Introduction: The transmitter and receiver on a thru-beam photoelectric sensor are aligned in opposite directions. The advantage of this is that the beam reaches the receiver directly, so a long detection distance and high excess gain can be achieved. These sensors are capable of reliably detecting almost any object. The angle of incidence, surface characteristics, object color, etc., do not affect the reliability of the sensor.
Product Details
IO-link interface for service and process data
Multiple frequencies to prevent mutual interference (anti-crosstalk)
Extended temperature range
-40°C ... 60°C
High degree of protection: IP69K
Transmitter OBE20M-R100-S-IO-V31-L
Receiver OBE20M-R100-2EP-IO-V31-L
General specifications
Effective detection distance 0 ... 20 m
The limit value of the detection range is 30 m
Light source: Laser diode
Light source type Modulates visible red light
Laser ratings
Pay attention to the laser , never look directly at the laser beam
Laser class 1
Wavelength 680 nm
Beam divergence > 5 mrad ; d63 < 2 mm with a range of 250 mm ... 750 mm
Pulse length 1,6 μs
Repetition rate max. 17,6 kHz
Pulse energy maximum 9,6 nJ
The diameter of the light spots is about 50 mm and 20 m apart
The divergence angle is about 0,3 °
Ambient light limit EN 60947-5-2 : 30000 Lux
Functional safety-related parameters
MTTFd 440 a
Mission time (TM) 20 a
Diagnostic Coverage (DC) 0 %
Indicator/method of operation
Working Indicator Green LED:
Lights up continuously - powered
Flashing (4Hz) - Short circuit
Flashing with short intermittent (1 Hz) - IO-Link mode
Function Indicator Yellow LED:
Solid - The light path is unobstructed
Continuous Off - Object detected
Flickering (4 Hz) – Insufficient operating reserve
Control Element Receiver: Bright/Dark On
Control Element Receiver: Sensitivity Adjustment
Parameterized indicator IO Link communication: Green LED temporarily off (1 Hz)
Electrical Specifications
Operating voltage 10 ... 30 V DC
Ripple max. 10 %
No-load current transmitter: ≤ 13 mA
Receiver: ≤ 13 mA at 24 volts
Protection class III
interface
Interface Type IO-Link (via C/Q = Pin 4)
IO-Link fix 1.1
Device ID Transmitter: 0x110402 (1115138)
Receiver: 0x110302 (1114882)
Transmission rate COM 2 (38.4 kb/s)
Minimum cycle time 2,3 ms
Process Data Bit Width Emitter:
Process data output: 2 bits
Receiver:
Process data entry: 2 digits
Process data output: 2 bits
SIO mode support Yes
Compatible with primary port type A
input
Test Input: Under +UB the transmitter is deactivated
output
Switch Type The switch type of this sensor is changeable. The default settings are:
C/Q - Pin 4: NPN NO/OB, PNP NO/ON, IO-Link
/Q - Pin2: NPN is normally closed/on and PNP is normally on/dark
Signal output: 2 push-pull (4-in-1) outputs, short-circuit protection, reverse polarity protection, overvoltage protection
Switching voltage max. 30 V DC
Switching current max. 100 mA, impedance load
Use categories DC-12 and DC-13
Voltage drop ≤ 1,5 V DC
Switching frequency 1250 Hz
The response time is 0,4 ms
compliance
Communication interface IEC 61131-9
The product standard is EN 60947-5-2
Laser safety EN 60825-1:2014
Certifications and certificates
UL listed E87056, cULus recognized, class 2 power supply, type class 1
FDA certifies IEC 60825-1:2007 to 21 CFR 1040.10 and 1040.11, subject to deviations from Laser Notice No. 50 issued on June 24, 2007
Environmental conditions
Ambient temperature -40 ... 60 °C (-40 ... 140 °F)
Storage temperature -40 ... 70 °C (-40 ... 158 °F)
Mechanical Specifications:
Housing width 11 mm
Housing height 44,5 mm
Case depth 21,5 mm
Degree of protection IP67 / IP69 / IP69K
Connects M8 x 1 connectors, 4-pin
material
Housing PC (Polycarbonate)
Optical end-face PUMA
Mass Transmitter: approx. 10 g Receiver: approx. 10 g
Our customer-centric service concept: the pursuit of a full range of services is a high-quality, high-standard service, the pursuit of every detail of the service process. It is impossible for interests to blossom into brilliant flowers from lies. Only by being professional and careful in every process, every action and every detail of the service can we meet or even exceed customer expectations and make customers satisfied and recognize us. Honest, professional, affordable, and fast, so you can rest assured. "Honest and professional service, affordable price, continuous improvement" is our service philosophy.
This article introduces P+F/Double Hair sensor OBE20M-R100-S2EP-IO-V31-L through-beam products, if you are interested in P+F/Double Hair sensor, please also contact our customer service, we are looking forward to your call, hope our technology and service can bring you a better experience.
|
More on that
|
P+F/Through-beam photoelectric sensor OBE2000-R2-SE0 20 g
Description: The P+F/P+F/Through-beam photoelectric sensor OBE2000-R2-SE0 with its ultra-small housing design and 45° cable outlet provides maximum installation freedom, even in very space-constrained conditions.
Product Features ...
|
|
P+F capacitive sensor CJ10-30GM-WO with a working distance of 10mm
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Capacitive sensor CBN10-F46-E2-10M core cross-section: 0.14mm2
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F Capacitive Sensor CJ40-FP-A2-P1 40mm
Introduction: P+F capacitive sensor CJ40-FP-A2-P1 40 mm, non-flush; 4-wire DC; The switching distance can be set over a wide range using a potentiometer. Up to two conductors with the same core cross-sectional area can be installed with one terminal connector.
