How to choose VIRONT CMT password login?

1. Check the hardware connections: Make sure the touchscreen is properly connected to the device and that all cables and connectors are in working order. Check if the connector is loose or damaged, and if so, reconnect or replace the connector. 2. Check the drivers: Make sure the device is properly installed.

Precautions when using Verun Tong inverter 　　When shipping and storage During the storage period, it is necessary to ensure that the inverter is not subjected to physical shocks and oscillations. It is also necessary to ensure that they are not exposed to rain and are not placed in places where the ambient temperature is too high. When transferring, hold the bottom of the body ...

1. Why can't the screen display Chinese normally, but the display is garbled? Answer: This situation is generally caused by not choosing the correct Chinese font, just choose a Chinese font, the specific operation steps are as follows: 1) In EasyBuilder soft...

When the touch function of the touch screen fails, first try to enter offline mode to verify whether the touch screen backlight is burned out. If the cause of the fault is verified to be a burned-out backlight, then we can follow the steps below to temporarily restore the touch function of the touchscreen (take the Proface GP series touchscreen as an example below).

1. Open the Weilun software; 2. Click "Edit" - system parameters; 3. Enter "Mitsubishi model" in the pop-up dialog box name; 4. Check the "PLC" below to select the PLC type; 5. Communication can be realized by connecting the machine with a communication line. ...

Open the Veriton touch screen programming software, select [Common] in the main interface and open it In the Common drop-down menu, select System Parameters and click Open. Then select [HMI Attributes] in the pop-up system parameter setting menu and click OK. ...

Sometimes we need to monitor and change the program of PLC equipment, and when it is inconvenient to connect to PLC or there is no communication line, we can choose to achieve it through the penetration function of the touch screen. The traversal communication function consists of the following two modes: Ethernet When using [Ethernet] ...

The three main types of Weiluntong touch screens are: resistive technology touch screen, surface acoustic wave technology touch screen, and capacitive technology touch screen. Each type of Veruntong touch screen has its own advantages and disadvantages, let's learn about resistive touch screens today! The outer layer of the resistive screen is generally ...

1. The screen is powered off, and the first DIP switch behind is dialed to the ON position; 2. Power on again, a white cross cursor will appear on the screen, click the middle of the cross cursor vertically, after the point (the time can not be too short), the cross cursor will automatically jump to the next position, the cross light ...

1. Plug in the U disk on the touch screen, you don't need to power off the screen, the screen supports the hot-swap function, but at this time, it is best not to communicate with external devices to reduce unnecessary impact. When the screen detects an external device, a dialog box will pop up, select the second Upload Project option ...

1. Generally, in the lower right corner of the touch screen, there is a small black arrow button, click and enter the correct password, you can enter the system settings. There are generally three ways to enter the system setting of the TK6070ih touch screen: 1,Generally in the lower right corner of the touch screen, ...

1. Omron NJ controller programming 1. The structure data type required for the new project, such as the Boolean switch to be used in this example to create a structure data type of "take-up machine IO", and the integer data used in this example to create a "take-up machine".

Touch screen mobile phone capacitive touch screen and resistive touch screen are mainly different in touch sensitivity, accuracy, cost, multi-touch feasibility, damage resistance, cleaning, and sunlight visual effect. Touch sensitivity, 1. Resistive touch screen: pressure is needed to make all layers of the screen ...

Ambient light factor, infrared receiver tube has a working range between minimum sensitivity and maximum illumination, but touch screen products can not limit the range of use, from the dark cabaret room to the outdoor use under the high-intensity sunlight on Hainan Island, as a product, it must adapt. Rapid detection ...

5.1 Why does the prompt "EasyWindow must run from EasyManager or EasyBuider" appear when using the offline simulation function? If the serial port is selected as com4 or above (excluding com4), the prompt will be displayed, but it will not affect the download function, ...

1. Generally, in the lower right corner of the touch screen, there is a small black arrow button, click and enter the correct password, you can enter the system settings. However, when configuring, you can disable this button in the software system settings. 2. Set the system bit LB-9020 in the touch screen to ON...

Method 1: Reconfigure capacitive screen parameters through the configuration file The configuration parameters of the capacitive touch screen are saved in the serial port screen, and the sensitivity of the capacitive touch screen can be configured by writing new parameters. For customers who need to add a panel to a capacitive touch screen, panel samples and structures can be ...

1. First of all, open the Weilun touch screen to modify the software, and be sure to choose the software corresponding to the type of touch screen; 2. Modify the required touch screen screen; 3. Then open the "System Settings" button under the "Common" menu in the upper left corner; 4. Set the pop-up window in the system ...

1. The memory address is different. The memory address of the PW touch screen uses the local hold register, while the memory address of the RW uses the hold register index to send RWI. 2. The address range is different. The address range of the LW of the touch screen is 0 to 524287, while the address range of the RW is 0 to .

18. Macro calculation: The values to be calculated are read, and then the data is calculated and written to LW0. 19. According to the different selections of the project menu, two different direct windows will pop up with one button: Macro commands are triggered by a button to read the ...