1. Disconnect the control power supply: Before making the low-voltage terminal contact adjustment, the control power supply should be disconnected first to avoid the current directly or indirectly passing through the relay contact, and avoid electric shock or damage to the relay.
2. Open the relay cover: Open the relay cover and you can see the internal structure of the relay.
3. Locate the low-voltage contacts: Inside the relay, locate the location of the low-voltage contacts. Most relays will indicate the location and identification of the contacts, if you have any doubts, you can refer to the relay manual or ask the manufacturer or other professionals.
4. Adjust the low-voltage end contacts: Using the adjustment tool, gradually adjust the low-voltage end contacts until the desired state is reached. When adjusting, it needs to be adjusted gradually, small adjustments, and then gradually plug and unplug the control power supply and test the working state of the relay until the desired effect is achieved.
5. Close the relay cover: When the low-voltage end contact adjustment is completed, close the relay cover to ensure that the contacts are correct.
It should be noted that the adjustment of the low-voltage end contacts needs to be operated by professionals, otherwise it may affect the normal operation of the relay. Therefore, before making contact adjustments, you should first understand the working principle of the relay and its electrical parameters to ensure the correctness and safety of the adjustment.
|
More on that
|
Siemens APT Relays – Classified by relay form factor
(1) Miniature relay: the longest side of the relay is not more than 10 mm.
(2) Ultra-miniature relay: the longest side size is greater than 10 mm, but not more than 25 mm.
(3) Small miniature relay: the longest side size is greater than 25 mm, but not large...
|
|
Siemens APT Relays – Reliability of Relays
1. The influence of the environment on the reliability of the relay: the average time between failures of the relay is the highest under GB and SF, reaching 820,000h, while in the NU environment, it is only 60,000h.
2. The influence of quality grade on the reliability of relays: when the relay of A1 quality grade is selected, the flat ...
|
|
Siemens APT transformer – common faults and analysis of voltage transformers
(1) The insulation between the iron chips is damaged
Problem: The temperature rises during operation.
Possible causes of the problem:
(1) Poor insulation between iron chips
(2) The use of harsh environmental conditions or long-term operation at high temperature to promote the aging of insulation between iron chips.
（ ...
|
|
Introduction to the features of the full range of Siemens APT metal button FM products
Seeking advanced, perfect and excellent Xijia APT to concentrate on research and development, and constantly change customs, the launch of the metal flat button indicator FM series is to complete the perfect integration of appearance and performance.
Ultra-thin flat round device, metal shell and buttons, high-value appearance
Product ...
|
|
Siemens APT current transformer - how to choose a current transformer?
First, the principle of primary parameter selection of current transformer
The rated primary current of the current transformer is determined by the actual load of the tested circuit, and the rated primary current of the current transformer should not be less than the rated primary current of the circuit.
|
|
Siemens APT Relays – Common Causes of Failure of Solid State Relays
1. The reason for the frequent disconnection of the coil: whether the solid state relay is cleaned with ultrasonic, whether the coil is overvoltaged, etc., will cause the coil to be disconnected.
2. The reason for the insufficient power supply of the coil: First, it is necessary to confirm the voltage of the solid state relay coil. If the voltage supplied to the coil is lower than ...
|
|
Siemens APT Relays – Classified by relay load
(1) Micro-power relay: when the contact open circuit voltage is DC 28V, the (resistivity) is 0.1A, 0.2A relay.
(2) Weak power relay: when the contact open circuit voltage is DC 28V, (resistivity) is 0.5A, 1A relay.
(3) Medium power relay ...
|
|
TL series police lights frequently asked questions
1. How many light sources are there for the TL-70 police light?
There are 3 types, namely LED, incandescent and xenon.
2. What are the colors of the TL-70 police light?
There are 5 types, which are red, yellow, green, blue, and white.
