a mechanical system, and an operating tool. 4、 ...

On March 19, the winners of the 7th China Industry Award, the highest award in China's industrial field, were officially announced in Beijing, and SIASUN won the nomination award of China Industry Award for its outstanding performance in scientific and technological innovation, brand culture and intelligent manufacturing. This honor reflects China's ...

1. The lifting capacity of the manipulator shall not exceed the lifting capacity. 2. Do not stretch out your hands, feet and any part of your body when hanging. 3. Do not put your hands or fingers into the gap of the manipulator. 4. During operation, the face and hands shall not extend to the upper part of the manipulator attachment.

In recent years, due to the impact of the new crown pneumonia epidemic and the market environment, automobile sales around the world have generally declined to varying degrees. However, China's own brand "Hongqi" has risen against the trend in the downturn of the world auto market, and "Hongqi H9" has become a C+-level high-tech in China's automobile industry.

Manipulator alarm release method ▲When the step is temporarily stopped (automatic operation does not stop) 1. Check and dismiss the reason displayed on the alarm screen. ▲When an automatic stop alarm occurs (automatic operation stop) 2. Press the [Stop/Manual] button. ...

The "Business Certainty · 2022 New Growth Conference" organized by the Chinese edition of Harvard Business Review was held in Beijing on December 16. SIASUN was listed on the "2022 China New Growth · Agile Leadership List" for "market-oriented and agile innovation". At the conference site, from the intelligent and scientific ...