...
|
|
P+F/Triangulation sensor OQT150-R100-2EP-IO 10-30VDC
Product Description: Measurement core technology, 150 mm detection range, red light, IO-Link, 2 x push-pull output, 2 m fixed cable, miniature design with multiple mounting options, Multipixel Technology (MPT) - Flexibility and adaptability, switching diffuse reflection mode sensors, reducing equipment ...
|
|
P+F/Reflective sensor ML100-55/103/115a 7 m
Description: Retroreflective sensor ML100-55/103/115a photoelectric sensor with polarization filter, plastic housing, 5 m detection range, red light, adjustable sensitivity, on/dark, DC, PNP output, fixed cable with M8 plug.
...
|
|
P+F/Double Blessing Inclination Sensor INY030D-F99-B16-V15 weighs 240g
Description: Inclination sensors reliably detect inclination in factory automation and mobile device applications, making them the ideal solution for leveling mobile work platforms, for example. The sensor is able to continuously monitor the tilt angle of the platform and indicate when it is necessary to readjust the ...
|
|
P+F/UBE15M-F54-H1-V1 housing PBT
Introduction: An ultrasonic through-beam sensor consists of a transmitter and a receiver mounted facing each other. Ultrasonic through-beam sensors work by emitting sound waves from the transmitter to the receiver to detect objects through the sound beam being interrupted by the target object. The emitter produces ultrasonic ...
|
|
P+F/Pixel Sensor GL30-RT / 32 / 40A / 98A Light/Dark
Product Introduction: Photocell Sensor, Zinc Die-Cast Housing, 30mm Slot Width, Red Light, Light/Dark, Sensitivity Regulator, DC Version, PNP Output, 3-Pin M8 Plug, Optimized for Detecting Small Parts, High Switching Frequency, Multi-Device Installation Possible, No Mutual Interference (No Crosstalk), Sensitivity ...
|
|
P+F Inductive Sensor NBB8-18GM60-US 8mm
Summary: Inductive proximity sensors are the product of choice for most applications that require the precise and non-contact detection of metal objects in machinery or automation. As a pioneer and market leader in the field of sensors, we offer our customers innovative, high-quality inductors.
|
|
P+F Capacitive Sensor CJ40-FP-A2-P4 4-wire
Introduction:P+F capacitive sensor CJ40-FP-A2-P4 series rectangular, housing material is POM / metal, output type 4 wires, non-flush mounting, DC voltage type, screw terminal connection type, protection class IP65.
...
|
|
P+F Zener Barrier Z System 35 mm DIN rail
Introduction: P+F/Plus Forziner Barrier - cost-saving, easy to install explosion protection. Mounted directly on a 35 mm DIN rail. With the accessory, the required grounding can be carried out directly on the DIN mounting rail.
Product Details
Zen ...
|
|
P+F/Throughbeam GD18 / GV18 /73/120
Product Introduction: Thru-beam sensor, M18 threaded housing design, plastic housing, front optical face, 20m detection distance, red light, light and dark, DC version, 2 PNP outputs, M12 plug, high efficiency line, short M18 plastic housing application, very high detection range, 4 LEDs ...
|
|
P+F/Optical Data Coupler DAD15-8P Spring Terminals
Product Introduction: The optical communication system supports two-way communication between storage and retrieval systems, transmission vehicles, automatic guided vehicles and monorail conveyors. This is an alternative to complex and problematic cables, slip rings and other transmission solutions. The transmission between the two sites is replaced by infrared light, which is made up of several ...
|
|
P+F/UB400-F77-E0-V31 ultrasonic direct detection sensor
Introduction:P+F/P+F/Double Blessing Ultrasonic Direct Detection Sensor UB400-F77-E0-V31 Working Voltage 20 ... 30 V DC, ripple 10 %SS ; 12 ... 20 V DC sensitivity reduced to 90%; Output Type: 1-way switch output E0, NPN, normally open.
...
|
|
P+F/Capacitive sensor CBN10-F46C-EI 7mm
Introduction: Capacitive sensors can be used to detect targets in almost any material, including metal. These sensors are used in a wide range of applications for level and flow control, mainly liquids, particles and powders.
Give birth...
|
|
P+F/Inclination sensor INX360D-F99-U2E2-V15 range 0~360°
Product Description: The new generation of the F99 inclination measurement sensor is ideal for industrial environments due to its simplicity, durability and compact housing. The F99 inclination measurement sensor offers a standardized 4 ... 20 mA analogue interface with a measuring range of 0 ... 360° between, no need for expensive total ...
|
|
P+F inductive sensor NBB2-12GM50-E3-V1 2 mm
Introduction: Smooth or threaded stainless steel cylindrical housing for inductive sensors; reverse polarity protection and short circuit protection; LED status indicates M8, M12 connector connection or terminal wiring mode; PVC, PUR or silicon cable outlet; 2-wire, 3-wire, 4-wire DC, AC, NAMUR output mode to ...
|
|
P+F Capacitive Sensor CJ10-30GK-WS 10mm non-flush
Introduction: Capacitive sensors can be used to detect targets in almost any material, including metal. These sensors are used in a wide range of applications for level and flow control, mainly liquids, particles and powders.
...
|
|
P+F/Inductive sensor NBB4-12GM30-E2-V1 4mm
Summary: Inductive proximity sensors are the preferred product for most applications that require the precise and non-contact detection of metal objects in mechanical or automated equipment. As a pioneer and market leader in the field of sensors, we offer our customers innovative, high-quality electrical products.
|
|
Contact
working hours
