Rorobot BML-1G071010[LP]/S The recommended load is 12g

Introduction: Rorobot Finger Module C8V4, Features and Applicable Scenarios: Large Clamping Force, Can Be Used in Series (Using Screw Accessory Kit PK) and Simplifies Tracheal Arrangement. It is mostly used in scenarios where multiple fingers work at the same time and the workpiece is compact, and the width of the workpiece is generally greater than 50mm Features: ...

Introduction: Rorobot BMC-4B32[H]/S Features: The fingertips are open in the positive pressure state, and the clamping is in the vacuum state, and it is recommended to use the soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertips G and the outer support fingertips D. Soft claw ...

Introduction: Rorobot Robot Soft Grip BMC-3G20[H]/S, B-3G20[H]/S is a strong small soft gripper that can grasp relatively heavy workpieces outside. Clamping force (0-0.6N) and clamping range (3-13mm), the recommended load is 60g. Compensates for the higher negative impact of other three-finger soft claws in grabbing ...

Introduction: Rorobot Flange Connection Module FCM-S01, Flange Connection Module [FCM] is a connection between the end of the robotic arm and the sliding mounting plate [SMP], which can be used with the quick-change module [QCM], which is divided into spring rod type (S) and fixed rod type (R). Features: Compliant with IS...

Introduction: Rorobot module B-4A30/M is a slender soft claw, suitable for jelly shells, test tubes, badminton, cylindrical, hollow columns and other fragile and fragile objects of non-destructive internal support handling and sorting, to ensure that the product will not be scratched, reduce the defect rate. When multiple soft jaws are connected in series, ...

Introduction: FlexTouch/Rorobot Flange Connection Module FCM-R04 Features: It conforms to the ISO9409-1:2004 standard (i.e., the national standard GB/T 14468.1-2006/), and is suitable for most robot flanges on the market. Lightweight for lightweight articulated machines ...

Introduction: Rorobot Finger Module C6V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Soft Touch/Rorobot Finger Module FM-B7V1, Features and Applicable Scenarios: Combination of two-finger modules, compact structure, small space occupation. The spacing and installation angle are not adjustable, which is suitable for clamping tiny, thin and light workpieces. Features: Features and applicable scenarios: two-finger ...

Introduction: Rorobot Finger Module A4V5, Features and Applicable Scenarios: The module is thinner, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot Finger Module C3V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Soft Touch/Rorobot Finger Module FE-A3V1, Features and Applicable Scenarios: Combination of two-finger modules, compact structure, small footprint. The spacing and installation angle are not adjustable, and it is suitable for clamping small, light and thin workpieces. Features: Features and applicable scenarios: ...

Introduction: Soft-Touch/Rorobot Actuator LCH-U is a lightweight actuator designed for soft-touch grippers with both positive pressure and vacuum output, and can be used for both multi-channel and asynchronous drives Product parameters Enter the air supply 0.4—0.6MPa Flow rate> 200L/min Lose...

Introduction: Rorobot BML-3G20[H]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted by supporting the fingertip distance G. Soft-touch materials are divided into conventional type [H] and non-marking ...

Introduction: Rorobot Finger Module C5V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and ...

Introduction: Rorobot Finger Module FM-A4V2, Features and Applicable Scenarios: Independent Installation, Can Be Installed with SMP Sliding Mounting Plate, Finger Spacing and Angle Adjustable, Fixing Method: Can Be Fixed from Four Directions (Optional), Air Intake Mode: Air Intake Connector Can Be Installed from Three Directions (Optional) . ...

Introduction: Rorobot Soft Jaw BMC-1G364030[HAS]/M, is a strengthened version of the single finger soft jaw, the recommended fingertip and workpiece distance is (19-28) mm, the recommended load of one finger soft jaw is (0-500) G, and the external gripping clamping force is (0-11) N. Features: Positive pressure state fingertips ...

Introduction: Rorobot FM-C4V5/LS1 Product parameters Positive pressure stroke: 11mm Negative pressure stroke: 9mm Safe working air pressure: 120kPa Recommended load: 145g Tare weight: 28g Our customer-centric service philosophy ...

Introduction: Rorobot BMC-4H18[H]/S Features: The fingertips are open in the positive pressure state, clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by using the external support fingertip distance D. The soft claw material is divided into conventional type [H and non-marking ...

Introduction: Rorobot Finger Module B6V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and ...

Introduction: Rorobot BMC-3B14/S Features: The fingertips are open in the positive pressure state, and clamped in the negative pressure state, it is recommended to use it with a soft-touch air driver, and the working air pressure can be adjusted with the distance between the fingertips of the inner support and the fingertips. The soft claw material is divided into conventional type and non-marking type, when ...