Introduction of Xinjie MS6G-130 series inertia servo motor

It is reported that after a comprehensive evaluation by the user expert jury, network users and gongkong, Xinjie's XDM-60T10-E motion control PLC won the "Innovative Product Award" in the 13th annual automation selection activity of gongkong. ...

1. The switching quantity is also called the logical quantity, which means that there are only two values, 0 or 1, ON or OFF. It is the most commonly used control, and it is the advantage of PLC to control it, and it is also the most basic use of PLC. The intention of switching quantity manipulation is to use the current input combination of the switching quantity with the historical input ...

The usual inverter motor (hereinafter referred to as VFD) can only regulate the speed of the communication motor, and it can be open-loop or closed-loop, depending on the control method and VFD. This is the traditional V/F mode. The basic concept of servo is accurate, precise and fast positioning. Frequency conversion is servo ...

XC can be divided into multiple sub-series according to the incompatibility of functions, including XC1 (economy), XC2 (foundation), XC3 (standard), XC5 (enhanced) and their corresponding expansion modules, as well as special imitation ontology, activity control models, etc. Powerful function, complete variety, can be full ...

1. Air opening: a total air switch, which is the power control of the entire cabinet. I believe that every cabinet must have one thing. 2. PLC: This should be selected according to the needs of the project. For example, if the project is small, it can be an integrated PLC, but if the project is more ...

The ladder diagram of the PLC can be understood as a programming language like the assembly and other calculator languages, but the scale of use is different! And the general practice is to convert your ladder diagram into C or assembly language (determined by the CPU used by the PLC), and then use the assembly or C compilation system to compile ...

Common problems with Xinjie touch screen Poor contact Touch screen installation problemRemove the screen from the control cabinet and perform an operational test. If there is no problem with the operation, i.e. the installation problem causes the installation size to be re-measured, do not install it too tightly so as not to squeeze the touchpad. Correspondence...

1. Non-short-circuit overcurrent, which is mainly due to: (1) The motor is severely overloaded. (2) The motor accelerates too fast. (3) Due to the U/f ratio (torque compensation) setting is too high, the motor is in a light load condition. 2. Short circuit ...

The voltage waveform output by the inverter is similar to a sine wave, but not a real sine wave. Its waveform contains a large number of harmonic components, especially the higher harmonics will increase the output current of the inverter, form the motor winding heating, produce vibration and noise, accelerate the aging of insulation, and even ...

1. Maintenance of the inverter itself: Instantaneous overcurrent, overvoltage, undervoltage, overload, short circuit to ground, abnormal control circuit, then for the maintenance of the inverter itself, the overcurrent, overvoltage, undervoltage and so on set the limit value, when the inverter is running, if ...

There are many novices who are not familiar with the false load about the maintenance inverter, and the maintenance inverter uses the false load to keep many of their modules, because the maintenance novice generally does not know how to do this, and now the electric light is on to clarify that the module is going to be broken. A dummy load is a load with a resistor of several hundred ohms ( ...

Input and output loop debugging 1. Analog input (AI) loop debugging. Carefully check the address assignment of the I0 module; Check whether the loop power supply mode (internal power supply or external power supply) is consistent with the field instrument; Use a signal generator to add a signal to each channel at the field end, generally taking 0, 5 ...

Make accurate punctuality, read accurate punctuality, and stop accurate punctuality. Watchman number. Range: T600 - T618 (T600, T602, T604...) T618, numbered even) Punctuality. Accurate punctuality ...

1. Acknowledging the characteristics of the load such as load type, speed, and nature; 2. Acknowledging whether it is continuous work, long-term work, short-term work and other work characteristics; 3. Acknowledging the maximum consumption output value and the extra output value; 4. Acknowledging ...

1. The speed regulation power is high, which is an efficient speed regulation method. This is because after the frequency change, the motor is still working in close proximity to the synchronous speed, and the rated slip is fundamentally adhered to. It's just that in the frequency conversion equipment system, there will be conversion loss, and because of the influence of higher harmonics, the loss of the motor will increase.

(1) The analog signal is a small signal, which is very susceptible to external interference, and a double-layer shielded cable should be selected; (2) High-speed pulse signals (such as pulse sensors, digital disks, etc.) should be shielded cables, not only to prevent external interference, but also to prevent high-speed pulse signals from low-power.

It is necessary to route the signal line and the power line separately: When using the analog signal remote control inverter, in order to reduce the disturbance of the analog signal of the VFD and other equipment, please separate the signal line of the VFD control from the strong current circuit (main circuit and sequential control circuit). The spacing should be more than 30cm. Even in the control ...

In the process of century industry, the more top-level software and hardware planning for the suspension of frequency conversion skills, first according to the characteristics of traditional air compressor motors, comprehensively analyze the causes of energy consumption and operation characteristics, so as to plan the control of frequency conversion skills speed regulation, air skill tightening, pressure sensing skills improvement, etc.

At present, PLC has been widely used in various industries such as steel, petroleum, chemical industry, electric power, building materials, machinery manufacturing, cars, textile, transportation, environmental protection and culture and entertainment at home and abroad. 1 ...

On October 18, the final of the "2019 China Technology Competition - The 3rd National Industrial Robot Technology Use Technology Competition" sponsored by the Ministry of Industry and Information Technology, the Ministry of Human Resources and Social Security, the Ministry of Education, the All-China Federation of Trade Unions and the Central Committee of the Communist Youth League was officially opened in Jinan, Shandong Province.