3. What are the types of TL-70 police lights?
3 ...
|
|
ALH-0.66 series transformer FAQ
1. What is the maximum voltage that can be used for an ALH transformer?
AC low voltage up to 720V
2. Is there a protective grade product for ALH transformers?
II-P AND III-P are available in both protective grades
3. What is the maximum primary current of ALH transformer?
The maximum primary side current is 8 ...
|
|
AD16-30JC Series Combination Light FAQ
1. What are the basic combination colors of combination lights?
Red, yellow, green, blue, white, bicolor.
2. What are the different types of combination light panes?
F, H, L, V, G any combination
3. Is the lampshade detachable?
OK
4. Combination light ...
|
|
Siemens APT Current Transformer - The difference between voltage transformer and current transformer
The difference between the voltage transformer and the current transformer in terms of effect principle The primary difference is that the operating conditions are very different during normal operation, and the main performance is as follows:
1) The current transformer can be short-circuited twice, but it cannot be opened; The voltage transformer can be opened twice, but it must not be short-circuited
2) ...
|
|
Siemens APT transformer - the use, principle and selection of current transformer
The principle of the current transformer is based on the principle of electromagnetic induction. A current transformer is composed of a closed core and windings. Its primary side winding turns are very small, string in the line of the current that needs to be measured, so it often has all the current of the line flowing through, the number of turns of the secondary side winding is relatively large, and the series ...
|
|
Siemens APT Relays - Installation Precautions for High and Low Voltage Relays
1. Choose the right relay: When choosing a high and low voltage relay, you should choose the right product according to your needs, such as selecting according to the rated voltage, current and other information
2. Installation location: high and low voltage relays should be installed in dry, ventilated, non-corrosive gas, less dusty areas, ...
|
|
Siemens APT current transformer – the difference between the ratio on a current transformer and the ratio on a watt-hour meter
1. Differences in use
The conversion ratio of the current transformer is inconsistent with the transformation ratio of the ammeter, which will lead to the inability to use the displayed value of the ammeter directly, and the proportional conversion must be carried out;
If the transformer of ratio 5 is used on the meter of ratio 1, the secondary current of CT will generally exceed 1A, so that the transformer of 5 is used on a meter of 1 ratio. Than 1 ...
|
|
Siemens APT Pushbutton Switches - Introduction to the types of metal pushbutton switches
Common types of metal button switches include self-locking switches, self-reset switches, knob gear switches, lever gear switches, locking switches, etc.; Because the metal button switch is small in size, easy to install, metal material, voltage can be used from 9-220V, and the appearance of metal texture ...
|
|
Siemens APT Relays – The difference between AC relays and DC relays
1. Structural characteristics of AC relays
The coil of the AC relay is shorter, and the wire diameter is thicker, mainly because the coil is passed through the alternating current, the reactance is larger, and the thick wire diameter can reduce the internal resistance and reduce the heat generation.
|
|
Siemens APT Relays – The difference between solid state relays and intermediate relays
First, the solid-state relay has no contacts and coils in the structure, which can be opened and closed at a high frequency and will not produce sparks, and has a long service life;
Second, the intermediate relay is generally only used for the control loop, and cannot work with load, and will make a "pop" sound when it is sucked in;
...
|
|
Siemens APT Relays - Common Problems and Solutions of Relays
First, the contact is loose and cracks
The contact is the electrical contact part of the relay to complete the switching load, and the contact of some products is riveted and pressed, and its main drawbacks are loose contacts, cracked contacts or excessive dimensional position deviation. This will affect the contact reliability of the relay. Shovel appears ...
|
|
Siemens APT Relays - Selection Method for Solid State Relays
1. When selecting the solid-state relay used in the printed circuit board with small current specifications, because the lead terminal is made of high thermal conductivity material, the soldering should be carried out under the condition that the temperature is less than 250 °C and the time is less than 10S.
|
|
Siemens APT current transformer - common faults and solutions of current transformers
1. There is an abnormal noise or over-temperature of the iron core
Cause of failure: When the current transformer is in operation, if there is an open circuit or overload in the secondary circuit, it will lead to abnormal sound and over-temperature of the core.
|
|
Contact
working hours
